Abstract
A digital image correlation procedure is developed to perform kinematic measurements on the surface of 316LN austenitic steel polycrystals. A sequence of images is acquired using a Scanning Electron Microscope (SEM) during in situ tensile tests for various mean grain sizes. To enable digital image correlation, a speckle pattern adapted to the microscopic scale is deposited onto the specimen surface by microlithography. The knowledge of the microstructure at the surface allows for kinematic measurements to be performed using an unstructured finite element mesh consistent with the grain boundaries. The same mesh is then used for the simulation of each tensile test on the experimental microstructure with the measured nodal displacements prescribed as boundary conditions. A crystal plasticity law is considered to simulate the observed strain heterogeneities. An inverse identification method is proposed for the determination of the sought constitutive parameters based on both the local displacement fields and the material homogenized behavior. The parameters associated with isotropic hardening at the grain level are thus identified.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
S. Leclercq, D. Lidbury, S. Van Dyck, D. Moinereau, A. Alamo, M.A. Al, PERFORM 60—prediction of the effects of radiation for reactor pressure vessel and in-core materials using multi-scale modelling—60 years foreseen plant lifetime. J. Nuclear Mater. 406(1), 193–203 (2010)
F. Roters, P. Eisenlohr, L. Hantcherli, D.D. Tjahjanto, T.R. Bieler, D. Raabe, Overview of constitutive laws, kinematics, homogenization and multiscale methods in crystal plasticity finite-element modeling: theroy, experiments, applications. Acta Materialia 58, 1152–1211 (2010)
T. Hoc, J. Crépin, L. Gélébart, A. Zaoui, A procedure for identifying the plastic behavior of single crystals from the local response of polycrystals. Acta Materialia 51(18), 5477–5488 (2003)
M.A. Sutton, N. Li, D.C. Joy, A.P. Reynolds, X. Li, Scanning electron microscopy for quantitative small and large deformation measurements part I: Sem imaging at magnifications from 200 to 10.000. Exp. Mech. 47(6), 775–787 (2007)
E. Héripré, M. Dexet, J. Crépin, L. Gélébart, A. Roos, M. Bornert, D. Caldemaison, Coupling between experimental measurements and polycrystal finite element calculations for micromechanical study of metallic materials. Int. J. Plast. 23(9), 1512–1539 (2007)
H. Lim, J.D. Carroll, C.C. Battaile, B.L. Boyce, C.R. Weinberger, Quantitative comparison between experimental measurements and CP-FEM predictions of plastic deformation in a tantalum oligocrystal. Int. J. Mech. Sci. 92, 98–108 (2015)
A. Guery, F. Latourte, F. Hild, S. Roux, Characterization of SEM speckle pattern marking and imaging distortion by digital image correlation. Meas. Sci. Technol. 25, 015401 (2014)
H. Leclerc, J.-N. Périé, S. Roux, F. Hild, Integrated digital image correlation for the identification of mechanical properties, MIRAGE 2009. LNCS 5496, 161–171 (2009)
Z. Tomičević, F. Hild, S. Roux, Mechanics-aided digital image correlation. J. Strain Anal. Eng. Des. 48, 330–343 (2013)
A. Guery, F. Hild, F. Latourte, S. Roux, Slip activities in FCC polycrystals determined by coupling DIC and crystal plasticity calculations. (2014)
S. Zaefferer, N.-N. Elhami, Theory and application of electron channelling contrast imaging under controlled diffraction conditions. Acta Materialia 75, 20–50 (2014)
L. Méric, P. Poubanne, G. Cailletaud, Single crystal modeling for structural calculations: part 1—model presentation. J. Eng. Mater. Tech. 113, 162–170 (1991)
M. Berveiller, A. Zaoui, An extension of the self-consistent scheme to plastically-flowing polycrystals. J. Mech. Phys. Solids 26, 325–344 (1979)
Y. Guilhem, S. Basseville, F. Curtit, J.-M. Stéphan, G. Cailletaud, Investigation of the effect of gran clusters on fatigue crack initiation in polycrystals. Int. J. Fatigue 32, 1748–1763 (2010)
F. Mathieu, H. Leclerc, F. Hild, S. Roux, Estimation of elastoplastic parameters via weighted FEMU and integrated-DIC. Exp. Mech. (2014). doi: 10.1007/s11340-014-9888-9
G. Besnard, F. Hild, S. Roux, “Finite-Element” displacement fields analysis from digital images: application to portevin-le chatelier bands. Exp. Mech. 46(6), 789–803 (2006)
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2016 The Society for Experimental Mechanics, Inc.
About this paper
Cite this paper
Guery, A., Latourte, F., Hild, F., Roux, S. (2016). Bridging Kinematic Measurements and Crystal Plasticity Models in Austenitic Stainless Steels. In: Bossuyt, S., Schajer, G., Carpinteri, A. (eds) Residual Stress, Thermomechanics & Infrared Imaging, Hybrid Techniques and Inverse Problems, Volume 9. Conference Proceedings of the Society for Experimental Mechanics Series. Springer, Cham. https://doi.org/10.1007/978-3-319-21765-9_5
Download citation
DOI: https://doi.org/10.1007/978-3-319-21765-9_5
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-21764-2
Online ISBN: 978-3-319-21765-9
eBook Packages: EngineeringEngineering (R0)