Abstract
This chapter presents analysis and optimization of machinability of Mild steel grade 350 while high speed drilling operation. Taguchi design of experiments (DoEs), analysis of variance (ANOVA) and other traditional methods were applied to optimize the input variables in order to minimise the circularity, cylindricity, diameter error and surface roughness of drilled holes. It was found that point angle was the highest contributor for the circularity, cylindricity and surface roughness of drilled holes. The circularity error was minimum at the low speed (584 rpm), low feed (0.15 mm/rev) and moderate point angle (125°). The cylindricity error of holes was minimised at the high speed (849 rpm), moderate feed (0.2 mm/rev) and moderate point angle (125°). The moderate speed, low feed and moderate point angle minimised surface roughness considerably. The interaction between speed and point angle had the maximum contribution to the diameter error of drilled holes. The diameter error was minimum at the moderate speed, low feed and moderate point angle.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Asiltürk I, Neşeli S (2012) Multi response optimisation of CNC turning parameters via Taguchi method-based response surface analysis. Measurement 45(4):785–794
Belluco W, De Chiffre L (2004) Performance evaluation of vegetable-based oils in drilling austenitic stainless steel. J Mater Process Technol 148(2):171–176
Brady GS et al (2002) Materials handbook: an encyclopedia for managers, technical professionals, purchasing and production managers, technicians and supervisors. McGraw-Hill handbooks. McGraw-Hill
Çaydaş U et al (2011) Performance evaluation of different twist drills in dry drilling of AISI 304 austenitic stainless steel. Mater Manuf Processes 26(8):951–960
Chajda J et al (2008) Coordinate measurement of complicated parameters like roundness, cylindricity, gear teeth or free-form surface. In: International conference of advanced manufacturing operations, Kranevo, 8
Chen W-C, Liu X-D (2000) Study on the various coated twist drills for stainless steels drilling. J Mater Process Technol 99(1):226–230
Çiçek A et al (2012) Performance of cryogenically treated M35 HSS drills in drilling of austenitic stainless steels. Int J Adv Manuf Technol 60(1):65–73
Clyde FC (2001) Coombs’ printed circuits handbook. McGraw-Hill Professional
Dolinšek S (2003) Work-hardening in the drilling of austenitic stainless steels. J Mater Process Technol 133(1):63–70
Endo H et al (2007) Accuracy estimation of drilled holes with small diameter and influence of drill parameter on the machining accuracy when drilling in mild steel sheet. Int J Mach Tools Manuf 47(1):175–181
Firouzdor V et al (2008) Effect of deep cryogenic treatment on wear resistance and tool life of M2 HSS drill. J Mater Process Technol 206(1):467–472
Geng H (2015) Manufacturing engineering handbook. McGraw Hill Professional
Haq AN et al (2008) Multi response optimization of machining parameters of drilling Al/SiC metal matrix composite using grey relational analysis in the Taguchi method. Int J Adv Manuf Technol 37(3–4):250–255
Hashmi K et al (2000) Fuzzy logic based data selection for the drilling process. J Mater Process Technol 108(1):55–61
Hayajneh MT (2001) Hole quality in deep hole drilling. Mater Manuf Processes 16(2):147–164
Islam MN, Pramanik A (2016) Comparison of design of experiments via traditional and Taguchi method. J Adv Manuf Syst 15(03):151–160
Kaplan Y et al (2014) Investigation of the effects of machining parameters on the thrust force and cutting torque in the drilling of AISI D2 and AISI D3 cold work tool steels
Kilickap E, Huseyinoglu M (2010) Selection of optimum drilling parameters on burr height using response surface methodology and genetic algorithm in drilling of AISI 304 stainless steel. Mater Manuf Processes 25(10):1068–1076
Kim D, Ramulu M (2004) Drilling process optimization for graphite/bismaleimide–titanium alloy stacks. Compos Struct 63(1):101–114
