Advertisement

Fabrication of Microscale Rotating Magnetic Machines

  • David P. Arnold
  • Mark G. Allen
Chapter
Part of the MEMS Reference Shelf book series (MEMSRS)

Abstract

In this chapter, microfabrication techniques are discussed to enable miniaturized magnetic machines for use with silicon microturbomachinery. These rotational machines could be used as either motors (for motoring or fluidic pumping) or as generators for electrical power generation. Challenges and methods for microfabricating microscale magnetic machines are described, and examples of previously implemented devices are discussed.

Keywords

Permanent Magnet Metal Layer Seed Layer Eddy Current Loss Wafer Bonding 
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

References

  1. 1.
    Ahn CH, Kim YJ, Allen MG (1993) A planar variable reluctance magnetic micromotor with fully integrated stator and wrapped coils. Proc. IEEE MEMS Conf., Ft. Lauderdale, FL, Feb. 2003, 1–6Google Scholar
  2. 2.
    Arnold DP, Zana I, Cros F, Allen MG (2004a) Vertically laminated magnetic cores by electroplating Ni-Fe into micromachined Si. IEEE Trans. Magn. 40(4):3060–3062CrossRefGoogle Scholar
  3. 3.
    Arnold DP, Cros F, Zana I, Veazie D, Allen MG (2004b) Electroplated metal microstructures embedded in fusion-bonded silicon: conductors and magnetic materials. J. Microelectromech. Syst. 13(5):791–798CrossRefGoogle Scholar
  4. 4.
    Arnold DP, Zana I, Allen MG (2005) Analysis and optimization of vertically oriented, through-wafer, laminated magnetic cores in silicon. J. Micromech. Microeng. 15(5): 971–977CrossRefGoogle Scholar
  5. 5.
    Arnold DP, Das S, Cros F, Zana I, Lang JH, Allen MG (2006a) Magnetic induction machines integrated into bulk-micromachined silicon. J. Microelectromech. Syst. 15(2):406–414CrossRefGoogle Scholar
  6. 6.
    Arnold DP, Das S, Park J-W, Zana I, Lang JH, Allen MG (2006b) Microfabricated high-speed axial-flux multiwatt permanent-magnet generators – Part II: design, fabrication, and testing. J. Microelectromech. Syst. 15(5):1351–1363CrossRefGoogle Scholar
  7. 7.
    Arnold DP, Herrault F, Zana I, Galle P, Park J-W, Das S, Lang JH, Allen MG (2006c) Design optimization of an 8-Watt, microscale, axial-flux, permanent-magnet generator. J. Micromech. Microeng. 16(9):S290–S296CrossRefGoogle Scholar
  8. 8.
    Bowers BJ, Agashe JS, Arnold DP (2007) A method to form bonded micromagnets embedded in silicon. Tech. Dig. 14th Int. Conf. Solid-State Sensors, Actuators, and Microsystems (Transducers ’07), Lyon, France, June 2007, vol.2, 1581–1584Google Scholar
  9. 9.
    Budde T, Gatzen HH (2006) Thin film SmCo magnets for use in electromagnetic microactuators. J. Appl. Phys. 99:08N304CrossRefGoogle Scholar
  10. 10.
    Busch-Vishniac IJ (1992) The case for magnetically-driven micro-actuators Sens. & Actuat. A33:207–220CrossRefGoogle Scholar
  11. 11.
    Campbell P (1994) Permanent magnet materials and their application. Cambridge University Press, Cambridge, UK, Ch. 2CrossRefGoogle Scholar
  12. 12.
    Cho H, Ahn C (2003) Microscale resin-bonded permanent magnets for magnetic micro-electro-mechanical systems applications. J. Appl. Phys. 93(10):8674–8676CrossRefGoogle Scholar
  13. 13.
    Cooper EI, Bonhôte C, Heidmann J, Hsu Y, Kern P, Lam JW, Ramasubramanian M, Robertson N, Romankiw LT, Xu H (2005) Recent developments in high-moment electroplated materials for recording heads. IBM J. Res. Develop. 49:103–126CrossRefGoogle Scholar
  14. 14.
    Cugat O, Delamare J, Reyne G (2003) Magnetic micro-actuators and systems (MAGMAS). IEEE Trans. Magn. 39:3607–3612CrossRefGoogle Scholar
  15. 15.
    Cullity BD, Graham CD (2009) Introduction to magnetic materials. IEEE Press/Wiley, Hoboken, New JerseyGoogle Scholar
