Abstract
The results of an experimental study on crack-resistance of large scale compressed-bent reinforced concrete columns strengthened under initial load are represented in this paper. Structural performance of unstrengthened reference samples and jacketed samples under initial load of 30%, 50%, 70% and 90% of the bearing capacity of the reference samples was investigated. During the tests of the columns cracks pattern along the length of the columns, cracks length and width development were observed and recorded. Crack width vs Load graphs were plotted for the analysis of cracks development. Crack width at each loading stage was recorded to determine the critical crack. The load Nw when the critical crack reached the width of wmax = 0.3 mm (according to Eurocode-2: Design of Concrete Structures) was considered as a loss of serviceability of the column. Analyzing the increase of columns serviceability after reinforced concrete jacketing the conclusion was made that higher load level during strengthening results in the lover strengthening effect. The maximum increase in serviceability of the columns considering the ultimate crack width was achieved when the sample was jacketed without any initial loading and the minimum - for the samples jacketed under the load of 90% of their bearing capacity.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Al Saffar D, Alsaad A, Tayeh B (2019) Effect of internal curing on behavior of high performance concrete: an overview. Case Stud Constr Mater. https://doi.org/10.1016/j.cscm.2019.e00229
Al Sherrawi M, Lyashenko V, Edaan E, Sotnik L (2018) Corrosion as a source of destruction in construction. Int J Civ Eng Technol 9:306–314
Blikhars’kyi Z.Ya, Obukh Y (2018) Influence of the mechanical and corrosion defects on the strength of thermally hardened reinforcement of 35GS steel. Mater Sci 54. https://doi.org/10.1007/s11003-018-0183-2
Blikharskyy Y, Khmil R, Blikharskyy Z (2018a) Research of RC columns strengthened by carbon FRP under loading. Matec Web Conf 174:1–8. https://doi.org/10.1051/matecconf/201817404017
Blikharskyy Z, Brózda Kinga, Selejdak J (2018b) Effectivenes of strengthening loaded RC beams with FRCM system. Arch Civ Eng 64:3–13. https://doi.org/10.2478/ace-2018-0025
Blikharskyy Z, Selejdak J, Blikharskyy Y, Khmil Roman (2019) Corrosion of reinforce bars in RC constructions. Syst Saf Hum Tech Facil Environ 1:277–283. https://doi.org/10.2478/czoto-2019-0036
Blikharskyy Z, Vegera P, Vashkevych R, Shnal T (2018c) Fracture toughness of RC beams on the shear, strengthening by FRCM system. Matec Web Conf 183:02009. https://doi.org/10.1051/matecconf/201818302009
Bobalo T, Blikharskyy Y, Vashkevich R, Volynets M (2018) Bearing capacity of RC beams reinforced with high strength rebars and steel plate. Matec Web Conf 230:02003. https://doi.org/10.1051/matecconf/201823002003
Brózda K, Selejdak J, Koteš P (2017) The analysis of beam reinforced with FRP bars in bending. Procedia Eng 192:64–68. https://doi.org/10.1016/j.proeng.2017.06.011
Fadhil B, Al-Rumaithi A, Al-Sherrawi M (2018) Properties of reactive powder concrete with different types of cement. Int J Civ Eng Technol 9:1313–1321
Khmil R, Tytarenko R, Blikharskyy Y, Vegera P (2018) Development of the procedure for the estimation of reliability of reinforced concrete beams, strengthened by building up the stretched reinforcing bars under load. East Eur J Enterp Technol 5/7(95):32–42. https://doi.org/10.15587/1729-4061.2018.142750
Kos Ž, Gotal Dmitrović L, Klimenko E (2017) Developing a model of a strain (deformation) of a damaged reinforced concrete pillar in relation to a linear load capacity. Tech J 11(4):150–154. https://hrcak.srce.hr/190990
Krainskyi P, Blikharskyy Y, Khmil R, Blikharskyy Z (2018a) Experimental study of the srengthening effect of reinforced concrete columns jacketed under service load level. Matec Web Conf 183:1–5. https://doi.org/10.1051/matecconf/201818302008
Krainskyi P, Blikharskyy Y, Khmil R, Vegera P (2018b) Influence of loading level on the bearing capacity of RC columns strengthened by jacketing. Matec Web Conf 230:02013. https://doi.org/10.1051/matecconf/201823002013
Kramarchuk A, Ilnytskyy B, Lytvyniak O, Grabowski A (2019) The increase of seismic stability for existing industrial buildings. AIP Conf Proc 2077:020029. https://doi.org/10.1063/1.5091890
Selejdak J, Khmil R, Blikharskyy Z (2018) The influence of simultaneous action of the aggressive environment and loading on strength of rc beams. Matec Web of Conf 183:1–6. https://doi.org/10.1051/matecconf/201818302002
Sobol K, Blikharskyy Z, Petrovska N, Terlyha V (2014) Analysis of structure formation peculiarities during hydration of oil-well cement with zeolitic tuff and metakaolin additives. Chem Chem Technol 8(4):461–465. https://doi.org/10.23939/chcht08.04.461
Tayeh B, Bakar BH, Megat J, Megat A, Voo Y (2013) Evaluation of bond strength between normal concrete substrate and ultra high performance fiber concrete as a repair material. Procedia Eng 54:554–563. https://doi.org/10.1016/j.proeng.2013.03.050
Vegera P, Vashkevych R, Blikharskyy Z (2018) Fracture toughness of RC beams with different shear span. Matec Web Conf 174:1–8. https://doi.org/10.1051/matecconf/201817402021
Zhang Q, Mol’kov YV, Sobko YM, Blikhars’kyi YZ, Khmil RE (2015) Specific fracture energy of thermally hardened reinforcement. Mater Sci 50(6):824–829. https://doi.org/10.1007/s11003-015-9789-9
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 Springer Nature Switzerland AG
About this paper
Cite this paper
Krainskyi, P., Blikharskyy, Y., Khmil, R., Vegera, P. (2020). Crack Resistance of RC Columns Strengthened by Jacketing. In: Blikharskyy, Z., Koszelnik, P., Mesaros, P. (eds) Proceedings of CEE 2019. CEE 2019. Lecture Notes in Civil Engineering , vol 47. Springer, Cham. https://doi.org/10.1007/978-3-030-27011-7_25
Download citation
DOI: https://doi.org/10.1007/978-3-030-27011-7_25
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-27010-0
Online ISBN: 978-3-030-27011-7
eBook Packages: EngineeringEngineering (R0)