Kıvak T et al (2012) Taguchi method based optimisation of drilling parameters in drilling of AISI 316 steel with PVD monolayer and multilayer coated HSS drills. Measurement 45(6):1547–1557
Krishnamoorthy A et al (2012) Application of grey fuzzy logic for the optimization of drilling parameters for CFRP composites with multiple performance characteristics. Measurement 45(5):1286–1296
Kumar D et al (2012) Operational modeling for optimizing surface roughness in mild steel drilling using Taguchi technique. Int J Res Manag 2(3):66–77
Kurt M et al (2009) Application of Taguchi methods in the optimization of cutting parameters for surface finish and hole diameter accuracy in dry drilling processes. Int J Adv Manuf Technol 40(5–6):458–469
Lee B et al (1998) Modeling and optimization of drilling process. J Mater Process Technol 74(1–3):149–157
Min S et al (2001) Development of a drilling burr control chart for low alloy steel, AISI 4118. J Mater Process Technol 113(1):4–9
Montgomery DC (2017) Design and analysis of experiments. Wiley
Nomani J et al (2013) Machinability study of first generation duplex (2205), second generation duplex (2507) and austenite stainless steel during drilling process. Wear 304(1):20–28
Nomani J et al (2016) Investigation on the behavior of austenite and ferrite phases at stagnation region in the turning of duplex stainless steel alloys. Metall Mater Trans A 47(6):3165–3177
Nomani J et al (2017) Stagnation zone during the turning of Duplex SAF 2205 stainless steels alloy. Mater Manuf Process (just-accepted)
Park S (1996) Robust design and analysis for quality engineering. Boom Koninklijke Uitgevers
Pramanik A et al (2016) Accuracy and finish during wire electric discharge machining of metal matrix composites for different reinforcement size and machining conditions. Proc Inst Mech Eng Part B J Eng Manuf, 0954405416662079
Prasanna J et al (2014) Optimization of process parameters of small hole dry drilling in Ti–6Al–4V using Taguchi and grey relational analysis. Measurement 48:346–354
Ross PJ (1996) Taguchi techniques for quality engineering. McGraw-Hill International Editions
Routio M, Säynätjoki M (1995) Tool wear and failure in the drilling of stainless steel. J Mater Process Technol 52(1):35–43
Samuel G, Shunmugam M (2003) Evaluation of circularity and sphericity from coordinate measurement data. J Mater Process Technol 139(1–3):90–95
Samui P (2014) Determination of surface and hole quality in drilling of AISI D2 cold work tool steel using MPMR, MARS and LSSVM. J Adv Manuf Syst 13(04):237–246
Sultan A et al (2015) Chip formation when drilling AISI 316L stainless steel using carbide twist drill. Proc Manuf 2:224–229
Taguchi G (1987) System of experimental design: engineering methods to optimize quality and minimize cost. UNIPUB/Kraus Int. Pub, White Plains, NY
Tosun N (2006) Determination of optimum parameters for multi-performance characteristics in drilling by using grey relational analysis. Int J Adv Manuf Technol 28(5–6):450–455
Vankanti VK, Ganta V (2014) Optimization of process parameters in drilling of GFRP composite using Taguchi method. J Mater Res Technol 3(1):35–41
Yusoff N et al (2011) Taguchi’s parametric design approach for the selection of optimization variables in a refrigerated gas plant. Chem Eng Res Des 89(6):665–675
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 Springer Nature Switzerland AG
About this chapter
Cite this chapter
Pramanik, A., Basak, A.K., Islam, M.N., Dong, Y., Debnath, S., Vora, J.J. (2020). Optimization of Accuracy and Surface Finish of Drilled Holes in 350 Mild Steel. In: Gupta, K., Gupta, M. (eds) Optimization of Manufacturing Processes. Springer Series in Advanced Manufacturing. Springer, Cham. https://doi.org/10.1007/978-3-030-19638-7_3
Download citation
DOI: https://doi.org/10.1007/978-3-030-19638-7_3
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-19637-0
Online ISBN: 978-3-030-19638-7
eBook Packages: EngineeringEngineering (R0)