Abstract
In this chapter, the supplemental passive energy dissipation devices, metallic or hysteretic dampers, frictional, viscoelastic and viscous (linear and non-linear) dampers, developed and studied over the years, are briefly described. For each type of device, the physical, mechanical and technological aspects are analysed by describing the construction, hysteretic behavior, physical models, advantages, and disadvantages. Then, the more appropriate mathematical laws to model their dynamic behavior, with particular reference to the viscous and viscoelastic, are described. Finally, a comparison between all the different types of device is reviewed and the main recommendations, reported in the international codes with specific reference to the viscous and viscoelastic, are explained.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Aiken, I.D., Kelly, J.M.: Earthquake simulator testing and analytical studies of two energy absorbing systems for multistory structures, Report No. UCB/EERC-90/03, University of California, Berkeley (1990)
Aiken, I.D., Nims, D., Whittaker, A., and Kelly, J.: Testing of passive energy dissipation systems. Earthquake Spectra, Vol. 9, No. 3, Earthquake Engineering Research Institute, California (1993)
Applied Technology Council (ATC) (1996) Seismic evaluation and retrofit of concrete buildings, ATC-40, Redwood City, California
Applied Technology Council (ATC) (1997a) NEHRP commentary on the guidelines for the seismic rehabilitation of buildings, Report No. FEMA-273, Prepared for the Building Seismic Safety Council (BSSC) by the Applied Technology Council (ATC), Federal Emergency Management Agency (FEMA), Washington, D.C
Applied Technology Council (ATC) (1997b) NEHRP commentary on the guidelines for the seismic rehabilitation of buildings, Report No. FEMA-274, Prepared for the Building Seismic Safety Council (BSSC) by the Applied Technology Council (ATC), Federal Emergency Management Agency (FEMA), Washington, D.C
Applied Technology Council (ATC) (2000) Prestandard and Commentary for the Seismic Rehabilitation of Buildings, Report No. FEMA-356, Prepared for the Building Seismic Safety Council (BSSC) by the Applied Technology Council (ATC), Federal Emergency Management Agency (FEMA), Washington, D.C
ASCE (2005) Minimum design loads for buildings and other structures, ASCE/SEI 7–05, Reston, VA
Bergman, D.M., Hanson, R.D.: Viscoelastic mechanical damping devices tested at real earthquake displacements. Earthq. Spectra 9(3), 389–418 (1993)
Black, C.J., Makris, N., Aiken, I.: Component testing, seismic evaluation and characterization of buckling-restrained braces. J. Struct. Eng. 130(6), 880–894 (2004)
Building Seismic Safety Council (BSSC) (2004) NEHRP recommended provisions for seismic regulations for new buildings and other structures, 2003 Ed., Report Nos. FEMA-450/1 and FEMA-450/2, Prepared by the Building Seismic Safety Council (BSSC) for the Federal Emergency Management Agency (FEMA), Washington, D.C
Butterworth, J.J., Clifton, G.C.C.: Performance of hierarchical friction dissipating joints in moment resisting steel frames. In: Proceedings of 12 WCEE. http://www.iitk.ac.in/nicee/wcee/article/0718.pdf (2000)
Chang, K.C., Lai, M.L., Soong, T.T., Hao, D.S., Yeh, Y.C.: Seismic behavior and design guidelines for steel frame structures with added viscoelastic dampers, NCEER 93–0009. Buffalo, NY (1993)
Chang, K.C., Soong, T.T., Oh, S.-T., Lai, M.L.: Seismic behavior of steel frame with added viscoelastic dampers. ASCE 121(10), 1418–1426 (1995)
Charney, F.A., Mcnamara, R.J.: Use of damped mode shapes to assess the seismic performance of a 39-story building with viscous fluid dampers. In: Proceedings of 7th U.S. National Conference on Earthquake Engineering, EERI, Oakland, California (2002)
Charney, F.A., Mcnamara, R.J.: A comparison of methods for computing equivalent viscous damping ratios of structures with added viscous damping. J. Struct. Eng. 134(1), 32–44 (2008)
Constantinou, M.C., Symans, M.D.: Experimental study of seismic response of building with supplemental fluid dampers. J. Struct. Des. Tall Buildings 2(2), 93–132 (1993)
Constantinou, M.C., Soong, T.T., Dargush, G.F.: Passive energy dissipation systems for structural design and retrofit, Monograph n.1, Multidisciplinary Center for Earthquake Engineering Research, Buffalo, New York (1998)
Fierro, E.A., Perry, C.L.: San Francisco retrofit design using added damping and stiffness (ADAS) elements. In: Proceedings of ATC-17-1 Seminar on Seismic Isolation, Passive Energy Dissipation and Active Control, vol. 2, pp. 593–603. ATC, Redwood City, California (1993)
