Abstract
Based on geometric modeling and FEM, it is developed a technique for choosing the values of geometrical parameters of a threaded turning tool (rake angle, clearance angle, inclination angle of the cutting edge). This technique depends on the allowable values of kinematic rake and clearance angles at different points of the cutting edge and reliability characteristics of the threaded connection—fatigue strength and contact pressure in the thread. Using this technique, it is reasonable to use tools with an uncorrected profile and a negative value of the static rake angle at the nose point −10° for turning the pin thread of the tubing with a diameter of 114 mm, which is made of difficult-to-machine steel. The calculated values of the kinematic rake angles (−4.4°…−5.5°) indicate improved cutting conditions. Fatigue strength of the threaded connection almost does not change, but in order to avoid gaps in the connection, the coupling thread must be made by taking into account the difference in the flank angles of the pin and coupling.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Gurevich, J.L., Gorohov, M.V., Zaharov, V.I., et al.: Cutting conditions for hard-to-machine material: reference book, 2nd edn. Engineering technology, Moscow (1986)
Panchuk, V., Onysko, O., Medvid, I.: Technology of the oil and gas drill pipe connector manufacturing with low-permeability level of the drilling mud in its screw part. Acta Technica Corviniensis—Bull. Eng. XI, Fascicule 4 [October–December], pp. 47–54 (2018). http://acta.fih.upt.ro/pdf/2018-4/ACTA-2018-4-08.pdf
Onysko, O., Psiuk, M.: Analysis to ensure the accuracy of the tool-joint tapered thread profile manufactured by lathe tool with tool face general provisions and set accuracy of installation. Bull. NTU “KhPI”. Series: Techniques in a machine industry 17(1239), 10–17 (2017). http://repository.kpi.kharkov.ua/handle/KhPI-Press/32616
Fromentin, G., Döbbeler, B., Lung, D.: Computerized simulation of interference in thread milling of non-symmetric thread profiles. Procedia CIRP 31, 496–501 (2015). https://doi.org/10.1016/j.procir.2015.03.018
Baizeau, T., Campocasso, S., Fromentin, G., Rossi, F., Poulachon, G.: Effect of rake angle on strain field during orthogonal cutting of hardened steel with c-BN tools. Procedia CIRP 31, 166–171 (2015). https://doi.org/10.1016/j.procir.2015.03.089
An, Q.L., Guo, G.G., Zheng, X.H., Chen, M., Liu, G., Zhang, Y.S.: Experimental study on cutting characteristics for buttress thread turning of 13%Cr stainless steel. Key Eng. Mater. 443, 262–267 (2010). https://doi.org/10.4028/www.scientific.net/KEM.443.262
Rezayi Khoshdarregi, M., Altintas, Y.: Generalized modeling of chip geometry and cutting forces in multi-point thread turning. Int. J. Mach. Tools Manuf. 98, 21–32 (2015). https://doi.org/10.1016/j.ijmachtools.2015.08.005
Saglam, H., Unsacar, F., Yaldiz, S.: Investigation of the effect of rake angle and approaching angle on main cutting force and tool tip temperature. Int. J. Mach. Tools Manuf. 46(2), 132–141 (2006). https://doi.org/10.1016/j.ijmachtools.2005.05.002
Chen, S., Li, Q., Zhang, Y., An, Q.: Finite element analysis of tooth load distribution on P-110S conic threaded connections. Int. J. Press. Vessels Pip. 88(2–3), 88–93 (2011). https://doi.org/10.1016/j.ijpvp.2011.01.004
Shahani, A.R., Sharifi, S.M.H.: Contact stress analysis and calculation of stress concentration factors at the tool joint of a drill pipe. Mater. Des. 30(9), 3615–3621 (2009). https://doi.org/10.1016/j.matdes.2009.02.022
Luo, S., Wu, S.: Effect of stress distribution on the tool joint failure of internal and external upset drill pipes. Mater. Des. 1980–2015(52), 308–314 (2013). https://doi.org/10.1016/j.matdes.2013.05.073
Kopei, V., Onysko, O., Panchuk, V.: Computerized system based on FreeCAD for geometric simulation of thread turning of oil and gas pipes. In: 6th International Conference of Applied Science (May 9–11, 2018, Banja Luka, Bosnia and Herzegovina). Book of Abstracts, pp. 108–108. University of Banja Luka, Banja Luka (2018)
FreeCAD Documentation: http://www.freecadweb.org/wiki/Main_Page. Last accessed 19 Nov 2018
Dhondt, G: The finite element method for three-dimensional thermomechanical applications. Wiley (2004). http://dx.doi.org/10.1002/0470021217
Sines, G.: Behavior of metals under complex static and alternating stresses. In: Sines, G., Waisman, J.L. (eds.) Metal Fatigue, pp. 145–169. McGraw-Hill, New York (1959)
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 Springer Nature Switzerland AG
About this paper
Cite this paper
Kopei, V., Onysko, O., Panchuk, V. (2020). The Application of the Uncorrected Tool with a Negative Rake Angle for Tapered Thread Turning. In: Ivanov, V., et al. Advances in Design, Simulation and Manufacturing II. DSMIE 2019. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-030-22365-6_15
Download citation
DOI: https://doi.org/10.1007/978-3-030-22365-6_15
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-22364-9
Online ISBN: 978-3-030-22365-6
eBook Packages: EngineeringEngineering (R0)