Abstract
Lightning strikes can have devastating effects to human beings. Not only direct strikes, connecting leaders, induced or touch voltages are dangerous, but also step voltages are an issue. Although touch voltages are more critical in terms of mortality rate, in case of step voltages the involved area on ground can be quite large. This is the reason why in half of all cases, where lightning injures human beings, step voltages are responsible. To overcome this threat, the grounding system plays a major roll, when the lightning current should be diverted into ground. An inadequate grounding system may not only lead to a high ground potential rise, it may also lead to high step voltages in direct vicinity to the structure to be protected. However, when a grounding system is planned, step voltages are not considered in detail, because calculation of step voltages is quite time consuming. Some regulations are given for placing down conductors, because the largest ground potential rise exists at the point where the lightning current enters ground. Standards also give information on grounding rod arrangements or grounding rings as well as some simple equations, from which an assembled low frequency grounding resistance can be derived. Nowadays step voltages are calculated using complex simulation tools. Hereby different effects can be taken into account, like soil ionization, travelling waves, dispersion or even complex soil layers. However, most of the time these effects are neglected, because when considering a worst case, soil ionization for instance leads to smaller grounding resistances and in consequence to a lower step- or touch voltage. In this work a new approach is presented, in which an analytical consideration is used to describe a complex grounding system that consists of electric conductors of certain radii. This method has been implemented in a MATLAB algorithm and is able to calculate step voltages on ground level very fast, in a couple of milliseconds. This enables the user to plan a grounding system more efficiently, because the user has a direct response on the step voltage, when a grounding element is adjusted. Because the solution is based on analytical expressions, the method can also give reference information to stationary simulation tools. In this work an overview on the methodology is given, as well as a verification and some examples showing the full potential of this new methodology.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
IEC 62305-3:2010: Protection against lightning – Part 3: Physical damage to structures and life hazard (2010)
IEC 61936-1:2010+AMD1:2014 Consolidated Version: Power installations exceeding 1 kV a.c. – Part 1: Common rules (2014)
Sunde, E.D.: Earth Conduction Effects in Transmission Systems. Dover Publications Inc., New York (1949)
Liew, A.C., Darveniza, M.: Dynamic model of impulse characteristics of concentrated earths. IET Proc. Inst. Electr. Eng. 121, 123–135 (1974)
Suchanek, S., Hinrichsen, V., Brocke, R., Müller, K.P.: Investigations of earth termination systems with respect to optimised step voltages. In: IEEE International Conference on Lightning Protection (2012)
Suchanek, S., Hinrichsen, V., Gao, J., Munteanu, I., Brocke, R., Müller, K.P.: Simulation of earth termination systems under consideration of step voltages. In: XIV International Conference on Atmospheric Electricity (2011)
Comsol Multiphysics GmbH: Comsol Multiphysics Reference Manual (2018)
CST Computer Simulation Technology GmbH: CST STUDIO SUITE Help (2018)
Heidler, F., Stimper, K. Blitz und Blitzschutz. VDE Verlag (2009)
Hannig, M.: Calculation of the assembled grounding resistance from complex grounding systems by using analytical considerations only. In: International Conference on High Voltage Engineering (2018)
IEC 60050-195:1998/AMD1:2001: International Electrotechnical Vocabulary (IEV) - Part 195: Earthing and protection against electric shock (1998)
Suchanek, S.: Untersuchungen an Blitzschutzerdungsanlagen unter besonderer Berücksichtigung der Schrittspannung, Dissertation (2014)
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 Springer Nature Switzerland AG
About this paper
Cite this paper
Hannig, M., Brocke, R., Hinrichsen, V. (2020). A New Approach in Calculation of Step Voltages for Complex Grounding Systems by Analytical Considerations Only. In: Németh, B. (eds) Proceedings of the 21st International Symposium on High Voltage Engineering. ISH 2019. Lecture Notes in Electrical Engineering, vol 598. Springer, Cham. https://doi.org/10.1007/978-3-030-31676-1_10
Download citation
DOI: https://doi.org/10.1007/978-3-030-31676-1_10
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-31675-4
Online ISBN: 978-3-030-31676-1
eBook Packages: EngineeringEngineering (R0)