Abstract
Micro-EDM process has evidenced itself as a suitable micromachining process for micro-features that are difficult to be produced using conventional processes. However, special machining requirements are needed to be fulfilled for successful miniaturization of EDM process. High precision systems, generators producing small input energy pulses, flushing systems, etc., are the few special requirements. Effective debris removal has been the topic of concern for achieving high precision levels in micro-EDM and scientific community has therefore proposed several assisted micro-EDM processes. The present chapter briefs on magnetic-assisted micro-EDM process. The chapter begins with the introduction to EDM process and then elucidates on the principle of EDM and micro-EDM process. Characteristics of micro-EDM process are discussed next with subsequent discussion on working principle of magnetic-assisted micro-EDM process. The chapter finally terminates with the concluding remarks.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
K. Albinski, K. Musiol, A. Miernikiewicz, S. Labuz, M. Malota, The temperature of a plasma used in electrical discharge machining. Plasma Sources Sci. Technol. 5(4), 736 (1996)
D.M. Allen, A. Lecheheb, Micro electro-discharge machining of ink jet nozzles: optimum selection of material and machining parameters. J. Mater. Process. Technol. 58(1), 53–66 (1996)
J.C. Amson, Lorentz force in the molten tip of an arc electrode. Br. J. Appl. Phys. 16(8), 1169 (1965)
G.G. Boothroyd, Fundamentals of Machining and Machine Tools, 3rd edn. (CRC/Taylor and Francis, Boca Raton, FL, 2006)
A. Descoeudres, Characterization of EDM Plasmas (Ph. D. thesis, Ecole Polytechnique Federale De Lausanne, 2006)
S. Dhanik, S.S. Joshi, Modeling of a single resistance capacitance pulse discharge in micro-electro discharge machining. J. Manuf. Sci. Eng. 127(4), 759–767 (2005)
C. Gao, Z. Liu, A study of ultrasonically aided micro-electrical-discharge machining by the application of workpiece vibration. J. Mater. Process. Technol. 139(1–3), 226–228 (2003)
M. Ghoreishi, J. Atkinson, A comparative experimental study of machining characteristics in vibratory, rotary and vibro-rotary electro-discharge machining. J. Mater. Process. Technol. 120(1–3), 374–384 (2002)
E.W. Gray, J.R. Pharney, Electrode erosion by particle ejection in low-current arcs. J. Appl. Phys. 45(2), 667–671 (1974)
M.G. Haines, S.V. Lebedev, J.P. Chittenden, F.N. Beg, S.N. Bland, A.E. Dangor, The past, present, and future of Z pinches. Phys. Plasmas 7(5), 1672–1680 (2000)
F. Han, S. Wachi, M. Kunieda, Improvement of machining characteristics of micro-EDM using transistor type isopulse generator and servo feed control. Precis. Eng. 28(4), 378–385 (2004)
M.G. Her, F.T. Weng, Micro-hole maching of copper using the electro-discharge machining process with a tungsten carbide electrode compared with a copper electrode. Int. J. Adv. Manuf. Technol. 17(10), 715–719 (2001)
M.P. Jahan, Micro-electrical discharge machining, in Nontraditional Machining Processes (Springer, London, 2013), pp. 111–151
M.P. Jahan, Y. San Wong, M. Rahman, A comparative study of transistor and RC pulse generators for micro-EDM of tungsten carbide. Int. J. Precis. Eng. Manuf. 9(4), 3–10 (2008)
M.P. Jahan, Y.S. Wong, M. Rahman, A study on the quality micro-hole machining of tungsten carbide by micro-EDM process using transistor and RC-type pulse generator. J. Mater. Process. Tech. 209(4), 1706–1716 (2009)
