Abstract
In an effort to improve vehicle fuel efficiency, aluminum (Al) alloys have been gaining upward momentum for use in automotive powertrain components such as engine blocks. Al alloys are lightweight and have good mechanical strength at engine operating temperatures; making them a suitable choice for engine block production. However, during the manufacturing process factors such as inhomogeneous cooling rates and/or coefficients thermal expansion mismatches in multi-material castings can lead to the development of residual stress. This is of particular concern for the relatively thin cylinder bridges, which are exposed to large thermo-mechanical loading during engine operation. The casting process used at Nemak for I6 engine block production does not utilise cast-in liners and therefore may be also be suitable for future mass-produced linerless blocks. This paper utilizes neutron diffraction and SEM/EDS to determine how the elimination of cast-in liners as well as a T7 heat treatment effects the magnitude of residual stress in cast Al (A319 type alloy) engine blocks. It was observed that the T7 treatment resulted in a significant reduction of the strain/stress in the Al cylinder bridge (up to ~50% of the radial stress at the top of the bridge). In addition, the absence of the cast-in Fe liners allowed for unrestricted natural contraction of the Al bridge; leading to a combination of low tension and moderate compression as compared to the typically high tensile stress.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
J. Davis & Associates. and ASM International. Handbook Committee.. ASM International, 1993.
J. Robinson and D. Tanner, “The Magnitude of Heat Treatment Induced Residual Stresses and the Thermal Stress Relief of Aluminium Alloys,” Mater. Sci. Forum, vol. 404–407, pp. 355–360, 2009.
A. Lombardi, C. Ravindran, D. Sediako, and R. MacKay, “Determining the Mechanism of In-Service Cylinder Distortion in Aluminum Engine Blocks with Cast-In Gray Iron Liners,” Metall. Mater. Trans. A Phys. Metall. Mater. Sci., vol. 45, no. 13, pp. 6291–6303, 2014.
B. Chen et al., “In situ neutron diffraction measurement of residual stress relaxation in a welded steel pipe during heat treatment,” Mater. Sci. Eng. A, 2014.
D. Lados, D. Apelian, and L. Wang, “Minimization of residual stress in heat-treated Al-Si-Mg cast alloys using uphill quenching: Mechanisms and effects on static and dynamic properties,” Mater. Sci. Eng. A, vol. 527, no. 13–14, pp. 3159–3165, 2010.
J. Rolph, A. Evans, A. Paradowska, M. Hofmann, M. Hardy, and M. Preuss, “Stress relaxation through ageing heat treatment - a comparison between in situ and ex situ neutron diffraction techniques,” Comptes Rendus Phys., vol. 13, no. 3, pp. 307–315, 2012.
L. Godlewski, X. Su, T. Pollock, and J. Allison, “The effect of aging on the relaxation of residual stress in cast aluminum,” Metall. Mater. Trans. A Phys. Metall. Mater. Sci., vol. 44, no. 10, pp. 4809–4818, 2013.
Lombardi A, Sediako D, Machin A, Ravindran C and MacKay R (2017) Effect of solution heat treatment on residual stress in Al alloy engine blocks using neutron diffraction, Mater. Sci. Eng. A, 697(May): 238–247.
Lombardi A, D’Elia F, Ravindran C, Sediako D, Murty B and MacKay R (2012) Interplay Between Residual Stresses, Microstructure, Process Variables and Engine Block Casting Integrity, Metall. Mater. Trans. A, 43(13): 5258–5270.
Byczynski G and Mackay R (2019) The nemak cosworth casting process latest generation, Shape Casting 7th International Symposium, Springer International Publishing: 179–185.
Stroh J, Piche A, Sediako D, Lombardi A, and Byczynski G (2019) The Effects of Solidification Cooling Rates on the Mechanical Properties of an A319 Inline-6 Engine Block, The Minerals, Metals & Materials Society (TMS), vol. Light Metals 2019: 505–512.
Sediako D, D’Elia F, Lombardi A, Machin A, Ravindran C, Hubbard C and Mackay R (2011) Analysis of Residual Stress Profiles in the Cylinder Web Region of an As-Cast V6 Al Engine Block with Cast-In Fe Liners Using Neutron Diffraction, SAE Int. J. Mater. Manuf., 4(1): 138–151.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 The Minerals, Metals & Materials Society
About this paper
Cite this paper
Stroh, J., Sediako, D., Byczynski, G., Lombardi, A., Paradowska, A. (2020). Stress Characterization of Bore-Chilled Sand Cast Aluminum Engine Blocks in As-Cast and T7 Condition with Application of Neutron Diffraction. In: Tomsett, A. (eds) Light Metals 2020. The Minerals, Metals & Materials Series. Springer, Cham. https://doi.org/10.1007/978-3-030-36408-3_21
Download citation
DOI: https://doi.org/10.1007/978-3-030-36408-3_21
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-36407-6
Online ISBN: 978-3-030-36408-3
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)