Filiatrault, A., Cherry, S.: Performance evaluation of friction damped braced frames under simulated Earthquake loads. Earthq. Spectra 3(1), 57–78 (1987)
Filiatrault, A., Cherry, S.: Efficient numerical modelling for seismic design of friction damped braced steel plane frames. Canadian J. Civ. Engrg. 16(3), 211–218 (1989)
Filiatrault, A., Cherry, S.: Seismic design spectra for friction-damped structures. J. Struct. Engrg. 116(5), 1334–1355 (1990)
Filiatrault, A., Tremblay, R., Wanitkorkul, A.: Performance evaluation of passive damping systems for the seismic retrofit of steel moment resisting frames subjected to near field ground motions. Earthq. Spectra 17(3), 427–456 (2001)
Fitzgerald, T.F., Anagnos, T., Goodson, M., Zsutty, T.: Slotted bolted connections in aseismic design for concentrically braced connections. Earthq. Spectra 5(2), 383–391 (1989)
Freeman, S.A.: Development and use of capacity spectrum method. In: Proceedings of 6th National Conference on Earthquake Engineering, Seattle (1998)
Fu, Y., Kasai, K.: Comparative study of frames using viscoelastic and viscous dampers. J. Struct. Eng. 124(5), 513–552 (1998)
Grigorian, C.E., Yang, T.S., Popov, E.P.: Slotted bolted connection energy dissipaters. Earthq. Spectra 9(3), 491–504 (1993)
Hertzberg, R.W.: Deformation and Fracture Mechanics of Engineering Materials. Wiley, New York (1983)
Hwang, J.S.: Seismic design of structures with viscous dampers, 高科技廠房震害防治研討會, 教育部科技顧問室, September. 30, 國立交通大學。, pp. 40–53 (2005)
Hwang, J.S., Huang, Y.N.: Seismic design of structures with viscous dampers, International training program for seismic design of structures, National Center for Research on Earthquake Engineering, 217–234 (2003)
Hwang, J.-S., Huang, Y.-N., Yi, S.-L., Ho, S.-Y.: Design formulations for supplemental viscous dampers to building structures. J. Struct. Eng. 134(1), 22–31 (2008)
International Code Council (ICC): International building code, 2006th edn. Delmar Cengage Learning, Clifton Park (2006)
Kelly, J.M., Skinner, R.I., Heine, A.J.: Mechanisms of energy absorption in special devices for use in earthquake resistant structures, Bull. N.Z. Soc. Earthq. Eng. 5(3), 63–88 (1972)
Kim, J., Choi, H.: Displacement-based design of supplemental dampers for seismic retrofit of a framed structure. J. Struct. Eng. ASCE 132(6), 873–883 (2006)
Kim, J.K., Choi, H.H., Min, K.W.: Performance-based design of added viscous dampers using capacity spectrum method. J. Earthquake Eng. 7(1), 1–24 (2003)
Kim, J.K., Seo, Y.I.: Seismic design of low-rise steel frames with buckling-restrained braces. Eng. Struct. 26(5), 543–551 (2004)
Kircher., C.A.: Seismic regulations for passive structural control systems-overview of United States codes. In: Proceedings of 2nd World Conference on Structural Controlo, Wiley, Chichester, U.K (1999)
Lee, D., Taylor, D.P.: Viscous damper development and future trends. Struct. Des. Tall. Build. 10(5), 311–320 (2001)
Lin, W.H., Chopra, A.K.: Earthquake response of elastic single-degree-of-freedom systems with non-linear viscoelastic dampers. J. Eng. Mech. 129(6), 597–606 (2003)
Lin, Y.Y., Tsai, M.H., Hwang, J.S., Chang, K.C.: Direct displacement-based design for building with passive energy dissipation systems. Eng. Struct. 25(1), 25–37 (2003)
Lobo, R.F., Bracci, J.M., Shen, K.L., Reinhorn, A.M., Soong, T.T.: Inelastic response of R/C structures with viscoelastic braces. Earthq. spectra 9(3), 419–446 (1993)
Makris, N.: Viscous heating of fluid dampers. I: small amplitude motions. J. Eng. Mech. 124(11), 1210–1216 (1998)
Makris, N., Roussos, Y., Whittaker, A.S., Kelly, J.M.: Viscous heating of fluid dampers. II: large amplitude motions. J. Eng. Mech 124, 1217–1223 (1998)
Miller, A.K.: Unified Constitutive Equations for Creep and Plasticity. Elsevier Applied Science, London (1987)
Miyamoto, H.K., Determan, L., Gilani, A., Hanson, R.: Seismic rehabilitation of historic concrete structure with fluid viscoelastic dampers. In: Proceedings of 72nd Annual Structural Engineers Association of California Convention, SEAOC, Sacramento, California (2003)
National Fire Protection Association, (NFPA) (2006) NFPA 5000: Building construction and safety code, Quincy, Mass
Nims, D.K., Richter, P.J., Bachman, R.E.: The use of the energy dissipating restraint for seismic hazard mitigation. Earthq. spectra 9(3), 467–489 (1993)
Ozdemir, H.: Non-linear transient dynamic analysis of yelding structures. Ph. D. Dissertation, University of California, Berkeley, CA (1976)
Pall, A.S., Marsh, C.: Response of friction damped braced frames. J. Struct. Div. ASCE 108(ST6), 1313–1323 (1982)
Pall, A.S., Marsh, C., Fazio, P.: Friction joints for seismic control of large panel structures. J. Prestressed Concr. Inst. 25(6), 38–61 (1980)
