Advertisement

Parametric Analysis on Surface Roughness of Micro-channel by Fiber Laser Milling on Zirconia (ZrO2)

  • O. F. BiswasEmail author
  • A. Sen
  • G. Kibria
  • Biswanath Doloi
  • B. Bhattacharyya
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

In the present days, the requirement of micro-machining has seen a rapid growth for the fabrication of precision machining of complex parts in automobile, shipbuilding, aerospace, electronics, medical industries, etc. Surface finish of these types of components is one of the most important criteria for fabricating better quality and to avoid failure caused by surface defects. The paper addresses the experimental investigation for the variation of surface roughness of micro-channel milling on flat zirconia (ZrO2) ceramics by using a pulsed fiber laser system. In this work, considered parameters are laser power, pulse frequency, laser scan speed, and the number of scan while responses considered are surface roughness parameters, i.e., Ra and Rz. The experimental results show that aforesaid factors revealed huge influences on surface finish criteria on machined micro-channel on zirconia ceramics.

Keywords

Fiber laser Micro-channel milling Zirconia Surface roughness 

References

  1. 1.
    Madfa, A.A., Al-Sanabani, F.A., Al-Qudami, N.H., Al-Sanabani, J.S., Amran, A.G.: Use of zirconia in dentistry: an overview. Open Biomater. J. 5, 1–9 (2014)CrossRefGoogle Scholar
  2. 2.
    Manicone, P.F., Iommetti, P.R., Raffaelli, L.: An overview of zirconia ceramics: basic properties and clinical applications. J. Dent. 35, 819–826 (2007)CrossRefGoogle Scholar
  3. 3.
    Rizvi, N.H., Apte, P.: Developments in laser micro-machining techniques. J. Mater. Process. Technol. 127(2), 206–210 (2002)CrossRefGoogle Scholar
  4. 4.
    Meijer, J.: Laser beam machining (LBM), state of the art and new opportunities. J. Mater. Process. Technol. 149(1–3), 2–17 (2004)CrossRefGoogle Scholar
  5. 5.
    Majumdar, J.D., Manna, I.: Laser processing of materials. Sadhana 28(3–4), 495–562 (2003)CrossRefGoogle Scholar
  6. 6.
    Mishra, S., Yadava, V.: Laser beam micro machining (LBMM)—a review. Opt. Lasers Eng. 73, 89–122 (2015)CrossRefGoogle Scholar
  7. 7.
    Campanelli, S.L., Casalino, G., Ludovico, A.D., Bonserio, C.: An artificial neural network approach for the control of the laser milling process. Int. J. Adv. Manuf. Technol. 66(9–12), 1777–1784 (2013)CrossRefGoogle Scholar
  8. 8.
    Leone, C., Genna, S., Tagliaferri, F., Palumbo, B., Dix, M.: Experimental investigation on laser milling of aluminium oxide using a 30 W Q-switched Yb:YAG fiber laser. Opt. Laser Technol. 76, 127–137 (2016)CrossRefGoogle Scholar
  9. 9.
    Kibria, G., Doloi, B., Bhattacharyya, B.: Experimental investigation and multi objective optimization of Nd:YAG laser micro-turning process of alumina ceramic using orthogonal array and grey relational analysis. Opt. Laser Technol. 48, 16–27 (2013)CrossRefGoogle Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2020

Authors and Affiliations

  1. 1.Department of Mechanical EngineeringBankura Unnayani Institute of EngineeringBankuraIndia
  2. 2.Department of Mechanical EngineeringCalcutta Institute of TechnologyHowrahIndia
  3. 3.Department of Mechanical EngineeringAliah UniversityKolkataIndia
  4. 4.Department of Production EngineeringJadavpur UniversityKolkataIndia

Personalised recommendations