Abstract
In a typical boundary value problem, involving prescribed nominal traction rates on a part S F of the boundary surface, and prescribed velocities on the remainder S v , more than one mode of deformation may be possible when the applied load reaches a critical value. The lack of uniqueness of the deformation mode under given boundary conditions is commonly referred to as bifurcation, the current shape and mechanical state of the body being supposed to be given or previously determined. For a linear solid, in which the strain rate is a unique linear function of the stress rate during both loading and unloading, a bifurcation mode corresponds to an eigensolution of the field equations, and represents a mode quasi-statically possible under constant loads on S F and rigid constraints on S v In dealing with the conventional elastic/plastic solid, which is bilinear in the sense that the strain rate is related to the stress rate by separate linear functions for loading and unloading, it is convenient to introduce a linear comparison solid with identical boundary conditions (Section 1.5). While bifurcation in the linearized solid can occur under any given traction rates on S f and velocities on S v when the load becomes critical, bifurcation in the actual elastic/plastic solid would occur only under those traction rates for which there is no instantaneous unloading of the material that is currently plastic. The incremental theory of plasticity will be almost exclusively used in this chapter for the estimation of the critical load.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Preview
Unable to display preview. Download preview PDF.
References
Ades, CS. (1957), Bending Strength of Tubes in the Plastic Range, J. Aeronaut. Sci., 24, 505.
Akserland, E.L. (1965), Refinement of Upper Critical Loading of Pipe Bending Taking Account of Geometric Nonlinearity (in Russian), Mekhanika: Machinostroenic, Izv. Akad Nauk, SSSR, 4 123.
Alexander, J.M. (1960), An Approximate Analysis of the Collapse of Thin Cylindrical Shells Under Axial Loading, Quart. J. Mech. Appl. Math., 13, 10.
Ariaratnam, S.T. and Dubey, R.N. (1969), Instability in an Elastic-Plastic Cylindrical Shell Under Axial Compression, J. Appl. Mech., 36, 47.
Ashwell, D.G. (1959), On the Large Deflection of a Spherical Shell with an Inward Point Load, Proc. IUTAM on Theory of Thin Elastic Shells, Delft.
Babcock, CD. (1983), Shell Stability, J. Appl. Mech., 50, 935.
Baker, J.F., Horne, M.R., and Roderick, J.W. (1949), The Behaviour of Continuous Stanchions, Proc. Roy. Soc. London Ser. A., 198, 493.
Batdorf, S.R. (1949), Theories of Elastic-Plastic Buckling, J. Aeronaut. Sci., 16, 405.
Batterman, S. (1964), Load-Deflection Behaviour of Shells of Revolution, J. Engng. Mech. Div., Proc. ASCE, 90, EM6, 4167.
Batterman, S. (1965), Plastic Buckling of Axially Compressed Cylindrical Shells, AIAA J., 3, 316.
Batterman, S. (1968), Free Edge Buckling of Axially Compressed Cylindrical Shells, J. Appl. Mech., 35, 73.
Batterman, S. (1969), Plastic Buckling of an Externally Pressurized Complete Spherical Shell, J. Engng. Mech. Div., Proc. ASCE, 95.
Bijlaard, PP. (1949), Theory and Tests on the Plastic Stability of Plates and Shells, J. Aeronaut. Sci., 16, 529.
Bijlaard, PP. (1956), Theory of Plastic Buckling of Plates and Application to Simply Supported Plates Subjected to Bending or Eccentric Compression in Their Plane, J. Appl. Mech., 23, 27.
Brazier, L.G. (1926), On the Flexure of Thin Cylindrical Shells and Other Sections, Proc. Roy. Soc. London Ser. A, 116, 104.
Bushnell, D. (1982), Plastic Buckling of Various Shells, J. Pressure Vessels Technol., Trans. ASME, 104, 51.
Bushnell, D. and Galletly, G.D. (1974), Comparison of Test and Theory for Nonsymmetric Elastic-Plastic Buckling of Shells of Revolution, Int. J. Solids Struct., 10, 1271.
Chakrabarty, J. (1973), Plastic Buckling of Cylindrical Shells Under Uniform External Pressure, Z. Angew. Math. Phys., 24, 270.
Chakrabarty, J. (1998), Theory of Plasticity, 2nd ed., McGraw-Hill, Singapore.
