Abstract
Weight minimization and global environmental policies on carbon content open a new research avenue towards materials and manufacturing processes in transport industries. Friction stir welding (FSW) process is a combination of frictional heating and stirring action where materials are joined in their solid state. In this study, a review has been made on the joining status of magnesium alloys to steel by using FSW. Present problems and future opportunities of magnesium to steel joining with the help of FSW are also stated. A case study has also been presented where the joint characteristics of AZ31B to AISI 304 sheets fabricated in lap configuration by FSW have been investigated by varying tool rotational speed (600, 1000, and 1800 rpm) and varying weld speed (40, 200, and 350 mm/min). A maximum weld joint efficiency of 79% of the AZ31B base alloy has been achieved with a parametric combination of 600 rpm and 350 mm/min.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Caiwang Tan, Liqun Li, Yanbin Chen, Wei Guo, “Laser-tungsten inert gas hybrid welding of dissimilar metals AZ31B Mg alloys to Zn coated steel,” Materials and Design 49 (2013) 766–773
Waled M. Elthalabawy, Tahir I. Khan, “Microstructural development of diffusion-brazed austenitic stainless steel to magnesium alloy using a nickel interlayer,” Materials Characterization 61 (2010) 703–712
Takehide Senuma, “Physical metallurgy of modern high strength steel sheets,” ISIJ International, Vol. 41 (2001), No. 6, pp. 520–532
Prakash Kumar Sahu, Sukhomay Pal, “Influence of metallic foil alloying by FSW process on mechanical properties and metallurgical characterization of AM20 Mg alloy,” Materials Science & Engineering A 684 (2017) 442–455
L. Liu (ed) (2010) Welding and Joining of Magnesium Alloys. Woodhead Publishing Limited, UK
V.K. Patel, S.D. Bhole and D.L. Chen, “Influence of ultrasonic spot welding on microstructure in a magnesium alloy,” Scripta Materialia 65 (2011) 911–914
V.K. Patel, S.D. Bhole, D.L. Chen, “Formation of zinc interlayer texture during dissimilar ultrasonic spot welding of magnesium and high strength low alloy steel,” Materials and Design 45 (2013) 236–240
W. Xua, D.L. Chena, L. Liub, H. Mori, Y. Zhoub, “Microstructure and mechanical properties of weld-bonded and resistance spot welded magnesium-to-steel dissimilar joints,” Materials Science and Engineering A 537 (2012) 11–24
L. Liu, L. Xiao, J.C. Feng, Y.H. Tian, S.Q. Zhou, and Y. Zhou, “The Mechanisms of Resistance Spot Welding of Magnesium to Steel,” Metallurgical and Materials Transactions A, Volume 41A, October 2010, 2651–2661
L. Liu, L. Xiao, D.L. Chen, J.C. Feng, S. Kim, Y. Zhou, “Microstructure and fatigue properties of Mg-to-steel dissimilar resistance spot welds,” Materials and Design 45 (2013) 336–342
G. Casalinoa, P. Guglielmi, V.D. Lorusso, M. Mortello, P. Peyre, D. Sorgente, “Laser offset welding of AZ31B magnesium alloy to 316 stainless steel,” Journal of Materials Processing Technology 242 (2017) 49–59
M. Wahba, S. Katayama, “Laser welding of AZ31B magnesium alloy to Zn-coated steel,” Materials and Design 35 (2012) 701–706
Xiaodong Qi, Gang Song, “Interfacial structure of the joints between magnesium alloy and mild steel with nickel as interlayer by hybrid laser-TIG welding,” Materials and Design 31 (2010) 605–609
Liming Liu, Xiaodong Qi, “Strengthening effect of nickel and copper interlayers on hybrid laser-TIG welded joints between magnesium alloy and mild steel,” Materials and Design 31 (2010) 3960–3963
Gang Song, Guangye An, Liming Liu, “Effect of gradient thermal distribution on butt joining of magnesium alloy to steel with Cu–Zn alloy interlayer by hybrid laser–tungsten inert gas welding,” Materials and Design 35 (2012) 323–329
Zhi Zeng, Xunbo Li, Yugang Miao, Gang Wu, Zijun Zhao, “Numerical and experiment analysis of residual stress on magnesium alloy and steel butt joint by hybrid laser-TIG welding,” Computational Materials Science 50 (2011) 1763–1769
L. M. Liu, X. Zhao, “Study on the weld joint of Mg alloy and steel by laser-GTA hybrid welding,” Materials Characterization 59 (2008) 1279–1284
Y. G. Miao, D. F. Han, J. Z. Yao & F. Li, “Microstructure and interface characteristics of laser penetration brazed magnesium alloy and steel,” Sci. Technol. Weld. Join., vol. 15, no. 2, pp. 97–103, 2010
C. W. Tan, Y. B. Chen, L. Q. Li & W. Guo, “Microstructure and properties of laser brazed magnesium to coated Steel,” Sci. Technol. Weld. Join., vol. 18, no. 6, pp. 466–472, 2013
