Abstract
In a realistic bridge design code, the design live loads should be based on actual traffic loads, as discussed in Chap. 1. In the past, the information about the actual traffic loads on highway bridges was obtained from truck surveys, in which the trucks are stopped for measurement and weighing on ‘static’ weighing scales. During the past few decades, however, the information about the truck loads is collected while the trucks are moving at normal speeds. Some of the weighing-in-motion (WIM) scales are installed in the pavement. In other WIM systems, a highway bridge is used for the weighing-in-motion of the trucks; this latter system is referred to herein as the bridge WIM (BWIM) system, and the system installed in the pavement as simply the WIM system. The WIM systems are significantly more expensive and are expected to be more accurate than the BWIM systems.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Agarwal AC, Bakht B (1988) Error analysis of weighing in motion by highway bridges. Transportation Forum, Roads and Transportation Association of Canada, vol 3(3). pp 31–40, Ottawa
Arroyo M, Hannachi M, Siegert D, Jacob B (2010) Extreme traffic load effects on medium span bridges. In: Clemente P, DeStefano A (eds) WIM (Weigh-in-Motion) load capacity and bridge performance. International Society for Health Monitoring of Intelligent Infrastrures, Politico di Torino, pp 9–14, Italy
ASTM E1318-02 (2002) Standard specification for highway Weigh-in-Motion (WIM) systems with user requirements and test methods. ASTM International, West Conshohocken, Pennsylvania
Bakht B, Mufti AA, Tadros G, Eden R, Mourant G (2006) Weighing-in-motion of truck axle weights by Japanese reaction force method. In: 3rd international conference on bridge maintenance, safety and management, held in Porto, 16–19 July 2006, pp 981–982
Bianchi G, Sorrentino R (2007) Electronic filter simulation & design. McGraw-Hill, New York
Christenson R, Bakulski S, McDonnell AMH (2011) Establishment of a dual-purpose bridge health monitoring and weigh-in-motion system for a steel girder bridge. In transportation research board 90th annual meeting (No. 11–1598). Washington, DC
Dowling J, Gonzalez A, Obrien EJ (2010) Monitoring of traffic loads and bridge performance using a bridge weigh-in-motion system. In: Clemente P, DeStefano A (eds) International society for health monitoring of intelligent infrastrures. Politico di Torino, pp 107–113, Italy
González A, Rowley C, OBrien EJ (2008) A general solution to the identification of moving vehicle forces on a bridge. Int J Numer Methods Eng 75(3):335–354
Harman DJ (1984) A study of commercial vehicles and their multiple presence, OJTCRP project no. 23141. University of Western Ontario, Faculty of Engineering Science, London, Ontario
Helmi K, Bakht B, Mufti A (2014) Accurate measurement of gross vehicle weight through bridge weighing-in-motion. A case study. J Civ Struct Heal Monit 4:195–208
Heywood RJ (1991) Bridge applications of WIM data. In: Heywood RJ (ed) Proceedings of the AUSTROADS bridges conference. Austroads, Haymarket, pp 139–150
Jacob B, O’Brien E, Jehaes S (2002) COST 323, weigh-in-motion of road vehicles. Laboratoire Central des Ponts et Chausées, Paris
Jaeger LG, Bakht B (1989) Bridge analysis by microcomputer. McGraw Hill, New York
Moses F (1979) Weigh-in-motion system using instrumented bridges. ASCE Transp Eng J 106(TE3):233–249
Quilligan M, Karoumi R, O’Brien EJ (2002) Development and testing of a 2-dimensional multi-vehicle Bridge-WIM algorithm. In: Third international conference on Weigh-in-Motion (ICWIM3), Florida, USA
Rowley CW et al (2009) Experimental testing of a moving force identification bridge weigh-in-motion algorithm. Exp Mech 49(5):743–746
Scott G (1987) Weighing-in-motion technology – status CULWAY in Australia. Australian research board seminar on road traffic data collection using weighing-in-motion, Melbourne
Wall CJ, Christenson RE, McDonnell AMH, Jamalipour A (2009) A non-intrusive bridge weigh-in-motion system for a single span steel girder bridge using only stain measurements. Report no. CT-2251-03-09-5. Connecticut Department of Transportation, Bureau of engineering and construction, office of research and materials
Yamada K, Ojio T (2003) Bridge weigh-in-motion system using reaction force method. In: Proceedings of the international workshop on structural health monitoring of bridges/colloquium on bridge vibration’03, Japan Society of Civil Engineers, pp 269–276
Znidaric A, Kalin J, Lavric I (2002) Bridge weigh-in-motion measurements on short slab bridges without axle detectors. In: Third international conference on Weigh-in-Motion (ICWIM3),Florida, USA
Author information
Authors and Affiliations
Rights and permissions
Copyright information
© 2015 Springer International Publishing Switzerland
About this chapter
Cite this chapter
Bakht, B., Mufti, A. (2015). Bridge Weighing-in-Motion. In: Bridges. Springer, Cham. https://doi.org/10.1007/978-3-319-17843-1_11
Download citation
DOI: https://doi.org/10.1007/978-3-319-17843-1_11
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-17842-4
Online ISBN: 978-3-319-17843-1
eBook Packages: EngineeringEngineering (R0)