Chawalla, E. (1937), Aussermittig Gedruckte Baustahlstabe mit Elastisch Eingespannten Enden und Verschieden Grossen Angriffschebeln, Der Stahlbau, 15, 49.
Chen, W.F. (1970), General Solution of Inelastic Beam-Column Problems, Engng. J. Mech. Div., Proc. ASCE, 96, EM4, 421.
Chen, W.F. and Astuta, T. (1976), Theory of Beam Columns, Vol. 1, McGraw-Hill, New York.
Corona, E. and Kyriakides, S. (1988), On the Collapse of Inelastic Tubes Under Combined Bending and Pressure, Int. J. Solids Struct., 24, 505.
Donneil, L.H. (1933), Stability of Thin Walled Tubes Under Torsion, NACA Report 479, pp. 1–24.
Dubey, R.N. (1978), On Bifurcation in Elastic-Plastic Solids, Nucl, Engng. Des., 49, 217.
El-Ghazaly, H.A. and Sherbourne, A.N. (1986), Deformation Theory for Elastic-Plastic Buckling Analysis of Plates Under Nonproportional Planar Loading, Computers and Structures, 22, 131.
Engesser, F. (1898), Z Ver. Deut. Ingr., 42, 927.
Flügge, W. (1932), Die Stabilität der Kreiszylinderschale, Ingenieur-Archiv, 3, 24.
Gellin, S. (1979), Effect of an Axisymmetric Imperfection on the Plastic Buckling of an Axially Compressed Cylindrical Shell, J. Appl. Mech., 46, 125.
Gellin, S. (1980), The Plastic Buckling of Long Cylindrical Shells Under Pure Bending, Int. J. Solids Struct., 16, 397.
Gerard, G. (1957), Handbook of Structural Stability, Part I, Buckling of Flat Plates, NACA TN3781.
Gerard, G. (1962), Introduction to Structural Stability Theory, McGraw-Hill, New York.
Gjelsvik, A. and Lin, G.S. (1985), Plastic Buckling of Plates with Edge Frictional Shear Effects, J. Engng. Mech. Div., Trans. ASCE, 113, 953.
Hamada, H. (1985), In-Plane Buckling of Circular Plates, Proc. J. Soc. Mech. Engrs., 51, 1928.
Hill, R. and Sewell, M.J. (1960), A General Theory of Inelastic Column Failure—I and II, J. Mech. Phys. Solids, 8, 105 and 112.
Hill, R. and Sewell, M.J. (1962), A General Theory of Inelastic Column Failure—III, J. Mech. Phys. Solids, 10, 185.
Horne, M.R. (1956), The Elastic-Plastic Theory of Compression Members, J. Mech. Phys. Solids, 4, 104.
Home, M.R. and Merchant, W. (1965), The Stability of Frames, Pergamon Press, Oxford, UK.
Hutchinson, J.W. (1972), On the Postbuckling Behavior of Imperfection Sensitive Structures in Plastic Range, J. Appl. Mech., 39, 155.
Hutchinson, J.W. (1973), Imperfection Sensitivity in the Plastic Range, J. Mech. Phys. Solids, 21, 163.
Hutchinson, J.W. (1974), Plastic Buckling, Adv. in Appl. Mech., 14, 67.
Inoue, T. and Kato, B. (1993), Analysis of Plastic Buckling of Steel Plates, Int. J. Solids Struct., 15, 567.
Ketter, R.L. (1961), Further Studies of the Strength of Beam Columns, J. Struct. Div., Proc. ASCE, 87, ST6, 135.
Leckie, RA. and Penny, R.K. (1968), Plastic Instability of Spherical Shells, in Engineering Plasticity (eds., J. Heyman and F.A. Leckie), Cambridge University Press, UK, p. 401.
Lee, L.H.N. (1962), Inelastic Buckling of Initially Imperfect Cylindrical Shells Subject to Axial Compression, J. Aeronaut. Sci., 29, 87.
Li, S. and Reid, S.R. (1992), The Plastic Buckling of Axial Compressed Square Tubes, J. Appl. Mech., 59, 276.
Lu, L.W. and Kamalvand, H. (1968), Ultimate Strength of Laterally Loaded Columns, J. Struct. Div., Proc. ASCE, 94, ST6, 1505.
