Zusammenfassung
In diesem Kapitel werden wir Verfahren behandeln zur Bestimmung der Traglast starr-plastischer Kontinua von einer, zwei und drei Dimensionen. Drähte, Balken und Rahmen gehören zur ersten Gruppe, Membranen, Platten und Schalen zur zweiten.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Preview
Unable to display preview. Download preview PDF.
Literatur
Siehe W. Prager, General Theory of Limit Design, Sektionsvortrag, 8. Internat. Kongr. Theor. Angew. Mech., Istanbul, 1952.
R. von Mises, Mechanik der plastischen Formänderung von Kristallen, Z. angew. Math. Mech. 8, 161–185 (1928).
G. I. Taylor, A Connection Between the Criterion of Yield and the Strain-Ratio Relationship in Plastic Solids, Proc. Roy. Soc. [A] 191, 441–446 (1947).
R. Hill, A Variational Principle of Maximum Plastic Work in Classical Plasticity, Quart. J. Mech. appl. Math. 1, 18–28 (1948).
Die Begriffe wurden eingeführt durch D. C. Drucker, H. J. Greenberg und W. Prager, The Safety Factor of an Elastic-Plastic Body in Plane Strain, J. appl. Mech. 18, 371–378 (1951);
siehe auch W. Prager und P. G. Hodge, Jr., Theory of Perfectly Plastic Solids (New York 1951)
(ins Deutsche übertragen von F. Chmelka, Wien 1954), Kapitel VII, Ziffer 33, und Kapitel VIII, Ziffer 39, und D. C. Drucker, W. Prager und H. J. Greenberg, Extended Limit Design Theorems for Continuous Media, Quart. appl. Math. 9, 381–389 (1952).
R. Hill, On the State of Stress in a Plastic-Rigid Body at the Yield Point, Phil. Mag. [7] 42, 868–875 (1951).
Siehe zum Beispiel Hills in der vorhergehenden Fussnote aufgeführte Arbeit und E. H. Lee, On the Significance of the Limit Load Theorems for an Elastic-Plastic Body, Phil. Mag. [7] 43, 549–560 (1952);
R. Hill, Comments on Dr. Lee’s Paper, ibid. 560–561 (1952).
W. Prager, Discontinuous Fields of Plastic Stress and Flow, Allgemeiner Vortrag, 2. nat. Kongr. angew. Mech. (Ann Arbor, Michigan 1954); Proceedings (New York 1955), S. 21–32.
G. Kazinczy, Betonszemele (Budapest) 2, 68, 83, 101 (1914).
N. C. Kist, Inaugural-dissertation, Techn. Hochschule Delft, 1917;
siehe auch J. A. van den Broek, Theory of Limit Design (New York 1948).
J. F. Baker, A Review of Recent Investigations into the Behaviour of Steel Frames in the Plastic Range, J. Instn. Civ. Engrs. 31, 188–240 (1949);
J. F. Baker, The Design of Steel Frames, The Structural Engr. 27, 397–431 (1949).
H. J. Greenberg und W. Prager, On Limit Design of Beams and Frames, Brown Univ. Techn. Report No. A 18–1, Providence, R.I., USA., 1949;
H. J. Greenberg und W. Prager, On Limit Design of Beams and Frames,Proc. Amer. Soc. Civ. Engrs. 77, Separate No. 59 (1951);
H. J. Greenberg und W. Prager, On Limit Design of Beams and Frames, Trans. Amer. Soc. Civ. Engrs. 117, 447–484 (1952), einschliesslich Diskussion.
P. S. Symonds und B. G. Neal, Recent Progress in Plastic Methods of Structural Analysis, J. Franklin Inst. 252, 383–407, 469–492 (1951).
E.T. Onat und W. Prager, Limit Analysis of Arches, J. Mech. Phys. Solids 1, 77–89 (1953);
The Influence of Axial Forces on the Collapse Load of Frames, Proc. 1st Midwestern Conf. Solid Mechanics, Urbana, Ill., 1953, S. 40–42.
H. G. Hopkins und W. Prager, The Load Carrying Capacities of Circular Plates, J. Mech. Phys. Solids 2, 1–13 (1953).
K.W. Johansen, Brudlinieteorier (Kopenhagen 1943).
P. G. Hodge, Jr., The Rigid-Plastic Analysis of Symmetrically Loaded Cylindrical Shells, J.Appl.Mech. 21, 336–342 (1954).
P. G. Hodge, Jr., The Rigid-Plastic Analysis of Symmetrically Loaded Cylindrical Shells, J. Appl. Mech. 21, 336–342 (1954).
E. T. Onat, The Plastic Collapse of Cylindrical Shells Under Axially Symmetrical Loading, Quart. Appl. Math. 13, 63–72 (1955).
E. T. Onat und W. Prager, Limit Analysis of Shells of Revolution, Koninkl. Nederl. Akad. Wet., Proc. [B] 57, 534–548 (1954).
D.C. Drucker, Limit Analysis of Cylindrical Shells Under Axially-Symmetric Loading, Proc. 1st Midwestern Conf. Solid Mechanics, Urbana Ill., 1953), S. 158–163.
Der Verfasser ist den Herren Professor Dr. J. Foulkes und Dr. E. T. Onat für die Überlassung dieses Materials zu Dank verbunden.
R. M. Haythornthwaite und E. T. Onat, Brown University Report OOR-3172/4.
A. Kooharian, Proc. Amer. Concrete Inst. 49, 317 (1953).
Vgl. hierzu D. C. Drucker und W. Prager, Soil Mechanics and Plastic Analysis or Limit Design, Quart. appl. Math. 10, 157 (1952).
Author information
Authors and Affiliations
Rights and permissions
Copyright information
© 1955 Springer Basel AG
About this chapter
Cite this chapter
Prager, W. (1955). Traglastverfahren. In: Probleme der Plastizitätstheorie. Lehr- und Handbücher der Ingenieurwissenschaften. Birkhäuser, Basel. https://doi.org/10.1007/978-3-0348-6928-7_3
Download citation
DOI: https://doi.org/10.1007/978-3-0348-6928-7_3
Publisher Name: Birkhäuser, Basel
Print ISBN: 978-3-0348-6929-4
Online ISBN: 978-3-0348-6928-7
eBook Packages: Springer Book Archive