  16. 16.
    Das S, Arnold DP, Zana I, Park J-W, Allen MG, Lang JH (2006) Microfabricated high-speed axial-flux multiwatt permanent-magnet generators – Part I: modeling. J. Microelectromech. Syst. 15(5):1330–1350CrossRefGoogle Scholar
  17. 17.
    Dempsey NM, Walther A, May F, Givord D, Khlopkov K, Gutfleisch O (2007) High performance hard magnetic NdFeB thick films for integration into micro-electro-mechanical systems. App. Phys. Lett. 90:092509CrossRefGoogle Scholar
  18. 18.
    Dutoit BM, Bese P-A, Blanchard H, Guérin L, Popovich RS (1999) High performance micromachined Sm2Co17 polymer bonded magnets. Sens. Actuat. 77:178–182CrossRefGoogle Scholar
  19. 19.
    Dyos GT, Farrell T, Eds. (1992) Electrical resistivity handbook. Peter Peregrinus Ltd., LondonGoogle Scholar
  20. 20.
    Ehrfeld W, Gotz F, Munchmeyer D, Schelb W, Schmidt D (1988) “LIGA process: Sensor construction techniques via x-ray lithography,” Proc. IEEE Solid State Sensor and Actuator Workshop, 1–4.Google Scholar
  21. 21.
    Frazier AB, Allen MG (1992) High aspect ratio electroplated microstructures using a photosensitive polyimide process, Proc. IEEE MEMS Conf., Travemuende, Germany, 87–92Google Scholar
  22. 22.
    Furlani EP (2001) Permanent magnet and electromechanical devices. Academic Press, San Diego, CA, Ch 1CrossRefGoogle Scholar
  23. 23.
    Ge J, Turunen MPK, Kivilahti JK (2003) Surface modification and characterization of photodefinable epoxy/copper systems. Thin Solid Films 440:198–207CrossRefGoogle Scholar
  24. 24.
    Gilles P-A, Delamare J, Cugat O (2002) Rotor for a brushless micromotor. J. Magnet Magn. Mat. 242–245:1186–1189CrossRefGoogle Scholar
  25. 25.
    Guan S, Nelson BJ (2005a) Pulse-reverse electrodeposited nanograinsized CoNiP thin films and microarrays for MEMS actuators. J. Electrochem. Soc. 152(4):C190–C195CrossRefGoogle Scholar
  26. 26.
    Guan S, Nelson BJ (2005b) Fabrication of hard magnetic microarrays by electroless codeposition for MEMS actuators. Sens. & Actuat. A 118:307–312CrossRefGoogle Scholar
  27. 27.
    Guan S, Nelson BJ (2006) Magnetic composite electroplating for depositing micromagnets. J. Microelectromech. Syst. 15(2):330–337CrossRefGoogle Scholar
  28. 28.
    Lagorce L, Allen MG (1997) Magnetic and mechanical properties of micromachined strontium ferrite/polyimide composites. J. Microelectromech. Syst. 6(4):307–312CrossRefGoogle Scholar
  29. 29.
    Lammeraner J, Stafl M (1966) Eddy current. Iliffe, London, ch.1–2.Google Scholar
  30. 30.
    Lorenz H, Despont M, Fahrni N, LaBianca N, Renaud P, Vettiger P (1997) SU-8: A low-cost negative resist for MEMS. J. Micromech. Microeng. 7:121–124CrossRefGoogle Scholar
  31. 31.
    Magnetic Materials Producers Association, MMPA Standard No. 0100-00, Standard Specifications for Permanent Magnet Materials. Available http://www.intl-magnetics.org
  32. 32.
    Nordström M, Johansson A, Noguerón ES, Clausen B, Calleja M, Boisen A (2005) Investigation of the bond strength between the photo-sensitive polymer SU-8 and gold. Microelec. Eng. 78–79:152–157Google Scholar
  33. 33.
    O’Handley RC (2000) Modern magnetic materials. Wiley, New YorkGoogle Scholar
  34. 34.
    Park JY, Han SH, Allen MG (1999) Batch-fabricated microinductors with electroplated magnetically anisotropic and laminated alloy cores. IEEE Trans. Magn. 35:4291–4300CrossRefGoogle Scholar
  35. 35.
    Park JW, Park JY, Joung YH, Allen MG (2002) Fabrication of high current and low profile micromachined inductor with laminated Ni/Fe core. IEEE Trans. Comp. Packag. Technol. 25:106–111CrossRefGoogle Scholar
  36. 36.
