Abstract
Modern lithium-ion cells are subject to a wide range of performance requirements, driven by the needs of their end users. Since lithium-ion cells are being used to power devices ranging from household electronics, through power tools to automobiles and the application types vary from commercial to military power sources, there is no universal user profile. The cells are usually classified either as “high energy” or “high power,” although the intermediate variants exist. For each distinct cell design option, appropriate selection of cell materials that are “best for the application” is made and, from this point, systematic process of optimization of materials’ performance in a cell begins. From the functional standpoint, lithium-ion electrode materials are divided into “active materials” that are capable of reversibly intercalating lithium ions into their structure, “conductive diluents” that assist in electron conduction within the electrode, current collecting foils, as well as binders that assure adhesion to current collectors and cohesion within the electrode. Electrolyte solutions and porous separators are other cell materials that must be properly selected to match the cell design.
This is a preview of subscription content, log in via an institution.
Buying options
Tax calculation will be finalised at checkout
Purchases are for personal use only
Learn about institutional subscriptionsNotes
- 1.
Originally, the term intercalation was reserved only for the layered materials’ host structures; nowadays this term can be seen applied to other types of structures as well (e.g., spinel-structured materials). The term also applies to ions other than Li+ (e.g., Mg2+).
References
Whittingham MS (2004) Lithium batteries and cathode materials. Chem Rev 104:4271–4301. doi:10.1021/cr020731c
Levasseur S, Menetrier M, Suard E, Delmas C (2000) Evidence for structural defects in non-stoichiometric HT-LiCoO2: electrochemical, electronic properties and Li-7 NMR studies. Solid State Ionics 128:11–24. doi:10.1016/S0167-2738(99)00335-5
Reimers JN, Dahn JR (1992) Electrochemical and insitu X-ray-diffraction studies of lithium intercalation in LixCoO2. J Electrochem Soc 139:2091–2097. doi:10.1149/1.2221184
Huggins RA (2009) Advanced batteries: materials science aspects. Springer, New York
Yamahira T, Kato H, Anzai M (1991) US Patent 5,053,297
Goodenough JB, Mizushima K (1981) US Patent 4,302,518, (1982) US Patent 4,357,215
Mizushima K, Jones PC, Wiseman PJ, Goodenough JB (1980) LixCoO2 (0 < x≤1): A new cathode material for batteries of high energy density. Mater Res Bull 15:783–789. doi:10.1016/0025-5408(80)90012-4
Lu CH, Yeh PY (2002) Microstructural development and electrochemical characteristics of lithium cobalt oxide powders prepared by the water-in-oil emulsion process. J Eur Ceram Soc 22:673–679. doi:10.1016/S0955-2219(01)00366-1
MacNeil DD, Dahn JR (2001) The reaction of charged cathodes with nonaqueous solvents and electrolytes - I. Li0.5CoO2. J Electrochem Soc 148:A1205–A1210. doi:10.1149/1.1407245
Nishi Y (2001) Lithium ion secondary batteries; past 10 years and the future. J Power Sources 100:101–106. doi:10.1016/S0378-7753(01)00887-4
Chen Z, Ellenwood R (2010) US Patent Application US20100176352
B. Scrosati (2000) Recent advances in lithium ion battery materials. Electrochim Acta 45:2461–2466. doi:10.1016/S0013-4686(00)00333-9
http://www.iucr.org/education/pamphlets. Accessed 1 March 2013
Pecharsky VK, Zavalij PY (2005) Fundamentals of powder diffraction and structural characterization of materials. Springer, New York
