Abstract
This chapter highlights the impact of manufacturing errors on aircraft engines performance. The reader should use this chapter to identify the regions where Uncertainty Quantification should be used to improve the performance of a gas turbine.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Paniagua, G., Dénos, R., & Almeida, S. (2004). Effect of the hub endwall cavity flow on the flow-field of a transonic high-pressure turbine. Journal of Turbomachinery, 126(4), 578–586.
Dudgeon, E.H. (1994). Agard, agard-AR-320.
Schnell, R., Lengyel-Kampmann, T., & Nicke, E. (2014). On the impact of geometric variability on fan aerodynamic performance, unsteady blade row interaction, and its mechanical characteristics. Journal of Turbomachinery, 136, 091005-1.
Ghenaiet, A. (2012). Study of sand particle trajectories and erosion into the first compression stage of a turbofan. Journal of Turbomachinery, 134(5).
Tabakoff, W. (1986). Study of single stage axial flow compressor performance deterioration. American Society of Mechanical Engineers, Fluids Engineering Division (Publication) FED, 37, 95–100.
Balan, C., & Tabakoff, W. (1984). Axial flow compressor performance deterioration. AIAA Paper.
Ghenaiet, A., Tan, S. C., & Elder, R. L. (2005). Prediction of an axial turbomachine performance degradation due to sand ingestion. Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy, 219(4), 273–287.
Klinner, J., Hergt, A., & Willert, C. (2014). Experimental investigation of the transonic flow around the leading edge of an eroded fan airfoil. Experiments in Fluids, 55(9).
Giebmanns, A., Backhaus, J., & Frey, C. (2013). Compressor leading edge sensitivities and analysis with an adjoint flow solver. In Proceedings of the ASME Turbo Expo (Vol. 6 A).
Giebmanns, A., Schnell, R., & Steinert, W. (2012). Analyzing and optimizing geometrically degraded transonic fan blades by means of 2D and 3D simulations and cascade measurements. In Proceedings of the ASME Turbo Expo (Vol. 8, pp. 279–288).
Goodhand, M. N., Miller, R. J., & Lung, H. W. (2012). The sensitivity of 2D compressor incidence range to in-service geometric variation. In Proceedings of the ASME Turbo Expo (Vol. 8, pp. 159–170).
Goodhand, M. N., & Miller, R. J. (2011). Compressor leading edge spikes: A new performance criterion. Journal of Turbomachinery, 133(2).
Elmstrom, M. E., Millsaps, K. T., & Hobson, G. V. (2011). Impact of nonuniform leading edge coatings on the aerodynamic performance of compressor airfoils. Journal of Turbomachinery, 133(4).
Wheeler, A. P. S., Sofia, A., & Miller, R. J. (2009). The effect of leading-edge geometry on wake interactions in compressors. Journal of Turbomachinery, 131(4), 1–8.
Lamb, C. T., & Darmofal, D. L. (2004). Performance-based geometric tolerancing of compressor blades. In Proceedings of the ASME Turbo Expo (Vol. 5 A, pp. 203–210).
Garzon, V. E., & Darmofal, D. L. (2004). On the aerodynamic design of compressor airfoils for robustness under geometric uncertainty. Proceedings of the ASME Turbo Expo (Vol. 5 A, pp. 191–202).
Caguiat, D. E. (2003). Rolls royce/allison 501-K gas turbine antifouling compressor coatings evaluation. Journal of Turbomachinery, 125(3), 482–488.
Sakulkaew, S., Tan, C. S., & Donahoo, E. (2013). Compressor efficiency variation with rotor tip gap from vanishing to large clearance. Journal of Turbomachinery, 135(3).
Freeman, C. (1985). Tip clearance effects in axial turbomachines. In C. H. Sieverding (Ed.), VKI LS 1985-05, April 15–18. Von Karman Institute for Fluid Dynamics.
Suder, K. L., Chima, R. V., & Strazisar, A. J. (1995). The effect of adding roughness and thickness to a transonic axial compressor rotor. Transactions—ASME: Journal of Turbomachinery, 117(4), 491–505.
Gbadebo, S. A., Hynes, T. P., & Cumpsty, N. A. (2004). Influence of surface roughness on three-dimensional separation in axial compressors. In Proceedings of the ASME Turbo Expo 2004 (Vol. 5 A, pp. 471–481).
Syverud, E., Brekke, O., & Bakken, L. E. (2007). Axial compressor deterioration caused by saltwater ingestion. Journal of Turbomachinery, 129(1), 119–126.
Morini, M., Pinelli, M., Spina, P. R. (2010). Computational fluid dynamics simulation of fouling on axial compressor stages. Journal of Engineering for Gas Turbines and Power, 132(7).
Curlett, B. P. (1991). The aerodynamic effect of fillet radius in a low speed compressor cascade. NASA Technical Memorandum, 105347.
Salvadori, S., Montomoli, F. & Martelli, F. (2011). Aerothermal study of the unsteady flow field in a transonic gas turbine with inlet temperature distortions. Journal of Turbomachinery, 133(3).
Montomoli, F., Massini, M., & Salvadori, S. (2011). Geometrical uncertainty in turbomachinery: tip gap and fillet radius. Computers & Fluids, 46(1), 362–368.
