Abstract
In this chapter, we present different multiscale modeling techniques to determine the elastic and interfacial properties of carbon nanotube (CNT)-reinforced polymer composites. The elastic properties of CNT-reinforced composite (hereinafter the “nanocomposite”) are obtained in a two-step approach. First, at the nanoscale level, molecular dynamics (MD) and atomistic-based continuum (ABC) techniques are used to determine the effective elastic properties of a representative volume element (RVE) that is comprised of a nanofiller and its immediate surrounding. Second, at the microscale level, several micromechanics models and hybrid Monte Carlo finite-element (FE) simulations are used to determine the bulk properties of nanocomposite. The interfacial properties are determined through pullout test using MD and ABC techniques. The effect of length, diameter, agglomeration, waviness, defects, and orientation of CNTs on the elastic and interfacial properties of nanocomposites is also investigated. The development of multiscale modeling and the proper selection of simulation parameters are discussed in detail. The results of several studies are presented and compared to show the inherited limitations in each technique.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Ajayan, P.M., Schadler, L.S., Giannaris, C., Rubio, A.: Single-walled carbon nanotube-polymer composites: strength and weakness. Adv. Mater. 12, 750–753 (2000). doi:10.1002/(SICI)1521-4095(200005)12:10<750::AID-ADMA750>3.0.CO;2-6
Alder, B.J., Wainwright, T.E.: Phase transition for a hard sphere system. J. Chem. Phys. 27, 1208–1211 (1957). doi:10.1063/1.1743957
Alian, A.R., Kundalwal, S.I., Meguid, S.A.: Interfacial and mechanical properties of epoxy nanocomposites using different multiscale modeling schemes. Compos. Struct. 131, 545–555 (2015a). doi:10.1016/j.compstruct.2015.06.014
Alian, A.R., Kundalwal, S.I., Meguid, S.A.: Multiscale modeling of carbon nanotube epoxy composites. Polymer 70, 149–160 (2015b). doi:10.1016/j.polymer.2015.06.004
Allaoui, A., Bai, S., Cheng, H.M., Bai, J.B.: Mechanical and electrical properties of a MWNT/epoxy composite. Compos. Sci. Technol. 62, 1993–1998 (2002). doi:10.1016/S0266-3538(02)00129-X
Awad, I., Ladani, L.: Mechanical integrity of a carbon nanotube/copper-based through-silicon via for 3D integrated circuits: a multi-scale modeling approach. Nanotechnology 26, 485705 (2015). doi:10.1088/0957-4484/26/48/485705
Brenner, D.W.: Empirical potential for hydrocarbons for use in simulating the chemical vapor deposition of diamond films. Phys. Rev. B 42, 9458–9471 (1990). doi:10.1103/PhysRevB.42.9458
Brenner, D.W.: The art and science of an analytic potential. Phys. Status Solidi B 217, 23–40 (2000). doi:10.1002/(SICI)1521-3951(200001)217:1<23::AID-PSSB23>3.0.CO;2-N
Coleman, J.N., Cadek, M., Blake, R., Nicolosi, V., Ryan, K.P., Belton, C., Fonseca, A., Nagy, J.B., Gun’ko, Y.K., Blau, W.J.: High performance nanotube-reinforced plastics: understanding the mechanism of strength increase. Adv. Funct. Mater. 14, 791–798 (2004). doi:10.1002/adfm.200305200
Coleman, J.N., Khan, U., Blau, W.J., Gun’ko, Y.K.: Small but strong: a review of the mechanical properties of carbon nanotube-polymer composites. Carbon 44, 1624–1652 (2006a). doi:10.1016/j.carbon.2006.02.038
Coleman, J.N., Khan, U., Gun’ko, Y.K.: Mechanical reinforcement of polymers using carbon nanotubes. Adv. Mater. 18, 689–706 (2006b). doi:10.1002/adma.200501851
Coluci, V.R., Dantas, S.O., Jorio, A., Galvão, D.S.: Mechanical properties of carbon nanotube networks by molecular mechanics and impact molecular dynamics calculations. Phys. Rev. B 75, 075417 (2007). doi:10.1103/PhysRevB.75.075417