Cho J, Kim YJ, Kim JT, Park B (2001) Zero-strain intercalation cathode for rechargeable Li-ion cell. Angew Chem Int Ed 40:3367-3369. doi:10.1002/1521-3773(20010917)40:18<3367::AID-ANIE3367>3.0.CO;2-A
Wang ZX et al (2002) Electrochemical evaluation and structural characterization of commercial LiCoO2 surfaces modified with MgO for lithium-ion batteries. J Electrochem Soc 149:A466–A471. doi:10.1149/1.1456919
Kim Y, Kim D, Kang S (2011) Experimental and first-principles thermodynamic study of the formation and effects of vacancies in layered lithium nickel cobalt oxides. Chem Mater 23:5388–5397. doi:10.1021/cm202415x
Kim JM, Chung HT (2004) The first cycle characteristics of Li[Ni1/3Co1/3Mn1/3]O2 charged up to 4.7 V. Electrochim Acta 49:937–944. doi:10.1016/j.electacta.2003.10.005
Li DC et al (2004) Effect of synthesis method on the electrochemical performance of LiNi1/3Mn1/3Co1/3O2. J Power Sources 132:150–155. doi:10.1016/j.jpowsour.2004.01.016
Chen YH, Wang CW, Zhang X, Sastry AM (2010) Porous cathode optimization for lithium cells: Ionic and electronic conductivity, capacity, and selection of materials. J Power Sources 195:2851–2862. doi:10.1016/j.jpowsour.2009.11.044
Dahbi M, Saadoune I, Gustafsson T, Edström K (2011) Effect of manganese on the structural and thermal stability of Li0.3Ni0.7-yCo0.3-yMn2yO2 electrode materials (y = 0 and 0.05). Solid State Ionics 203:37–41. doi:10.1016/j.ssi.2011.09.022
Feng J et al (2012) Electrochemical property of LiMn2O4 in overdischarged conditions. Funct Mater Lett 5:1250028. doi:10.1142/S1793604712500282
Padhi AK, Nanjundaswamy KS, Goodenough JS (1997) Phospho-olivines as positive-electrode materials for rechargeable lithium batteries. J Electrochem Soc, 144:1188–1194. doi:10.1149/1.1837571
Reddy TB, Linden D, eds (2010) Linden’s handbook of batteries 4th edition. McGraw-Hill, New York
Li G, Yang Z, Yang W (2008) Effect of FePO4 coating on electrochemical and safety performance of LiCoO2 as cathode material for Li-ion batteries. J Power Sources 183:741–748. doi:10.1016/j.jpowsour.2008.05.047
Xu F et al (2012) Failure Investigation of LiFePO4 cells under overcharge conditions. J Electrochem Soc 159:A678–A687. doi:10.1149/2.024206jes
Yamada A, Chung SC, Hinokuma K (2001) Optimized LiFePO4 for lithium battery cathodes. J Electrochem Soc 148:A224–A229. doi:10.1149/1.1348257
Ravet N et al Abs. 127, The Electrochemical Society and the Electrochemical Society of Japan Meeting Abstracts, vol. 99–2, Honolulu, HI, 17–22 October 1999
Tarascon JM et al (2010) Hunting for better Li-based electrode materials via low temperature inorganic synthesis. Chem Mater 22:724–739. doi:10.1021/cm9030478
Croce F et al (2002) A novel concept for the synthesis of an improved LiFePO4 lithium battery cathode. Electrochem Solid-State Lett 5:A47–A50. doi:10.1149/1.1449302
Rho YH, Nazar LF, Perry L, Ryan D (2007) Surface chemistry of LiFePO4 studied by Mossbauer and X-ray photoelectron spectroscopy and its effect on electrochemical properties. J Electrochem Soc 154:A283–A289. doi:10.1149/1.2433539
Chung SY, Bloking JT, Chiang YM (2002) Electronically conductive phospho-olivines as lithium storage electrodes. Nat Mater 1:123–128. doi:10.1038/nmat732
Herle PS, Ellis B, Coombs N, Nazar LF (2004) Nano-network electronic conduction in iron and nickel olivine phosphates. Nat Mater 3:147–152. doi:10.1038/nmat1063
Beguin F, Frackowiak E, eds (2009) Carbons for Electrochemical Energy Storage and Conversion Systems 1st edition. CRC Press, Boca Raton