Pavlou, E., Constantinou, M.C.: Response of elastic andinelastic structures with damping systems to near-field and soft-soil ground motions. Eng. Struct. 26(9), 1217–1230 (2004)
Ramirez, O.M., Constantinou, M.C., Kircher, C.A., Whittaker, A., Johnson, M., Gomez, J.D., Chrysostomou, C.Z. Development and evaluation of simplified procedures of analysis and design for structures with passive energy dissipation systems. Technical Report No. MCEER-00–0010, Revision, 1, Multidisciplinary Center for Earthquake Engineering Research, University of Buffalo, State University of New York, Buffalo, New York (2001)
Ross, D., Ungar, E.E., Kerwin, E.W.: Damping of plate flexural vibrations by means of viscoelastic laminar structural damping. ASME, New York (1959)
Seleemah, A., Constantinou, M.C.: Investigation of seismic response of buildings with linear and non-linear fluid viscous dampers. Report No. NCEER 97-0004, National Center for Earthquake Engineering Research, State University of New York at Buffalo, Buffalo, New York (1997)
Skinner, R.I., Kelly, J.M., Heine, A.J.: Histeresis dampers for earthquake-resistant structures. Earthq. Eng. Struct. Dynam. 3, 287–296 (1975)
Soong, T.T., Dargush, G.F.: Passive Energy Dissipation Systems in Structural Engineering. Wiley, Chichester (1997)
Soong, T.T., Spencer, B.F. Jr: Supplemental energy dissipation: state of the art and state of the practice, Eng. Struct. 24, 243–259 (2002)
Structural Engineers Association of California (SEAOC) (1999) Recommended lateral force requirements and commentary, Appendix I, Sacramento, California
Sullivan, T.J., Calvi, G.M., Priestley, M.J.N., Kowalski, M.J.: The limitations and performances of different displacement based design methods. J. Earthq. Eng. 7(1), 201–241 (2003)
Symans, M.D., Constantinou, M.C.: Passive fluid viscous damping systems for seismic energy dissipation. ISET J. Earthq. Technol. 35(4), 185–206 (1998)
Symans, M.D., Charney, F.A., Whittaker, A.S., Constantinou, M.C., Kicher, C.A., Johnson, M.W., McNamara, R.J.: Energy dissipation system for seismic applications: current practise and recent developments. J. Struct. Eng. 134(1), 3–21 (2008)
Tehrani, P., Maalek, S., The use of passive dampers and conventional strengthening methods for the rehabilitation of an existing steel structure. In: 4th International Conference on Earthquake Engineering Taipei, Taiwan, n.133 (2006)
Tsopelas, P., Okamoto, S., Constantinou, M.C., Ozaki, D., Fujii, S.: NCEER-TAISEI Corporation research program on sliding seismic isolation systems for bridges—Experimental and analytical study of systems consisting of sliding bearings, rubber restoring force devices and fluid dampers. Report No. NCEER 94–0002, National Center for Earthquake Engineering Research, State University of New York at Buffalo, Buffalo, New York (1994)
Wada, A., Saeki, E., Takeuchi, T., Watanabe, A.: Development of Unbonded Brace in Nippon Steel’s Unbonded Braces (promotional document), pp. 1–16. Nippon Steel Corporation Building Construction and Urban Development Division, Tokyo (1998)
Wen, Y.K.: Method for random vibration of hysteretic systems. J. Engrg. Mech. Div. 102(2), 249–263 (1976)
Whittaker, A.S., Aiken, I.D., Bergman, D., Clark, P.W., Cohen, J., Kelly, J.M., Scholl, R.E.: Code requirements for design and implementation of passive energy dissipation systems. In: Proceedings of ATC-17–1 Seminar on Seismic Isolation, Passive Energy Dissipation and Active Control, vol. 2, pp. 497–508. ATC, Redwood City, California (1993)
Whittaker, A.S., Bertero, V., Alonso, J., and Thompson C.: Earthquake simulator testing of steel plate added damping and stiffness elements, Report No. UCB/EERC-89/02, Earthquake Engineering Research Center, University of California, Berkeley (1989)
Whittaker, A.S., Bertero, V.V., Thompson, C.L., Alonso, L.J.: Seismic testing of steel-plate energy dissipating devices. Earthq. Spectra 7(4), 563–604 (1991)
Xia, C., Hanson, R.D.: Influence of ADAS element parameters on building seismic response, J. Struct. Eng. ASCE 118(7), 1903–1918 (1992)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Copyright information
© 2014 Springer International Publishing Switzerland
About this chapter
Cite this chapter
Castaldo, P. (2014). Passive Energy Dissipation Devices. In: Integrated Seismic Design of Structure and Control Systems. Springer Tracts in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-319-02615-2_2
Download citation
DOI: https://doi.org/10.1007/978-3-319-02615-2_2
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-02614-5
Online ISBN: 978-3-319-02615-2
eBook Packages: EngineeringEngineering (R0)