Cooper, C.A., Cohen, S.R., Barber, A.H., Wagner, H.D.: Detachment of nanotubes from a polymer matrix. Appl. Phys. Lett. 81, 3873 (2002). doi:10.1063/1.1521585
Dauber-Osguthorpe, P., Roberts, V.A., Osguthorpe, D.J., Wolff, J., Genest, M., Hagler, A.T.: Structure and energetics of ligand binding to proteins: Escherichia coli dihydrofolate reductase-trimethoprim, a drug-receptor system. Proteins Struct. Funct. Genet. 4, 31–47 (1988). doi:10.1002/prot.340040106
Desai, A.V., Haque, M.A.: Mechanics of the interface for carbon nanotube-polymer composites. Thin-Walled Struct. 43, 1787–1803 (2005). doi:10.1016/j.tws.2005.07.003
Dumlich, H., Gegg, M., Hennrich, F., Reich, S.: Bundle and chirality influences on properties of carbon nanotubes studied with van der Waals density functional theory. Phys. Status Solidi B 248, 2589–2592 (2011). doi:10.1002/pssb.201100212
Falvo, M.R., Clary, G.J., Taylor, R.M., Chi, V., Brooks, F.P., Washburn, S., Superfine, R.: Bending and buckling of carbon nanotubes under large strain. Nature 389, 582–584 (1997). doi:10.1038/39282
Frankland, S.J.V., Harik, V.M.: Analysis of carbon nanotube pull-out from a polymer matrix. Surf. Sci. 525, L103–L108 (2003). doi:10.1016/S0039-6028(02)02532-3
Frankland, S.J.V., Harik, V.M., Odegard, G.M., Brenner, D.W., Gates, T.S.: The stress–strain behavior of polymer–nanotube composites from molecular dynamics simulation: modeling and characterization of nanostructured materials. Compos. Sci. Technol. 63, 1655–1661 (2003). doi:10.1016/S0266-3538(03)00059-9
Gao, G., Çagin, T., Goddard, W.A.: Energetics, structure, mechanical and vibrational properties of single-walled carbon nanotubes. Nanotechnology 9, 184–191 (1998). doi:10.1088/0957-4484/9/3/007
Gojny, F., Wichmann, M., Fiedler, B., Schulte, K.: Influence of different carbon nanotubes on the mechanical properties of epoxy matrix composites—a comparative study. Compos. Sci. Technol. 65, 2300–2313 (2005). doi:10.1016/j.compscitech.2005.04.021
Gou, J., Minaie, B., Wang, B., Liang, Z., Zhang, C.: Computational and experimental study of interfacial bonding of single-walled nanotube reinforced composites. Comput. Mater. Sci. 31, 225–236 (2004). doi:10.1016/j.commatsci.2004.03.002
Grujicic, M., Sun, Y.-P., Koudela, K.L.: The effect of covalent functionalization of carbon nanotube reinforcements on the atomic-level mechanical properties of poly-vinyl-ester-epoxy. Appl. Surf. Sci. 253, 3009–3021 (2007). doi:10.1016/j.apsusc.2006.06.050
Haghighatpanah, S., Bolton, K.: Molecular-level computational studies of single wall carbon nanotube-polyethylene composites. Comput. Mater. Sci. 69, 443–454 (2013). doi:10.1016/j.commatsci.2012.12.012
Han, Y., Elliott, J.: Molecular dynamics simulations of the elastic properties of polymer/carbon nanotube composites. Comput. Mater. Sci. 39, 315–323 (2007). doi:10.1016/j.commatsci.2006.06.011
Hao, X., Qiang, H., Xiaohu, Y.: Buckling of defective single-walled and double-walled carbon nanotubes under axial compression by molecular dynamics simulation. Compos. Sci. Technol. 68, 1809–1814 (2008). doi:10.1016/j.compscitech.2008.01.013
Herrera-Franco, P.J., Drzal, L.T.: Comparison of methods for the measurement of fibre/matrix adhesion in composites. Composites 23, 2–27 (1992). doi:10.1016/0010-4361(92)90282-Y
Hone, J., Whitney, M., Piskoti, C., Zettl, A.: Thermal conductivity of single-walled carbon nanotubes. Phys. Rev. B 59, 2514–2516 (1999). doi:10.1103/PhysRevB.59.R2514
Iijima, S.: Helical microtubules of graphitic carbon. Nature 354, 56–58 (1991). doi:10.1038/354056a0
Jam, J.E., Pourasghar, A., kamarian, S., Maleki, S.: Characterizing elastic properties of carbon nanotube-based composites by using an equivalent fiber. Polym. Compos. 34, 241–251 (2013). doi:10.1002/pc.22401