Y. C. Chen and K. Nakata, “Effect of surface states of steel on microstructure and mechanical properties of lap joints of magnesium alloy and steel by friction stir welding,” Sci. Technol. Weld. Join., vol. 15, no. 4, pp. 293–298, 2010
Y. C. Chen and K. Nakata, “Effect of tool geometry on microstructure and mechanical properties of friction stir lap welded magnesium alloy and steel,” Mater. Des., vol. 30, no. 9, pp. 3913–3919, 2009
Y. C. Chen and K. Nakata, “Friction Stir Lap Welding of Magnesium Alloy and Zinc Coated Steel,” Mater. Trans., vol. 50, no. 11, pp. 2598–2603, 2009
S. Jana and Y. Hovanski, “Fatigue behaviour of magnesium to steel dissimilar friction stir lap joints,” Sci. Technol. Weld. Join., vol. 17, no. 2, pp. 141–145, 2012
S. Jana, Y. Hovanski, and G. J. Grant, “Friction stir lap welding of magnesium alloy to steel: A preliminary investigation,” Metall. Mater. Trans. A Phys. Metall. Mater. Sci., vol. 41, no. 12, pp. 3173–3182, 2010
H. Kasai, Y. Morisada, H. Fujii, “Dissimilar FSW of immiscible materials: Steel/magnesium,” Materials Science & Engineering A 624 (2015) 250–255
C. Schneider, T. Weinberger, J. Inoue, T. Koseki, and N. Enzinger, “Characterisation of interface of steel/magnesium FSW,” Sci. Technol. Weld. Join., vol. 16, no. 1, pp. 100–107, 2011
N. Afrin, D. L. Chen, X. Cao, and M. Jahazi, “Microstructure and tensile properties of friction stir welded AZ31B magnesium alloy,” Mater. Sci. Eng. A, vol. 472, no. 1–2, pp. 179–186, 2008
Z. Y. Ma, “Friction stir processing technology: A Review,” Metallurgical and Materials Transactions A, Volume 39A, March 2008, 642–658
A. Gerlich, P. Su, M. Yamamoto & T. H. North, “Material flow and intermixing during dissimilar friction stir welding,” Sci. Technol. Weld. Join., vol. 13, no. 3, pp. 254–264, 2008
P. Su, A. Gerlich, T.H. North, and G.J. Bendzsak, “Intermixing in dissimilar friction stir spot welds,” Metallurgical and Materials Transactions A, Volume 38A, March 2007, 584–595
Padmanaban, G. & Balasubramanian, V, “An experimental investigation on friction stir welding of AZ31B magnesium alloy,” Int J Adv Manuf Technol (2010) 49: 111. https://doi.org/10.1007/s00170-009-2368-1
Y. U. Sirong, Chen Xianjun, Huang Zhiqiu, Liu Yaohui, “Microstructure and mechanical properties of friction stir welding of AZ31B magnesium alloy added with cerium,” Journal of Rare Earths, Vol. 28, No. 2, Apr. 2010, p. 316
B. Ratna Sunil, G. Pradeep Kumar Reddy, A.S.N. Mounika, P. Navya Sree, P. Rama Pinneswari, I. Ambica, R. Ajay Babu, P. Amarnadh, “Joining of AZ31 and AZ91 Mg alloy by friction stir welding,” Journal of Magnesium and Alloys 3 (2015) 330–334
Stephan W. Kallee Wayne M. Thomas E. Dave Nicholas, “Friction stir welding of lightweight materials,” TWI Ltd, Cambridge, United Kingdom, pp 175–190
P. Cavaliere, P.P. De, “Marco Superplastic behaviour of friction stir processed AZ91 magnesium alloy produced by high pressure die cast,” Journal of Materials Processing Technology 184 (2007) 77–83
Yajie Li, Fengming Qin, Cuirong Liu and Zhisheng Wu, “A review: Effect of friction stir welding on microstructure and mechanical properties of magnesium alloys,” Metals 2017, 7(12), 524; https://doi.org/10.3390/met7120524
Y. Wei, J. Li, J. Xiong, F. Huang, and F. Zhang, “Microstructures and mechanical properties of magnesium alloy and stainless steel weld-joint made by friction stir lap welding,” Mater. Des., vol. 33, no. 1, pp. 111–114, 2012
ASTM E3-11(2017) Standard Guide for Preparation of Metallographic Specimens, ASTM International, West Conshohocken, PA, 2017, https://doi.org/10.1520/E0003-11R17
ASTM E407-07(2015)e1 Standard Practice for Microetching Metals and Alloys, ASTM International, West Conshohocken, PA, 2015, https://doi.org/10.1520/E0407-07R15E01
ASTM E384-17 Standard Test Method for Microindentation Hardness of Materials, ASTM International, West Conshohocken, PA, 2017, https://doi.org/10.1520/E0384-17
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 The Minerals, Metals & Materials Society
About this paper
Cite this paper
Sahu, S., Thorat, O., Mahto, R.P., Pal, S.K., Srirangam, P. (2019). A Review and Case Study on Mechanical Properties and Microstructure Evolution in Magnesium–Steel Friction Stir Welding. In: Joshi, V., Jordon, J., Orlov, D., Neelameggham, N. (eds) Magnesium Technology 2019. The Minerals, Metals & Materials Series. Springer, Cham. https://doi.org/10.1007/978-3-030-05789-3_17
Download citation
DOI: https://doi.org/10.1007/978-3-030-05789-3_17
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-05788-6
Online ISBN: 978-3-030-05789-3
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)