Ridgeway P et al (2008) Effect of vinylene carbonate on graphite anode cycling efficiency. Electrochem Soc Trans 13:1–7
Zaghib K et al, Low-cost graphite and olivine-based materials for Li-ion batteries. BATT Review Meeting. Washington, DC February 25–28 2008
Barsukov IV et al, eds (2006) New Carbon Based Materials for Electrochemical Energy Storage Systems. Springer NATO Science Series. Dordrecht, Netherlands
Hirota N, Itabashi T, Maki S (2011) US Patent Application, 20110159360
Yoo M, Frank CW, Mori S, Yamaguchi S (2004) Interaction of poly(vinylidene fluoride) with graphite particles. 2. Effect of solvent evaporation kinetics and chemical properties of PVDF on the surface morphology of a composite film and its relation to electrochemical performance. Chem Mater 16:1945–1953. doi:10.1021/cm0304593
Amin-Sanayei R, Heinze R, NASA Aerospace Battery Workshop Presentation. Huntsville, AL 2009
Zheng H et al (2012) Cooperation between active material, polymeric binder and conductive carbon additive in lithium ion battery cathode. J Phys Chem C 116:4875–4882. doi:10.1021/jp208428w
Zheng H et al (2010) Cathode performance as a function of inactive material and void fractions. J Electrochem Soc 157:A1060–A1066. doi:10.1149/1.3459878
Spahr ME et al (2011) Development of carbon conductive additives for advanced lithium ion batteries. J Power Sources 196:3404–3413. doi:10.1016/j.jpowsour.2010.07.002
Xu K (2004) Nonaqueous liquid electrolytes for lithium-based rechargeable batteries. Chem Rev 104:4303–4417. doi:10.1021/cr030203g
Material Safety Data Sheet (MSDS) for EMC (CAS Number 623-53-0, 99 %), Sigma-Aldrich
Zinigrad E et al Abs. 245, The 210th Electrochemical Society Meeting Abstracts, Cancun, Mexico, October 29-November 3 2006
Lex-Balducci A et al (2010) Lithium borates for lithium-ion battery electrolytes. Electrochem Soc Trans 25:13–17
Zinigrad E et al (2007) On the thermal behavior of Li bis(oxalato)borate LiBOB. Thermochim Acta 457:64–69. doi:10.1016/j.tca.2007.03.001
Smart MC et al (2002) Performance characteristics of lithium ion cells at low temperatures. IEEE Trans Aerosp Electron Syst Mag 17:16-20. doi:10.1109/MAES.2002.1145732
Zhang SS (2007) A review on the separators of liquid electrolyte Li-ion batteries. J Power Sources 164:351–364. doi:10.1016/j.jpowsour.2006.10.065
Test method developed under auspices of the Technical Association of the Pulp and Paper Industry
American Society for Testing and Materials (ASTM)
Jeong HS, Hong SC, Lee SY (2010) Effect of microporous structure on thermal shrinkage and electrochemical performance of Al2O3/poly(vinylidene fluoride-hexafluoropropylene) composite separators for lithium-ion batteries. J Membr Sci 364:177–182. doi:10.1016/j.memsci.2010.08.012
Johnson CS et al (2008) Synthesis, characterization and electrochemistry of lithium battery electrodes: xLi2MnO3∙(1-x)LiMn0.333Ni0.333Co0.333O2 (0 ≤ x≤0.7). Chem Mater 20:6095–6106. doi: 10.1021/cm801245r
Sony news release. http://www.sony.net/SonyInfo/News/Press/200502/05-006E/index.html. Accessed 29 April 2013
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2014 Springer-Verlag London
About this chapter
Cite this chapter
Gulbinska, M.K. (2014). Lithium-ion Cell Materials in Practice. In: Gulbinska, M. (eds) Lithium-ion Battery Materials and Engineering. Green Energy and Technology. Springer, London. https://doi.org/10.1007/978-1-4471-6548-4_1
Download citation
DOI: https://doi.org/10.1007/978-1-4471-6548-4_1
Published:
Publisher Name: Springer, London
Print ISBN: 978-1-4471-6547-7
Online ISBN: 978-1-4471-6548-4
eBook Packages: EnergyEnergy (R0)