Jones, J.E.: On the determination of molecular fields. II. From the equation of state of a gas. Proc. R. Soc. Math. Phys. Eng. Sci. 106, 463–477 (1924). doi:10.1098/rspa.1924.0082
Krishnan, A., Dujardin, E., Ebbesen, T.W., Yianilos, P.N., Treacy, M.M.J.: Young’s modulus of single-walled nanotubes. Phys. Rev. B 58, 14013–14019 (1998). doi:10.1103/PhysRevB.58.14013
Kundalwal, S.I., Ray, M.C.: Effective properties of a novel continuous fuzzy-fiber reinforced composite using the method of cells and the finite element method. Eur. J. Mech. A Solids 36, 191–203 (2012). doi:10.1016/j.euromechsol.2012.03.006
LeSar, R.: Introduction to Computational Materials Science: Fundamentals to Applications. Cambridge University Press, Cambridge, NY (2013)
Li, C., Chou, T.-W.: A structural mechanics approach for the analysis of carbon nanotubes. Int. J. Solids Struct. 40, 2487–2499 (2003a). doi:10.1016/S0020-7683(03)00056-8
Li, C., Chou, T.-W.: Elastic moduli of multi-walled carbon nanotubes and the effect of van der Waals forces: modeling and characterization of nanostructured materials. Compos. Sci. Technol. 63, 1517–1524 (2003b). doi:10.1016/S0266-3538(03)00072-1
Li, Y., Liu, Y., Peng, X., Yan, C., Liu, S., Hu, N.: Pull-out simulations on interfacial properties of carbon nanotube-reinforced polymer nanocomposites. Comput. Mater. Sci. 50, 1854–1860 (2011). doi:10.1016/j.commatsci.2011.01.029
Li, C., Medvedev, G.A., Lee, E.-W., Kim, J., Caruthers, J.M., Strachan, A.: Molecular dynamics simulations and experimental studies of the thermomechanical response of an epoxy thermoset polymer. Polymer 53, 4222–4230 (2012). doi:10.1016/j.polymer.2012.07.026
Liao, K., Li, S.: Interfacial characteristics of a carbon nanotube-polystyrene composite system. Appl. Phys. Lett. 79, 4225–4227 (2001). doi:10.1063/1.1428116
Littell, J.D., Ruggeri, C.R., Goldberg, R.K., Roberts, G.D., Arnold, W.A., Binienda, W.K.: Measurement of epoxy resin tension, compression, and shear stress–strain curves over a wide range of strain rates using small test specimens. J. Aerosp. Eng. 21, 162–173 (2008). doi:10.1061/(ASCE)0893-1321(2008)21:3(162)
Lordi, V., Yao, N.: Molecular mechanics of binding in carbon-nanotube-polymer composites. J. Mater. Res. 15, 2770–2779 (2000). doi:10.1557/JMR.2000.0396
Matveeva, A.Y., Pyrlin, S.V., Ramos, M.M.D., Böhm, H.J., van Hattum, F.W.J.: Influence of waviness and curliness of fibres on mechanical properties of composites. Comput. Mater. Sci. 87, 1–11 (2014). doi:10.1016/j.commatsci.2014.01.061
Meguid, S., Sun, Y.: On the tensile and shear strength of nano-reinforced composite interfaces. Mater. Des. 25, 289–296 (2004). doi:10.1016/j.matdes.2003.10.018
Meguid, S.A., Wernik, J.M., Al Jahwari, F.: Toughening mechanisms in multiphase nanocomposites. Int. J. Mech. Mater. Des. 9, 115–125 (2013). doi:10.1007/s10999-013-9218-x
Mori, T., Tanaka, K.: Average stress in matrix and average elastic energy of materials with misfitting inclusions. Acta Metall. 21, 571–574 (1973). doi:10.1016/0001-6160(73)90064-3
Nasdala, L., Ernst, G.: Development of a 4-node finite element for the computation of nano-structured materials. Comput. Mater. Sci. 33, 443–458 (2005). doi:10.1016/j.commatsci.2004.09.047
Odegard, G.M., Gates, T.S., Wise, K.E., Park, C., Siochi, E.J.: Constitutive modeling of nanotube-reinforced polymer composites: modeling and characterization of nanostructured materials. Compos. Sci. Technol. 63, 1671–1687 (2003). doi:10.1016/S0266-3538(03)00063-0
Odegard, G.M., Frankland, S.-J.V., Gates, T.S.: Effect of nanotube functionalization on the elastic properties of polyethylene nanotube composites. AIAA J. 43, 1828–1835 (2005). doi:10.2514/1.9468