Massini, M., Miller, R. J., & Hodson, H. P. (2011). A new intermittent aspirated probe for the measurement of stagnation quantities in high temperature gases. Journal of Turbomachinery, 133(4) .
Ames, F. E., & Moffat, R. J. (1990). Effects of simulated combustor turbulence on boundary layer heat transfer. American Society of Mechanical Engineers, Heat Transfer Division, (Publication) HTD, 138, 11–17.
Krishnamoorthy, V., Pai, B. R., & Sukhatme, S. P. (1988). Influence of upstream flow conditions on the heat transfer to nozzle guide vanes. Journal of Turbomachinery, 110(3), 412–416.
Krishnamoorthy, V., & Sukhatme, S. P. (1989). Effect of free-stream turbulence on gas turbine blade heat transfer. Journal of Turbomachinery, 111(4), 497–501.
Mehendale, A. B., Ekkad, S. V., & Han, J. (1994). Mainstream turbulence effect on film effectiveness and heat transfer coefficient of a gas turbine blade with air and CO2 film injection. International Journal of Heat and Mass Transfer, 37(17), 2707–2714.
Hall, B. F., Chana, K. S., & Povey, T.(2014). Design of a nonreacting combustor simulator with swirl and temperature distortion with experimental validation. Journal of Engineering for Gas Turbines and Power, 136(8).
Salvadori, S., Riccio, G., & Insinna, M. (2012). Analysis of combustor/vane interaction with decoupled and loosely coupled approaches. In Proceedings of the ASME Turbo Expo (Vol. 8, pp. 2641–2652).
Bunker, R. S. (2009). The effects of manufacturing tolerances on gas turbine cooling. Journal of Turbomachinery, 131(4), 1–11.
Moeckel, C. W., Darmofal, D. L., and Kingston, T. R. (2007) Toleranced designs of cooled turbine blades through probabilistic thermal analysis of manufacturing variability. In Proceedings of the ASME Turbo Expo (Vol. 5, pp. 1179–1191).
Sundaram, N., & Thole, K. A. (2007). Effects of surface deposition, hole blockage, and thermal barrier coating spallation on vane end wall film cooling. Journal of Turbomachinery, 129(3), 599–607.
Bohn, D., & Krewinkel, R. (2006). The effects of unintentional deviations due to manufacturing of cooling holes and operation on transpiration cooling efficiency. In Proceedings of the ASME Turbo Expo, (Vol. 3, part A, pp. 689–699).
Jovanovic, M. B., de Lange, H. C., & van Steenhoven, A. A. (2008). Effect of hole imperfection on adiabatic film cooling effectiveness. International Journal of Heat and Fluid Flow, 29(2), 377–386.
Jovanovic, M. B., de Lange, H. C., & van Steenhoven, A. A. (2006). Influence of hole imperfection on jet cross flow interaction. International Journal of Heat and Fluid Flow, 27(1), 42–53.
Jovanovic, M. B., De Lange, H. C., & Van Steenhoven, A. A. (2005). Influence of laser drilling imperfection on film cooling performances. In Proceedings of the ASME Turbo Expo (Vol. 3, part A, pp. 285–292).
Saumweber, C., & Schulz, A. (2012). Effect of geometry variations on the cooling performance of fan-shaped cooling holes. Journal of Turbomachinery, 134(6).
Larson, F., R., & Miller, J. (1952). A time temperature relationship for rupture and creep stresses. Transaction of ASME, 74, 765–775.
Vázquez, R., & Torre, D. (2013). The effect of surface roughness on efficiency of low pressure turbines. In Proceedings of the ASME Turbo Expo (Vol. 6 A).
Hourmouziadis, J. (1989). Aerodynamic design of low pressure turbines. AGARD Lecture Series (pp. 8.1–8.40).
Montomoli, F., Hodson, H., & Haselbach, F. (2010). Effect of roughness and unsteadiness on the performance of a new low pressure turbine blade at low Reynolds numbers. Journal of Turbomachinery, 132(3).
Zhou, C., Hodson, H., & Himmel, C. (2013). The effects of trailing edge thickness on the losses of ultra-high lift LP turbine blades. In Proceedings of the ASME Turbo Expo (Vol. 6 A).
Torre, D., Vázquez, R., & Armañanzas, L. (2013). The effect of airfoil thickness on the efficiency of low-pressure turbines. Journal of Turbomachinery, 136(5).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Copyright information
© 2015 The Author(s)
About this chapter
Cite this chapter
Montomoli, F., Carnevale, M., D’Ammaro, A., Massini, M., Salvadori, S. (2015). Manufacturing and in Service Uncertainty and Impact on Life and Performance. In: Uncertainty Quantification in Computational Fluid Dynamics and Aircraft Engines. SpringerBriefs in Applied Sciences and Technology. Springer, Cham. https://doi.org/10.1007/978-3-319-14681-2_1
Download citation
DOI: https://doi.org/10.1007/978-3-319-14681-2_1
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-14680-5
Online ISBN: 978-3-319-14681-2
eBook Packages: EngineeringEngineering (R0)