V.K. Jain, Introduction to Micromachining (Alpha Science International Limited, Oxford, 2010)
C.C. Kao, A.J. Shih, Sub-nanosecond monitoring of micro-hole electrical discharge machining pulses and modeling of discharge ringing. Int. J. Mach. Tools Manuf. 46(15), 1996–2008 (2006)
C.C. Kao, A.J. Shih, S.F. Miller, Fuzzy logic control of microhole electrical discharge machining. J. Manuf. Sci. Eng. 130(6), 064502 (2008)
Z. Katz, C.J. Tibbles, Analysis of micro-scale EDM process. Int. J. Adv. Manuf. Technol. 25(9–10), 923–928 (2005)
M. Keidar, I. Beilis, R.L. Boxman, S. Goldsmith, 2D expansion of the low-density interelectrode vacuum arc plasma jet in an axial magnetic field. J. Phys. D Appl. Phys. 29(7), 1973 (1996)
K.S. Kim, Influence of a transverse magnetic field on arc root movements in a dc plasma torch: diamagnetic effect of arc column. Appl. Phys. Lett. 94(12), 121501 (2009)
M.K. Kiran, S.S. Joshi, Modeling of surface roughness and the role of debris in micro-EDM. J. Manuf. Sci. Eng. 129(2), 265–273 (2007)
P. KotalÃk, H. Nishiyama, An effect of magnetic field on arc plasma flow. IEEE Trans. Plasma Sci. 30(1), 160–161 (2002)
D. Kremer, J.L. Lebrun, B. Hosari, A. Moisan, Effects of ultrasonic vibrations on the performances in EDM. CIRP Ann. Manuf. Technol. 38(1), 199–202 (1989)
M. Kunieda, B. Lauwers, K.P. Rajurkar, B.M. Schumacher, Advancing EDM through fundamental insight into the process. CIRP Ann. Manuf. Technol. 54(2), 64–87 (2005)
B. Lauwers, J.P. Kruth, W. Liu, W. Eeraerts, B. Schacht, P. Bleys, Investigation of material removal mechanisms in EDM of composite ceramic materials. J. Mater. Process. Technol. 149(1–3), 347–352 (2004)
Y.C. Lin, B.H. Yan, Y.S. Chang, Machining characteristics of titanium alloy (Ti–6Al–4V) using a combination process of EDM with USM. J. Mater. Process. Technol. 104(3), 171–177 (2000)
C.T. Lin, H.M. Chow, L.D. Yang, Y.F. Chen, Feasibility study of micro-slit EDM machining using pure water. Int. J. Adv. Manuf. Technol. 34(1–2), 104–110 (2007)
K. Liu, B. Lauwers, D. Reynaerts, Process capabilities of Micro-EDM and its applications. ‎Int. J. Adv. Manuf. Technol. 47(1-4), 11-19 (2010)
H.S. Liu, B.H. Yan, F.Y. Huang, K.H. Qiu, A study on the characterization of high nickel alloy micro-holes using micro-EDM and their applications. J. Mater. Process. Technol. 169(3), 418–426 (2005)
S. Mahendran, R. Devarajan, T. Nagarajan, A. Majdi, A review of micro-EDM, in Proceedings of the International Multi Conference of Engineers and Computer Scientists, vol. 2
T. Masuzawa, State of the art of micromachining. CIRP Ann. Manuf. Technol. 49(2), 473–488 (2000)
M. Murali, S.H. Yeo, A novel spark erosion technique for the fabrication of high aspect ratio micro-grooves. Microsyst. Technol. 10(8–9), 628–632 (2004)
A. Muttamara, Y. Fukuzawa, N. Mohri, T. Tani, Probability of precision micro-machining of insulating Si3N4 ceramics by EDM. J. Mater. Process. Technol. 140(1–3), 243–247 (2003)
Y.P. Raizer, Gas Discharge Physics (1991)
K.P. Rajurkar, G. Levy, A. Malshe, M.M. Sundaram, J. McGeough, X. Hu, R. Resnick, A. DeSilva, Micro and nano machining by electro-physical and chemical processes. CIRP Ann. Manuf. Technol. 55(2), 643–666 (2006)
M.T. Richardson, Y.B. Gianchandani, Wireless monitoring of workpiece material transitions and debris accumulation in micro-electro-discharge machining. J. Microelectromech. Syst. 19(1), 48–54 (2010)