Park, C., Ounaies, Z., Watson, K.A., Crooks, R.E., Smith, J., Lowther, S.E., Connell, J.W., Siochi, E.J., Harrison, J.S., Clair, T.L.S.: Dispersion of single wall carbon nanotubes by in situ polymerization under sonication. Chem. Phys. Lett. 364, 303–308 (2002). doi:10.1016/S0009-2614(02)01326-X
Plimpton, S.: Fast parallel algorithms for short-range molecular dynamics. J. Comput. Phys. 117, 1–19 (1995). doi:10.1006/jcph.1995.1039
Qian, D., Dickey, E.C., Andrews, R., Rantell, T.: Load transfer and deformation mechanisms in carbon nanotube-polystyrene composites. Appl. Phys. Lett. 76, 2868–2870 (2000). doi:10.1063/1.126500
Qiu, Y.P., Weng, G.J.: On the application of Mori-Tanaka’s theory involving transversely isotropic spheroidal inclusions. Int. J. Eng. Sci. 28, 1121–1137 (1990). doi:10.1016/0020-7225(90)90112-V
Rahmat, M., Hubert, P.: Carbon nanotube-polymer interactions in nanocomposites: a review. Compos. Sci. Technol. 72, 72–84 (2011). doi:10.1016/j.compscitech.2011.10.002
Schadler, L.S., Giannaris, S.C., Ajayan, P.M.: Load transfer in carbon nanotube epoxy composites. Appl. Phys. Lett. 73, 3842 (1998). doi:10.1063/1.122911
Selmi, A., Friebel, C., Doghri, I., Hassis, H.: Prediction of the elastic properties of single walled carbon nanotube reinforced polymers: a comparative study of several micromechanical models. Compos. Sci. Technol. 67, 2071–2084 (2007). doi:10.1016/j.compscitech.2006.11.016
Shen, L., Li, J.: Transversely isotropic elastic properties of single-walled carbon nanotubes. Phys. Rev. B 69, 045414 (2004). doi:10.1103/PhysRevB.69.045414
Sobhani Aragh, B., Nasrollah Barati, A.H., Hedayati, H.: Eshelby–Mori–Tanaka approach for vibrational behavior of continuously graded carbon nanotube-reinforced cylindrical panels. Compos. Part B Eng. 43, 1943–1954 (2012). doi:10.1016/j.compositesb.2012.01.004
Spitalsky, Z., Tasis, D., Papagelis, K., Galiotis, C.: Carbon nanotube-polymer composites: chemistry, processing, mechanical and electrical properties. Prog. Polym. Sci. 35, 357–401 (2010). doi:10.1016/j.progpolymsci.2009.09.003
Srivastava, D., Wei, C., Cho, K.: Nanomechanics of carbon nanotubes and composites. Appl. Mech. Rev. 56, 215–230 (2003). doi:10.1115/1.1538625
Stuart, S.J., Tutein, A.B., Harrison, J.A.: A reactive potential for hydrocarbons with intermolecular interactions. J. Chem. Phys. 112, 6472–6486 (2000). doi:10.1063/1.481208
Tersoff, J.: Empirical interatomic potential for silicon with improved elastic properties. Phys. Rev. B 38, 9902–9905 (1988). doi:10.1103/PhysRevB.38.9902
Thostenson, E.T., Chou, T.-W.: On the elastic properties of carbon nanotube-based composites: modelling and characterization. J. Phys. Appl. Phys. 36, 573–582 (2003). doi:10.1088/0022-3727/36/5/323
Treacy, M.M.J., Ebbesen, T.W., Gibson, J.M.: Exceptionally high Young’s modulus observed for individual carbon nanotubes. Nature 381, 678–680 (1996). doi:10.1038/381678a0
Tsai, J.-L., Tzeng, S.-H., Chiu, Y.-T.: Characterizing elastic properties of carbon nanotubes/polyimide nanocomposites using multi-scale simulation. Compos. Part B Eng. 41, 106–115 (2010). doi:10.1016/j.compositesb.2009.06.003
Tunvir, K., Kim, A., Nahm, S.H.: The effect of two neighboring defects on the mechanical properties of carbon nanotubes. Nanotechnology 19, 065703 (2008). doi:10.1088/0957-4484/19/6/065703
van Gunsteren, W.F., Berendsen, H.J.C.: Computer simulation of molecular dynamics: methodology, applications, and perspectives in chemistry. Angew. Chem. Int. Ed. Engl. 29, 992–1023 (1990). doi:10.1002/anie.199009921
