Abstract
One of the main challenges in applying thick-section high-strength steels (HSS) at arctic condition in offshore and maritime industry is to maintain a sufficient level of toughness to prevent brittle failure. An aspect that requires special attention is the through-thickness microstructural variation which may result in different local mechanical responses affecting the overall material’s fracture behaviour. This paper presents an experimental study combining microstructural investigation and sub-sized fracture toughness testing at −100 °C of different sections of 80 mm S690QL steel aimed to evaluate the effect of microstructure on cleavage fracture. In addition, different crack depth to width ratios (a/W) were used to investigate the constraint effect, while different notch orientations were applied to assess the effect of rolling orientation. Results show lower fracture toughness for the middle of the plate, which was attributed to the presence of large Nb-rich inclusions which may feature pre-existing cracks and/or defects in the inclusion/matrix interface and also often distributed as clusters. It was also observed that a/W ratio plays an important role in fracture toughness showing shallow-notched specimens with substantially higher fracture toughness than deep cracked specimens. Moreover, microstructural features such as inclusions aligned parallel to the pre-crack can ease the crack propagation and contribute to a reduction in fracture toughness.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Billingham J et al (2003) Review of the performance of high strength steels used offshore. http://www.hse.gov.uk/research/rrpdf/rr105.pdf
Morris Jr JW (1993) Steels: for low temperature applications. In: McPherson HD (ed) Encyclopedia of advanced materials. Pergamon Press, Oxford
Liu H, Zhang H, Li J (2018) Thickness dependence of toughness in ultra-heavy low-alloyed steel plate after quenching and tempering. Metals 8(628)
Popovich V, Richardson IM (2015) Fracture toughness of welded thick section high strength steels. Paper presented at the 144th TMS annual meeting, Orlando, Florida, 15–19 March 2015
Donato GHB, Ruggieri C (2006) Estimation procedure for J and CTOD fracture parameters using three-point bend specimens. Paper presented at the 6th international pipeline conference, Calgary, Alberta, 25–29 September 2006
NEN (2019) EN 10025-6: hot rolled products of structural steels—Part 6: technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
ASTM International. ASTM E112-13: standard test methods for determining average grain size
ASTM International (2016) ASTM E1245-03: standard practice for determining the inclusion or second-phase constituent content of metals by automatic image analysis
International Standard (2015) ISO 12135: metallic materials—unified method of test for the determination of quasistatic fracture toughness
Vieira I, De Moor E (2017) Tempering response of bainitic and martensitic microstructures. Paper presented at 3rd Pan American Materials Congress, San Diego, California, 26–2 February/March 2017
Pallaspuro S (2018) On the factors affecting the ductile-brittle transition in as-quenched fully and partially martensitic low-carbon steels. Ph.D. thesis, University of Oulu
da Costa e Silva ALV (2019) The effects of non-metallic inclusions on properties relevant to the performance of steel in structural and mechanical applications. J Mater Res Technol 8(2):2408–2422
Mandal SK (2014) Steel metallurgy—properties, specifications, applications. McGraw-Hill Education, India
Griffith AA, Ingram TG (1920) The phenomena of rupture and flow in solids. Philos Trans R Soc London, A
Walters CL et al (2013) Validation of the acceptability of 10 × 20 mm specimens for fracture toughness determination of high-strength steels. Paper presented at 32nd international conference on ocean, offshore and arctic engineering, Nantes, France, 9–14 June 2013
Namewaga T et al (2019) Effect of carbon content on toughness of tempered martensitic steels analysed by toughness prediction model. ISIJ Int 59(7):1337–1343
Chen JH, Cao R (2015) Micromechanism of cleavage fracture of metals. Elsevier
Yan W, Shan YY, Yang K (2007) Influence of TiN inclusions on the cleavage fracture behaviour of low-carbon microalloyed steels. Metall Mater Trans A 38A:1211–1222
Dawes MG, Cho G (1992) Shallow crack fracture mechanics toughness tests and applications: first international conference. Woodhead Publishing
Rak I (2016) CTOD toughness evaluation of hyperbaric repair welds made under severe conditions. Struct Integrity Life 16(3):171–178
Kirk MT, Doods RH (1993) J and CTOD estimation equations for shallow cracks in Si edge notch bend specimens. J Test Eval 21(4):228–238
Smith JA, Rolfe ST (1994) The effect of crack depth (a) and crack depth to width ratio (a/W) on the fracture toughness of A553-B steel. J Press Vessel Technol, 115–121
Acknowledgements
The authors of this work are grateful to our sponsors, which include Allseas Engineering, Dillinger, the Dutch Ministry of Defence, Lloyd’s Register and TNO. This work was carried out under the Micro-Tough research project number 16350, which is (partly) financed by the Netherlands Organization for Scientific Research (NWO).
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 The Minerals, Metals & Materials Society
About this paper
Cite this paper
Bertolo, V.M., Jiang, Q., Walters, C.L., Popovich, V.A. (2020). Effect of Microstructure on Cleavage Fracture of Thick-Section Quenched and Tempered S690 High-Strength Steel. In: Li, J., et al. Characterization of Minerals, Metals, and Materials 2020. The Minerals, Metals & Materials Series. Springer, Cham. https://doi.org/10.1007/978-3-030-36628-5_15
Download citation
DOI: https://doi.org/10.1007/978-3-030-36628-5_15
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-36627-8
Online ISBN: 978-3-030-36628-5
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)