Abstract
Many materials found in nature are polymers. In fact, the basic molecular structure of all plant and animal life is similar to that of a synthetic polymer. Natural polymers include such materials as silk, shellac, bitumen, rubber, and cellulose. However, the majority of polymers or plastics used for engineering design are synthetic and often they are specifically formulated or “designed” by chemists or chemical engineers to serve a specific purpose. Other engineers (mechanical, civil, electrical, etc.) typically design engineering components from the available materials or, sometimes, work directly with chemists or chemical engineers to synthesize a polymer with particular characteristics. Some of the useful properties of various engineering polymers are high strength or modulus to weight ratios (light weight but comparatively stiff and strong), toughness, resilience, resistance to corrosion, lack of conductivity (heat and electrical), color, transparency, processing, and low cost. Many of the useful properties of polymers are in fact unique to polymers and are due to their long chain molecular structure. These issues will be discussed at length in the next chapter. In this chapter, focus will be on general characteristics, applications and an introduction to the mechanical behavior including elementary concepts of their inherent time dependent or viscoelastic nature.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Arman, B., A.S. Reddy, and G. Arya, “Viscoelastic Properties and Shock Response of Coarse-Grained Models of Multiblock versus Diblock Copolymers: Insights into Dissipative Properties of Polyurea.” Macromolecules, 45(7): p. 3247–3255, 2012.
Billmeyer, F.W., Textbook of Polymer Science, 3rd ed. JW, NY, 1984.
Brill, W.A., Basic Studies in Photoplasticity, Ph.D. Dissertation, Stanford University, 1965.
Brinson, H. F., “The Viscoelastic Behavior of a Ductile Polymer,” Deformation and Fracture of High Polymers, (H. Kausch, et al., Ed.’s.) Plenum Press, NY, 1973, p. 397–416.
Brinson, H. F., Renieri, M. P., and Herakovich, C. T., “Rate and Time Dependent Failure of Structural Adhesives,” Fracture Mechanics of Composites, STP 593, ASTM, Phil. PA, 1975, p. 177–199.
Brinson, H.F., “Digital Imaging Micro-Measurements of Mechanical Properties for Adhesive Joints and Polymer Matrix Composites”, Proceedings of the 10th International Conference on Experimental Mechanics, Plenary Lecture Volume, 1994.
Bucknall, C. B., Ayre, D. S. and Dijkstra, D. J. “Detection of rubber particle cavitation in toughened plastics using thermal contraction tests”, Polymer, v. 41, issue 15, 2000, p. 5937–5947.
Corleto, C.R., Bradley, W.L. and Brinson, H.F., “An Experimental Micro-mechanics Measurement Technique for Sub-Micron Domains”, Journal of Materials Science, 1996, Vol. 31, pp. 1803–1808.
Yongqi, S., W.L. Bradley, C. Corleto, and J. Tian, “Direct Measurement of Microscopic Strain Distribution in a Strain Field Near a Crack Tip,” Experimental Mechanics, Vol. 36, No. 3, pp. 193–198, 1996.
Crawford, R.J., Plastics Engineering, Pergamon, NY, 1992.
Das S, DF Cox, GL Wilkes, DB Klinedinst, I Yilgor, E Yilgor, FL Beyer, “Effect of symmetry and H-bond strength of hard segments on the structure-property relationships of segmented, nonchain extended polyurethanes and polyureas.” Journal of Macromolecular Science Part B-Physics, 46(5): p. 853–875, 2007.
Davidson, D.L. and Langford, J., “The Effect of Water Vapor on Fracture Tip Stress and strain Range Distribution and the Energy Required for Crack Propagation in Low-carbon Steel”, Int. J. Fract. 17. 257 (1981).
Hiel, C. C., Brinson, H. F. and Cardon, A.H., “The Nonlinear Viscoelastic Response of Resin Matrix Composites”, Composite Structures 2, Applied Science, NY, 1983, p. 271–281.
Hyer, M.W., Stress Analysis of Fiber-Reinforced Composite Materials, McGraw Hill, NY, 1998.
Kammers, A.D. and Daly, S, “Small-scale patterning methods for digital image correlation under scanning electron microscopy”, IOP Science, Meas. Sci. Technol. 22, 125501, 2011.
Kinloch, A.J., and Young, R.J., Fracture Behavior of Polymers, Applied Science, London, 1983; 2nd ed., 1995.
Peters, W.H. and Ranson, W.F.; “Digital imaging techniques in experimental stress analysis”, SPIE-Optical Engineering, Vol. 21 No. 3, 1982.
Rodriguez, F., “Principles of Polymer Systems”, 4th ed., Taylor and Francis, Washington, D.C., 1996.
Rybicky, E.F., and Kanninen, M.F., “The Effect of Different Behavior in Tension and Compression on the Mechanical Response of Polymeric Materials”. Deformation and Fracture of High Polymers, (H. Kausch, et al., Ed.’s.) Plenum Press, NY, 1973, p. 417–427.
Serpooshan, V. Zokaei, S. and Bagheri., R., “Effect of rubber particle cavitation on the mechanical properties and deformation behavior of high-impact polystyrene”, J. of Applied Polymer Science, Vol. 104, Issue 2, Pages 1110–1117, 2007.
Sutton, M.A., Wolters, W.J., Peters, W.H., Ranson, W.F. and McNeill, S.R., “Determination of displacements using an improved digital correlation method”; Image Vision Computing, 1 (3), 1983.
Tobolsky, A.V., Properties and Structure of Polymers, JW, NY, 1962.
Ward, I.M. and Hadley, D.W., An Introduction to the Mechanical Properties of Solid Polymers, JW, 1993.
Warner, S.B., Fiber Science, Prentice-Hall, NJ, 1995.
Author information
Authors and Affiliations
Rights and permissions
Copyright information
© 2015 Springer Science+Business Media New York
About this chapter
Cite this chapter
Brinson, H.F., Brinson, L.C. (2015). Characteristics, Applications and Properties of Polymers. In: Polymer Engineering Science and Viscoelasticity. Springer, Boston, MA. https://doi.org/10.1007/978-1-4899-7485-3_3
Download citation
DOI: https://doi.org/10.1007/978-1-4899-7485-3_3
Published:
Publisher Name: Springer, Boston, MA
Print ISBN: 978-1-4899-7484-6
Online ISBN: 978-1-4899-7485-3
eBook Packages: EngineeringEngineering (R0)