Verlet, L.: Computer “experiments” on classical fluids. I. Thermodynamical properties of Lennard-Jones molecules. Phys. Rev. 159, 98–103 (1967). doi:10.1103/PhysRev.159.98
Wagner, H.D., Lourie, O., Feldman, Y., Tenne, R.: Stress-induced fragmentation of multiwall carbon nanotubes in a polymer matrix. Appl. Phys. Lett. 72, 188–190 (1998). doi:10.1063/1.120680
Wang, Z., Colorad, H.A., Guo, Z.-H., Kim, H., Park, C.-L., Hahn, H.T., Lee, S.-G., Lee, K.-H., Shang, Y.-Q.: Effective functionalization of carbon nanotubes for bisphenol F epoxy matrix composites. Mater. Res. 15, 510–516 (2012). doi:10.1590/S1516-14392012005000092
Wernik, J.: Multiscale Modeling of Nano-reinforced Aerospace Adhesives (PhD). University of Toronto, Toronto, ON (2013)
Wernik, J.M., Meguid, S.A.: Atomistic-based continuum modeling of the nonlinear behavior of carbon nanotubes. Acta Mech. 212, 167–179 (2010). doi:10.1007/s00707-009-0246-4
Wernik, J.M., Meguid, S.A.: Multiscale micromechanical modeling of the constitutive response of carbon nanotube-reinforced structural adhesives. Int. J. Solids Struct. 51, 2575–2589 (2014). doi:10.1016/j.ijsolstr.2014.03.009
Wernik, J.M., Cornwell-Mott, B.J., Meguid, S.A.: Determination of the interfacial properties of carbon nanotube reinforced polymer composites using atomistic-based continuum model. Int. J. Solids Struct. 49, 1852–1863 (2012). doi:10.1016/j.ijsolstr.2012.03.024
Wong, E.W., Sheehan, P.E., Lieber, C.M.: Nanobeam mechanics: elasticity, strength, and toughness of nanorods and nanotubes. Science 277, 1971–1975 (1997). doi:10.1126/science.277.5334.1971
Xiao, T., Liu, J., Xiong, H.: Effects of different functionalization schemes on the interfacial strength of carbon nanotube polyethylene composite. Acta Mech. Solida Sin. 28, 277–284 (2015). doi:10.1016/S0894-9166(15)30014-8
Yang, X.-S.: Modelling heat transfer of carbon nanotubes. Model. Simul. Mater. Sci. Eng. 13, 893–902 (2005). doi:10.1088/0965-0393/13/6/008
Yang, L., Tong, L., He, X.: MD simulation of carbon nanotube pullout behavior and its use in determining mode I delamination toughness. Comput. Mater. Sci. 55, 356–364 (2012a). doi:10.1016/j.commatsci.2011.12.014
Yang, S., Yu, S., Kyoung, W., Han, D.-S., Cho, M.: Multiscale modeling of size-dependent elastic properties of carbon nanotube/polymer nanocomposites with interfacial imperfections. Polymer 53, 623–633 (2012b). doi:10.1016/j.polymer.2011.11.052
Yu, M.-F., Lourie, O., Dyer, M.J., Moloni, K., Kelly, T.F., Ruoff, R.S.: Strength and breaking mechanism of multiwalled carbon nanotubes under tensile load. Science 287, 637–640 (2000). doi:10.1126/science.287.5453.637
Zang, J.-L., Yuan, Q., Wang, F.-C., Zhao, Y.-P.: A comparative study of Young’s modulus of single-walled carbon nanotube by CPMD, MD and first principle simulations. Comput. Mater. Sci. 46, 621–625 (2009). doi:10.1016/j.commatsci.2009.04.007
Zeng, Q.H., Yu, A.B., Lu, G.Q.: Multiscale modeling and simulation of polymer nanocomposites. Prog. Polym. Sci. 33, 191–269 (2008). doi:10.1016/j.progpolymsci.2007.09.002
Zhou, M.: A new look at the atomic level virial stress: on continuum-molecular system equivalence. Proc. R. Soc. Math. Phys. Eng. Sci. 459, 2347–2392 (2003). doi:10.1098/rspa.2003.1127
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2016 Springer International Publishing Switzerland
About this chapter
Cite this chapter
Alian, A.R., Meguid, S.A. (2016). Multiscale Modeling of Nanoreinforced Composites. In: Meguid, S. (eds) Advances in Nanocomposites. Springer, Cham. https://doi.org/10.1007/978-3-319-31662-8_1
Download citation
DOI: https://doi.org/10.1007/978-3-319-31662-8_1
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-31660-4
Online ISBN: 978-3-319-31662-8
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)