Abstract
The electric spark source is widely used in the fields of shallow surface exploration and earthquake prediction because of its environmental protection, rich spectrum and good consistency. However, most electric spark source is short of real time recording and control system for power parameters, so that its failure rate is quite high. This paper introduces a real-time power parameter recording system of electric spark source. It has the advantages of failure detection, fast fault location, and network extension. It can realize the remote control and monitoring, and has a strong popularization value.
This work was supported by the China National Petroleum Corporation essential research and strategic reserve technology research fund project (grant No. 2017Z-05).
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Pei, Y.L., Wang, K.Y., Liu, C.G., Li, X.S., Li, Z.G.: The sparker source charging technique. Ocean Technol. 26(03), 73–76 (2007)
Wu, X.L., Wang, J.M.: Research and Design of High Power Sparker. Yangtze University (2016)
Dai, X., Zhu, J., Haberman, M.R.: A focused electric spark source for non-contact stress wave excitation in solids. J. Acoust. Soc. Am. EL134(6), 513 (2013)
Fan, A.L., Sun, Y.H., Xu, Z., et al.: Single channel electric spark source and discharge experimental study. Advanced Technology of Electrical Engineering & Energy (2016)
Fan, A., Sun, Y., Yan, P., et al.: Design on a kind of multi-channel electric spark source system. In: Industrial Electronics and Applications, pp. 2391–2394. IEEE (2016)
Xu, X., Sun, Y., Fu, R., et al.: Development of the solid-state modular land electric spark source. High Volt. Appar. 53(4), 36–40 (2017)
Liu, Q., Shao, H., Zhang, Y.: Study on shock waves induced by electric spark discharge. China Science paper (2016)
Yang, Z.Y., Xu, Z.L.: The digital measurement and wireless data transmission for power parameter. Electr. Meas. Instrum. 42(472), 34–37 (2005)
Guo, Y., Fu, Z.X.: Frequency measurement of AC sampling and implementation of tracking phase-locked method. Zidonghua Yu Yiqi Yibiao 12(03), 17–19 (2002)
Ye, J.Z., Yin, X.: Development and application of the power load parameter recording and monitoring system. Comput. Eng. 32(05), 247–248 (2006)
Zhang, C., Zhang, C.J., Wu, X.G.: Design and implementation of simple SD card driven method in MCU system. 28(04), 479–481+499 (2011)
Li, S.Q., Dong, H.B., Li, R.S.: Design of SD memory card based on FatFs file system. Meas. Control Technol. 30(12), 79–80 (2011)
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2018 Springer Nature Switzerland AG
About this paper
Cite this paper
Luo, M., Zhang, H., Liu, Q., Xu, Y., Luo, C., Wang, Z. (2018). The Design of Real Time Recording System for Electric Spark Source Parameters Based on the Internet of Things. In: Chen, X., Sen, A., Li, W., Thai, M. (eds) Computational Data and Social Networks. CSoNet 2018. Lecture Notes in Computer Science(), vol 11280. Springer, Cham. https://doi.org/10.1007/978-3-030-04648-4_26
Download citation
DOI: https://doi.org/10.1007/978-3-030-04648-4_26
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-04647-7
Online ISBN: 978-3-030-04648-4
eBook Packages: Computer ScienceComputer Science (R0)