    Park JW, Allen MG (2003) Ultralow-profile micromachined power inductors with highly laminated Ni/Fe cores: Application to low-megahertz dc-dc converters. IEEE Trans. Magn. 39:3184–3186CrossRefGoogle Scholar
  37. 37.
    Pawlowski B, Töpfer J (2004) Permanent magnetic NdFeB thick films. J. Mat. Sci. 39:1321–1324CrossRefGoogle Scholar
  38. 38.
    Rhen FMF, Backen E, Coey JMD (2005) Thick-film permanent magnets by membrane electrodeposition. J. Appl. Phys. 97:113908CrossRefGoogle Scholar
  39. 39.
    Riley CD, Jewell GW, Howe D (1998) The design and analysis of axial field multipole impulse magnetizing fixtures. J. App. Phys. 83:7112–7114CrossRefGoogle Scholar
  40. 40.
    Romankiw LT, Croll I, Hatzakis M (1970) Batch-fabricated thin film magnetic recording heads. IEEE Trans. Magn. 6(3):597–601CrossRefGoogle Scholar
  41. 41.
    Romero JJ, Cuadrado R, Pina E, de Hoyos A, Pigazo F, Palomares FL, Hernando A, Sastre R, Gonzalez JM (2006) Anisotropic polymer bonded hard-magnetic films for microelectromechanical system applications. J. Appl. Phys. 99:08N303CrossRefGoogle Scholar
  42. 42.
    Schlesinger M, Paunovic M, Eds. (2000) Modern electroplating, 4th Ed. Wiley, New YorkGoogle Scholar
  43. 43.
    Schmidt MA (1988) Wafer-to-wafer bonding for microstructure formation. Proc. IEEE 86: 1575–1585CrossRefGoogle Scholar
  44. 44.
    Sullivan CR, Sanders SR (1995) Microfabrication process for high frequency power-conversion transformers. Proc. 26th Annu. Power Electronics Specialists Conf., June 1995, pp. 658–664Google Scholar
  45. 45.
    Thongmee S, Ding J, Lin JY, Blackwood DJ, Yi JB, Yin JH (2007) FePt films fabricated by electrodeposition. J. Appl. Phys. 101:09K519CrossRefGoogle Scholar
  46. 46.
    Tong Q-Y, Gösele U (1999) Semiconductor wafer bonding: science and technology. Wiley, New YorkGoogle Scholar
  47. 47.
    Töpfer J, Christoph V (2004) Multi-pole magnetization of NdFeB sintered magnets and thick films for magnetic micro-actuators. Sens. Actuat. A 113:257–263CrossRefGoogle Scholar
  48. 48.
    Trimmer W (1989) Microrobots and micromechanical systems. Sens. Actuat. 19:267–287CrossRefGoogle Scholar
  49. 49.
    Wagner, B, Kreutzer M, Benecke W (1992) Linear and rotational magnetic micromotorsfabricated using silicon technology. Proc. IEEE MEMS Conf., Travemuende, Germany, 183–189Google Scholar
  50. 50.
    Wang N, Arnold DP (2008) Thick electroplated Co-rich Co–Pt micromagnet arrays for magnetic MEMS. IEEE Trans. Magn. 44:3969–3972CrossRefGoogle Scholar
  51. 51.
    Wang N, Bowers BJ, Arnold DP (2008) Wax-bonded NdFeB micromagnets for microelectromechanical systems applications. J. Appl. Phys. 103:07E109CrossRefGoogle Scholar
  52. 52.
    Xu M, Liakopoulos TM, Ahn CH, Han SH, Kim HJ (1998) A microfabricated transformer for high-frequency power or signal conversion. IEEE Trans. Magn. 34:1369–1371CrossRefGoogle Scholar
  53. 53.
    Yufeng S, Wang H, Ding G, Cui F, Zhang W, Chen W (2005) Electroplated hard magnetic material and its application in microelectromechanical systems. IEEE Trans. Magn. 41(12):4380–4383CrossRefGoogle Scholar
  54. 54.
    Zana I, Herrault F, Arnold DP, Allen MG (2005) Magnetic patterning of permanent-magnet rotors for microscale motor/generators. Proc. 5th Int. Workshop Micro Nanotechnology For Power Generation and Energy Conversion Apps. (PowerMEMS 2005), Tokyo, Japan, Nov. 2005, 116–119Google Scholar

Copyright information

© Springer Science+Business Media, LLC 2009

Authors and Affiliations

  • David P. Arnold
    • 1
  • Mark G. Allen
    • 2
  1. 1.Department of Electrical and Computer EngineeringUniversity of FloridaGainesvilleUSA
  2. 2.School of Electrical and Computer EngineeringGeorgia Institute of TechnologyAtlantaUSA

Personalised recommendations