Abstract
Modern trucks have a reasonably optimised cab shape , and there exist several OEM and aftermarket devices for drag reduction for heavy trucks as well. To further reduce the aerodynamic drag major changes to the current layout of the vehicle are required, or the focus must be shifted from the cab and tractor trailer gap to other regions of the vehicle. The drag of the underbody, including wheel housings, wheels and engine compartment, represents a significant proportion of the aerodynamic drag and there has not been much investigation in this specific area on heavy trucks. To be able to reduce the fuel consumption and to fulfil the legislated emission standards for heavy trucks it is important to take all areas of the vehicle under consideration, and even though the individual improvements may be small, the total drag reduction will be substantial. In order to study the flow close to the vehicle underbody it is important to utilise the correct boundary conditions, that is, moving ground and rotating wheels. This work has focused on the flow in the front wheel housings. The flow field around the front wheels under the influence of ground simulation on a heavy truck of standard European configuration was investigated using numerical simulations. The in- and outflow to the wheel housing was located and the vortices originating from the front wheels were identified. This information was then used to identify which areas of the wheel housing having the greatest potential for aerodynamic improvements by changing the front wheel housing design. Furthermore, several wheel housing design parameters were defined, and their influence on the flow field and aerodynamic drag were investigated. Examples of these parameters are the shape of the wheel housing opening and implementation of wheel housing ventilation. It was found that there is potential for reducing the aerodynamic drag by applying these geometric changes to the wheel housing, and several of the configurations could be implemented on current production vehicles.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Lögdberg, O.: Turbulent boundary layer separation and control, Ph.D. thesis, KTH, Stockholm (2008)
Hjelm, L., Bergqvist, B.: European truck aerodynamics—a comparison between conventional and CoE truck aerodynamics and a look into future trends and possibilities. In: ECI—The Aerodynamics of Heavy Vehicles II: Trucks, Buses and Trains (2007)
Wiedemann, J.: The influence of ground simulation and wheel rotation on aerodynamic drag optimization—potential for reducing fuel consumption. In: SAE Paper 960672 (1996)
Elofsson, P., Bannister, M.: Drag reduction mechanisms due to moving ground and wheel rotation in passenger cars. In: SAE Paper 2002-01-0531 (2002)
Wäschle, A.: Numerische und experimentelle Untersuchung des Einflusses von drehenden Rädern auf die Fahrzeugaerodynamik, Dissertation, Expert Verlag, Stuttgart (2006)
Camosy, M.: Advanced experimental methods for the analysis and aerodynamic design of heavy vehicles. In: ECI—Aerodynamics of Heavy Vehicles II: Trucks, Buses and Trains, Conference Presentation (2007)
Sebben, S.: Numerical simulations of a car underbody: effect of front-wheel deflector. In: SAE Paper 2004-01-1307 (2004)
Modlinger, F., Demuth, R., Adams, N.: New directions in the optimization of the flow around wheels and wheel arches. In: 7th MIRA International Vehicle Aerodynamics Conference (2008)
Cogotti, A.: Aerodynamic characteristics of car wheels, International Journal of Vehicle Design, Technological Advances in Vehicle Design Series, SP3, Impact of Aerodynamics on Vehicle Design, pp. 173–196 (1983)
Fabijanic, J.: An experimental investigation of wheel-well flows. In: SAE Paper 960901 (1996)
Morelli, A.: A new aerodynamic approach to advanced automobile basic shapes. In: SAE Paper 2000-01-0491 (2000)
Söderblom, D., Elofsson, P., Hjelm, L., Löfdahl, L.: Heavy vehicle wheel housing flows—a parametric study. In: SAE Paper 2009-01-1169 (2009)
Söderblom, D., Elofsson, P., Hjelm, L., Löfdahl, L.: Flow field investigation of the wheel housing opening shape on a heavy truck using CFD. In: 8th MIRA International Vehicle Conference (2010)
Acknowledgments
The authors would like to acknowledge Vinnova and Energimyndigheten for funding the project, and Chalmers Computational Center for Science and Engineering (C3SE) and Gridcore AB for providing computational resources. Furthermore, Stephen Conway, Guillaume Mercier and Kamran Noghabai at Scania and the Sebastien Gautier at EXA GmbH should be acknowledged for software support and providing guidelines for the case setup.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2016 Springer International Publishing Switzerland
About this paper
Cite this paper
Söderblom, D., Elofsson, P., Hjelm, L., Löfdahl, L. (2016). Wheel Housing Aerodynamics on Heavy Trucks. In: Dillmann, A., Orellano, A. (eds) The Aerodynamics of Heavy Vehicles III. ECI 2010. Lecture Notes in Applied and Computational Mechanics, vol 79. Springer, Cham. https://doi.org/10.1007/978-3-319-20122-1_13
Download citation
DOI: https://doi.org/10.1007/978-3-319-20122-1_13
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-20121-4
Online ISBN: 978-3-319-20122-1
eBook Packages: EngineeringEngineering (R0)