Mamalis, A.G. and Johnson, W. (1983), Quasi-Static Crumpling of Thin-Walled Circular Cylinders and Frusta Under Axial Compression, Int. J. Mech. Sci., 25, 713.
Needleman, A. (1975), Post-Bifurcation Behavior and Imperfection Sensitivity of Elastic/Plastic Circular Plates, Int. J. Mech. Sci., 17, 1.
Onat, E.T. and Drucker, D.C. (1953), Inelastic Instability and Incremental Theories of Plasticity, J. Aeronaut. Sci., 20, 181.
Pearson, CE. (1950), Bifurcation Criteria and Plastic Buckling of Plates and Columns, J. Aeronaut. Sci., 17, 417.
Pearson, C.E. (1956), A General Theory of Elastic Stability, Quart. Appl. Math., 14, 133.
Petryk, H. (1983), A Stability Postulate for Quasi-Static Processes of Plastic Deformation, Arch. Mech., 35, 753.
Pugsley, A. (1979), On the Crumpling of Thin Cylindrical Tubes, Quart. J. Mech. Appl. Math., 32, 1.
Pugsley, A. and Macaulay, M. (1960), Large Scale Crumpling of Thin Cylindrical Columns, Quart. J. Mech. Appl. Math., 13, 1.
Reddy, B.D. (1979), Plastic Buckling of a cylindrical Shell in Pure Bending, Int. J. Mech. Sci., 21, 671.
Reddy, B.D. (1980), Buckling of Elastic-Plastic Discretely Stiffened Cylinders in Axial Compression, Int. J. Solids Struct., 16, 313.
Rees, D.W.A. (1982), Plastic Torsional Buckling of Thin-Walled Cylinders, J. Appl. Mech., 49, 663.
Seide, P. and Weingarten, V.I. (1961), On the Buckling of Circular Cylindrical Shells Under Pure Bending, J. Appl. Mech., 28, 112.
Sewell, M.J. (1963), A General Theory of Elastic and Inelastic Plate Failure, Part I, J. Mech. Phys. Solids, 11, 377.
Sewell, M.J. (1964), A General Theory of Elastic and Inelastic Plate Failure, Part II, J. Mech. Phys. Solids, 12, 279.
Sewell, M.J. (1973), A Yield Surface Corner Lowers the Buckling Stress of an Elastic/Plastic Plate, J. Mech. Phys. Solids, 21, 19.
Shanley, F.R. (1947), Inelastic Column Theory, J. Aeronaut. Sci., 14, 251.
Shrivastava, H.P. (1979), Inelastic Buckling of Axially Compressed Cylindrical Shells, Int. J. Solids Struct., 15, 567.
Southwell, R.V. (1913), On the Collapse of Tubes by External Pressure, Phil. Mag., 25, 687.
Timoshenko, S.P. and Gere, J.M. (1961), Theory of Elastic Stability, 2nd ed., McGraw-Hill, New York.
Tomita, Y. (1994), Simulations of Plastic Instabilities in Solid Mechanics, Appl. Mech. Rev., 47, 171.
Tugcu, P. (1991), Plate Buckling in the Plastic Range, Int. J. Mech. Sci., 33, 1.
von Karman, Th. (1910), Untersuchungen Ãœber Knickfestigkeit, Mitteilungen Ãœber Forschungsarbeit, Ver. Deut. Ing., Vol. 81, Springer-Verlag, Berlin.
Wierzbicki, T. and Abramowicz, W. (1983), On the Crushing Mechanism of Thin-Walled Structures, J. Appl. Mech., 50, 727.
Zhang, L.C. and Yu, T.X. (1987), An Investigation of the Brazier Effect of a Cylindrical Tube Under Pure Elastic-Plastic Bending, Int, J. Pres. Ves. Piping, 30, 77.
Author information
Authors and Affiliations
Rights and permissions
Copyright information
© 2000 Springer Science+Business Media New York
About this chapter
Cite this chapter
Chakrabarty, J. (2000). Plastic Buckling. In: Applied Plasticity. Mechanical Engineering Series. Springer, New York, NY. https://doi.org/10.1007/978-1-4757-3268-9_7
Download citation
DOI: https://doi.org/10.1007/978-1-4757-3268-9_7
Publisher Name: Springer, New York, NY
Print ISBN: 978-1-4757-3270-2
Online ISBN: 978-1-4757-3268-9
eBook Packages: Springer Book Archive