B. Shao, K.P. Rajurkar, Modelling of the crater formation in micro-EDM. Proc. CIRP 33, 376–381 (2015)
F.A. Soldera, F. Mücklich, on the erosion of material surfaces caused by electrical plasma discharging, in MRS Online Proceedings Library Archive (2004), p. 843
X. Song, W. Meeusen, D. Reynaerts, H. Van Brussel, Experimental study of micro-EDM machining performances on silicon wafer, in Micromachining and Microfabrication Process Technology VI, vol. 4174 (International Society for Optics and Photonics, 2000), pp. 331–340
R.J. Tayler, The influence of an axial magnetic field on the stability of a constricted gas discharge. Proc. Phys. Soc. Sect. B 70(11), 1049 (1957)
H. Tong, Y. Li, Y. Wang, Experimental research on vibration assisted EDM of micro-structures with non-circular cross-section. J. Mater. Process. Technol. 208(1–3), 289–298 (2008)
A.C. Wang, B.H. Yan, Y.X. Tang, F.Y. Huang, The feasibility study on a fabricated micro slit die using micro EDM. Int. J. Adv. Manuf. Technol. 25(1–2), 10–16 (2005)
J. Wang, Y.G. Wang, F.L. Zhao, Simulation of debris movement in micro electrical discharge machining of deep holes, in Materials Science Forum, vol. 626 (Trans Tech Publications, 2009), pp. 267–272
Z. Wansheng, W. Zhenlong, D. Shichun, C. Guanxin, W. Hongyu, Ultrasonic and electric discharge machining to deep and small hole on titanium alloy. J. Mater. Process. Technol. 120(1–3), 101–106 (2002)
F.T. Weng, M.G. Her, Study of the batch production of micro parts using the EDM process. Int. J. Adv. Manuf. Technol. 19(4), 266–270 (2002)
Y.S. Wong, M. Rahman, H.S. Lim, H. Han, N. Ravi, Investigation of micro-EDM material removal characteristics using single RC-pulse discharges. J. Mater. Process. Technol. 140(1–3), 303–307 (2003)
B.H. Yan, F.Y. Huang, H.M. Chow, J.Y. Tsai, Micro-hole machining of carbide by electric discharge machining. J. Mater. Process. Technol. 87(1–3), 139–145 (1999)
B.H. Yan, A.C. Wang, C.Y. Huang, F.Y. Huang, Study of precision micro-holes in borosilicate glass using micro EDM combined with micro ultrasonic vibration machining. Int. J. Mach. Tools Manuf. 42(10), 1105–1112 (2002)
S.H. Yeo, L.K. Tan, Effects of ultrasonic vibrations in micro electro-discharge machining of microholes. J. Micromech. Microeng. 9(4), 345 (1999)
S.H. Yeo, M. Murali, H.T. Cheah, Magnetic field assisted micro electro-discharge machining. J. Micromech. Microeng. 14(11), 1526 (2004)
S.H. Yeo, W. Kurnia, P.C. Tan, Electro-thermal modelling of anode and cathode in micro-EDM. J. Phys. D Appl. Phys. 40(8), 2513 (2007)
Z.Y. Yu, K.P. Rajurkar, H. Shen, High aspect ratio and complex shaped blind micro holes by micro EDM. CIRP Ann. Manuf. Technol. 51(1), 359–362 (2002)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Copyright information
© 2019 The Author(s), under exclusive license to Springer Nature Switzerland AG
About this chapter
Cite this chapter
Bhowmik, S., Zindani, D. (2019). Magnetic Field Assisted Micro-EDM. In: Hybrid Micro-Machining Processes. SpringerBriefs in Applied Sciences and Technology. Springer, Cham. https://doi.org/10.1007/978-3-030-13039-8_3
Download citation
DOI: https://doi.org/10.1007/978-3-030-13039-8_3
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-13038-1
Online ISBN: 978-3-030-13039-8
eBook Packages: EngineeringEngineering (R0)