Abstract
In the previous chapter the imaging properties of amplitude and phase zone plates were considered, on the assumption that the zone boundaries were correctly positioned. These properties will be modified for realizable zone plates, since the boundaries cannot be positioned with arbitrary accuracy. In particular, the intensity in each of the predicted foci will, in general, be decreased, the point spread functions will be changed, and further foci may be obtained. A normally less important modification may be to the positions of the foci. In addition, amplitude zone plates for soft X rays are normally made on a supporting substrate, causing the open zones to be partially absorbing, while the closed zones may not be thick enough to be totally absorbing. By placing limits on the effects of these changes, for example by stipulating that diffraction-limited imaging is required, manufacturing tolerances can be obtained. The types of manufacturing error, and the corresponding tolerances, depend on the method of making the zone plates. Some methods for manufacturing amplitude zone plates will be discussed later in this chapter, while in this section tolerances will be established. The manufacture of phase zone plates will be discussed in Chapter 11, since the optical properties of most materials in the soft X-ray region are not yet known with sufficient accuracy to enable them to be designed and made with any confidence.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Preview
Unable to display preview. Download preview PDF.
Chapter 9
W. T. Welford, Aberrations of the Symmetrical Optical System, p. 206, Academic Press, New York (1974).
M. Born and E. Wolf, Principles of Optics, 5th ed., p. 468, Pergamon Press, Elmsford, N.Y. (1975).
M. J. Simpson, Design considerations of zone plate optics for a scanning transmission x-ray microscope, Ph.D. thesis, London University (1984).
M. J. Simpson and A. G. Michette, The effects of manufacturing inaccuracies on the imaging properties of Fresnel zone plates, Opt. Acta, 30, 1455–1462 (1983).
I. Brodie and J. J. Muray, The Physics of Microfabrication, Plenum Press, New York (1982).
D. C. Shaver, D. C. Flanders, N. M. Ceglio, and H. I. Smith, X-ray zone plates fabricated using electron-beam and x-ray lithography, J. Vac. Sci. Technol., 16, 1626–1630 (1979).
D. P. Kern, P. J. Houzego, P. J. Coane, and T. H. P. Chang, Practical aspects of microfabrication in the 100 nm region, J. Vac. Sci. Technol., B1, 1096–1100 (1983).
H. Aritome, H. Aoki, and S. Namba, Focusing characteristics of x-ray zone plates fabricated by electron beam lithography and reactive ion etching, Jpn. J. Appl. Phys. Part 2, 23, L406–L408 (1984).
E. Kratschmer, D. Stephani, and H. Beneking, High resolution 100 keV e-beam lithography, in: Microcircuit Engineering 83 (H. Ahmed, J. R. A. Cleaver, and G. A. C. Jones, eds.), pp. 15–22, Academic Press, New York (1983).
J. M. Warlaumont, Status of microstructure fabrication, High Resolution Soft X-Ray Optics, Proc. SPIE 316, 109–119 (1981).
C. D. Wilkinson, Fabrication of very small structures, in: Examining the Submicron World (R. Feder, J. Wm. McGowan, and D. M. Shinozaki, eds.), NATO ASI Series, Series B: Physics, Vol. 137, pp. 215–229, Plenum Press, New York (1986).
K. Murata, D. F. Kyser, and C. H. Ting, Monte Carlo simulation of fast secondary electron production in electron beam resists, J. Appl. Phys., 52, 4396–4405 (1981).
A. N. Broers, J. M. E. Harper, and W. W. Molzen, 250 Å linewidths with PMMA electron resist. Appl. Phys. Lett., 33, 392–394 (1978).
P. Charalambous, Image data collection, contamination and beam writing in the STEM, Ph.D. thesis, London University (1982).
L. Reiner and M. Wächter, Contribution to the contamination problem in transmission electron microscopy, Ultramicroscopy, 3, 169–174 (1978).
Y. Harada, T. Tomita, T. Watabe, H. Watanabe, and T. Etoh, Reduction of contamination in analytical electron microscopy, Scanning Electron Microscopy II (O. Johari and R. P. Becker, eds.), pp. 103–110, SEM Inc., AMF O’Hare (1979).
A. N. Broers, J. Cuomo, J. Harper, W. Molzen, R. Laibowitz, and M. Pomerants, High resolution electron beam fabrication using STEM, Ninth International Congress on Electron Microscopy, Toronto, Vol. 3, pp. 343–354 (1978).
M. T. Browne, P. Charalambous, and R. E. Bürge, Uses of contamination in STEM: Projection electron lithography, Inst. Phys. Conf. Ser. 61, 43–44 (1982).
A. G. Michette, M. T. Browne, P. Charalambous, R. E. Burge, M. J. Simpson, and P. J. Duke, Fabrication of small linewidth diffractive optics for use with soft x-rays, in: X-Ray Microscopy (G. Schmahl and D. Rudolph, eds.), Springer Series in Optical Sciences, Vol. 43, pp. 109–118, Springer, Berlin (1984).
