# Generation of Slip Line Fields Incorporating BUE and Shear Zone to Model Machining Using MATLAB

• Hridayjit Kalita
• Kaushik Kumar
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

## Abstract

Slip line field theory for modeling of machining process provides an analytical method where unknown slip lines are first generated assuming an initial base slip line and then are later evaluated considering different cutting and boundary conditions. All the slip lines are inter-dependent on each other and the curvature of these slip lines is altered with a slight change in the condition of cutting. This enables an inclusive and robust model to develop which can take into account the curling of the chip, frictional condition at the tool rake face and elastic condition at the upper end of the shear zone. In the current paper, an attempt to construct the slip lines using MATLAB has been presented based on the model given by Fang and Dewhurst and incorporating an additional shear zone into it. This model can detect buildup edge (BUE) of a larger size which influences directly the cutting forces and the curvature of the slip lines. The slip lines generated are studied and the characteristic of these can be observed by altering the input parameter values such as hydrostatic pressure at a fixed location, the rake angle of the tool or the input slip line angular ranges.

## Keywords

Slip line field Machining Modeling Shear zone Buildup edge Sticking region Curvature MATLAB

## References

1. 1.
Melkote SN, Grzesik W, Outeiro J, Rech J, Schulze V, Attia H, Arrazola PJ, M’Saoubi R, Saldana C (2017) Advances in material and friction data for modeling of metal machining. CIRP Annals Manuf Technol 66:731–754
2. 2.
Uhlmann E, Henze S, Bromelhoff K (2015) Influence of the built-up edge on the stress state in the chip formation zone during orthogonal cutting of AISI1045. Proc CIRP 31:310–315
3. 3.
Atlati S, Haddag B, Nouari M, Moufki A (2015) Effect of the local friction and contact nature on the built-up edge formation process in machining ductile metals. Tribol Int 90:217–227
4. 4.
Gomez-Parra A, lvarez-Alco MA, Salguero J, Batista M, Marcos M (2013) Analysis of the evolution of the built-up edge and built-up layer formation mechanisms in the dry turning of aeronautical aluminum alloys. Wear 302:1209–1218Google Scholar
5. 5.
Quagliato L, Berti GA (2017) Temperature estimation, and slip-line force analytical models for the estimation of the radial forming force in the RARR process of flat rings. Int J Mech Sci 123:311–323
6. 6.
Quagliato L, Berti GA, Kim D, Kim N (2018) Slip line model for forces estimation in the radial-axial ring rolling process. Int J Mech Sci 138–139:17–33
7. 7.
Freddi F, Carfagni GR (2016) Phase-field slip-line theory of plasticity. J Mech Phys Solids 94:257–272
8. 8.
Dewhurst P (1978) On the non-uniqueness of the machining process. Proc R Soc London Ser A 360:587–610Google Scholar
9. 9.
Lee EH, Shaffer BW (1951) The theory of plasticity applied to a problem of machining. Trans ASME 18:405–413Google Scholar
10. 10.
Fang N, Dewhurst P (2005) Slip-line modeling of built-up edge formation in machining. Int J Mech Sci 47:1079–1098
11. 11.
Fang N (2003) Slip-line modeling of machining with a rounded-edge tool—part I: new model and theory. J Mech Phys Solids 51:715–742
12. 12.
Jin X, Altintas Y (2011) Slip-line field model of micro-cutting process with round tool edge effect. J Mater Process Technol 211:339–355
13. 13.
Dewhurst P, Collins IF (1973) A matrix technique constructing slip-line field solutions to a class of plane strain plasticity problems. Int J Numer Meth Eng 7:357–378
14. 14.
Fang N, Jawahir IS, Oxley PLB (2001) A universal slip-line model with non-unique solutions for machining with curled chip formation and a restricted contact tool. Int J Mech Sci 43:557–580
15. 15.
Some built-up edge (BUE) is normally encountered in machining (2010) Engineering, Shop Floor. http://web.mit.edu/2.670/www/Tutorials/Machining/physics/bue.gif