A. G. Michette and R. E. Burge, Manufacture and tests of objective zone plates for use in a scanning transmission x-ray microscope, J. Microsc. (Oxford), 138, 303–309 (1985).
C. J. Buckley, M. T. Browne, and P. Charalambous, Contamination lithography for the fabrication of zone plate x-ray lenses, Electron-Beam, X-Ray and Ion-Beam Techniques for Submicrometer Lithography IV, Proc. SPIE 537, 213–217 (1985).
E. Spiller and R. Feder, X-ray lithography, in: X-Ray Optics (H.-J. Queisser, ed.), Topics in Applied Physics, Vol. 22, pp. 35–92, Springer, Berlin (1977).
G. Schmahl and D. Rudolph, High power zone plates as image forming systems for soft x-rays, Optik (Stuttgart), 29, 577–585 (1969).
J. H. Dijkstra, W. de Graaff:, and L. J. Lantwaard, Construction of apodized zone plates for solar x-ray image formation, in: New Techniques in Space Astronomy (F. Labuhn and R. Lust, eds.), pp. 207–210, Reidel, Dordrecht (1971).
D. Rudolph, Holographische Zonenplatten als abbildende Systeme für die Röntgenastronomie, Forschungsbericht W74-07 des Bundesministeriums für wis-senschaftliche Forschung (1974).
G. Schmahl, D. Rudolph, P. Guttmann and O. Christ, Zone plates for x-ray microscopy, in: X-Ray Microscopy (G. Schmahl and D. Rudolph, eds.), Springer Series in Optical Sciences, Vol. 43, pp. 63–74, Springer, Berlin (1984).
P. Guttmann, Construction of a micro zone plate and evaluation of imaging properties, in: X-Ray Microscopy (G. Schmahl and D. Rudolph, eds), Springer Series in Optical Sciences, Vol. 43, pp. 75–90, Springer, Berlin (1984).
J. Thieme, Construction of condenser zone plates for a scanning x-ray microscope, in: X-Ray Microscopy (G. Schmahl and D. Rudolph, eds.), Springer Series in Optical Sciences, Vol. 43, pp. 91–96, Springer, Berlin (1984).
K. H. von Grote, G. Mollenstedt and R. Spiedel, Preparation of short focal length zone plates for x- and uv-rays, and of correction plates for electron microscopes, Optik (Stuttgart), 22, 252–269 (1965).
B. E. Bol Raap, J. B. le Poole, J. H. Dijkstra, W. de Graaff, and L. J. Lantwaard, X-ray heliography by means of a Fresnel-Soret type zone plate camera, in: Small Rocket Instrumentation Techniques (Ken-Ichi Maeda, ed.), pp. 203–210, North- Holland, Amsterdam (1969).
H. W. P. Koops and J. Grob, Submicron lithography by demagnifying electron beam projection, in: X-Ray Microscopy (G. Schmahl and D. Rudolph, eds.), Springer Series in Optical Sciences, Vol. 43, pp. 119–128, Springer, Berlin (1984).
F. Kalk and D. Glocker, Thick zone plate fabrication using reactive sputter etching, J. Vac. Sci. Technol., 19, 170–172 (1981).
D. Glocker and R. Wiseman, A new method for the batch production of micro-Fresnel zone plates, J. Vac. Sci. Technol., 20, 1098–1100 (1982).
Y. Vladimirsky, E. Källne, and E. Spiller, Fabrication of free standing x-ray transmission gratings and zone plates, X-Ray Lithography and Applications of Soft X-Rays to Technology, Proc. SPIE 448, 25–37 (1984).
D. Rudolph and G Schmahl, High power zone plates for a soft x-ray microscope, in: Ultrasoft X-Ray Microscopy: Its Application to Biological and Physical Sciences (D. F. Parsons, ed.), Ann. N. Y. Acad. Sei. Vol. 342, pp. 94–104 (1980).
Y. S. Toulokian and C. X. Ho (eds.), Thermodynamic Properties of Matter, IFI/Plenum Data, New York (1970).
Author information
Authors and Affiliations
Rights and permissions
Copyright information
© 1986 Plenum Press, New York
About this chapter
Cite this chapter
Michette, A.G. (1986). Manufacture of Zone Plates. In: Optical Systems for Soft X Rays. Springer, Boston, MA. https://doi.org/10.1007/978-1-4613-2223-8_9
Download citation
DOI: https://doi.org/10.1007/978-1-4613-2223-8_9
Publisher Name: Springer, Boston, MA
Print ISBN: 978-1-4612-9304-0
Online ISBN: 978-1-4613-2223-8
eBook Packages: Springer Book Archive