Advertisement

Optimization of Tribological Properties of Al6061/9%Gr/WC Hybrid Metal Matrix Composites Using FGRA

  • Gangadhara Rao PonugotiEmail author
  • Pandu R. Vundavilli
  • Alluru Gopala Krishna
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

In the present work, Hybrid MMCs are developed using Al6061 as a matrix with graphite (Gr) and tungsten carbide (WC) as reinforcements. This investigation is motivated to estimate the tribological properties such as wear phenomenon and coefficient of friction. The composites produced through stir casting route, initially 3, 6, 9, and 12% of Gr are produced and the investigation of these composites for mechanical and microstructural properties indicates that 9% Gr shows better performance. So, hybrid composite of Al6061/9%Gr/WC (WC varies from 1, 2, 3%) produced. Thereafter in view of modeling and optimization of the tribological property of the composites, the wear tests are conducted on pin-on-disk tribometer under varying conditions of reinforcement percentage, load, sliding distance, and sliding velocity according to face-centered central composite design that consists of 30 experimental runs. The wear rate and coefficient of friction are recorded as the tribological property indicators. Regression models for each response in terms their control variables were developed and checked their adequacy with ANOVA. Consequently, these models were used for optimization. Fuzzy gray relational analysis (FGRA) was used to derive the values of optimal control variable. The suitability of this multi-response optimization approach which minimizes the wear rate and coefficient of friction simultaneously was analyzed and reported. Finally, the derived optimal tribological conditions of the composites were confirmed through the validation experimental results.

Keywords

Al6061/Gr/WC hybrid composites Mechanical properties Wear rate Coefficient of friction Multi-response optimization Fuzzy gray relational analysis (FGRA) 

References

  1. 1.
    Bodunrin MO, Alaneme KK, Chown LH (2015) Aluminum matrix hybrid composites: a review of reinforcement philosophies; mechanical, corrosion and tribological characteristics. J Mater Res Technol 4(4):434–445CrossRefGoogle Scholar
  2. 2.
    Shibata K, Ushio H (1994) Tribological application of MMC for reducing engine weight. Tribol Int 27(1):39–44CrossRefGoogle Scholar
  3. 3.
    Stojanovic B, Babic M, Mitrovic S, Vencl A, Miloradovic NM, Pantic M (2013) Tribological characteristics of aluminium hybrid composites reinforced with silicon carbide and graphite: a review. J Balkan Tribol Assoc 19(1):83–96Google Scholar
  4. 4.
    Reddy PS, Kesavan R, Vijaya Ramnath B (2018) Investigation of mechanical properties of aluminium 6061-silicon carbide. Boron Carbide Metal Matrix Compos, Silicon 10(2):495–502Google Scholar
  5. 5.
    Kaushik N, Singhaal S (2017) Mechanical and metallurgical examinations of stir cast aluminum matrix composites: a review study. Int J Eng Technol 9(4):3201–3217Google Scholar
  6. 6.
    Umashankar V, Anthony Xavior M, Karthikeyan S (2014) Experimental evaluation of the influence of processing parameters on the mechanical properties of SiC particle reinforced AA6061 aluminium alloy matrix composite by powder processing. J Alloy Compd 582(5):380–386CrossRefGoogle Scholar
  7. 7.
    Patel GCM, Krishna P, Vundavilli PR, Parappa Goudar MP (2016) Multi-objective optimization of squeeze casting process using genetic algorithm and particle swarm optimization. Arch Foundry Eng 16(3):172–186CrossRefGoogle Scholar
  8. 8.
    Beffort O, Long S, Cayron C, Kuebler J, Buffat PA (2007) Alloying effects on microstructure and mechanical properties of high volume fraction SiC-particle reinforced Al-MMCs made by squeeze casting infiltration. Compos Sci Technol 67(3):737–745CrossRefGoogle Scholar
  9. 9.
    Ghosh S, Sutradhar G, Sahoo P (2011) Wear performance of Al-5%SiC metal matrix composite using Taguchi method. J Tribol Res 11(4):33–40Google Scholar
  10. 10.
    Shouvik G, Prasanth S, Goutam S (2012) Wear behavior of Al–SiCp metal matrix composites and optimization using Taguchi method and grey relational analysis. J Miner Mater Charact Eng 11(11):1085–1094Google Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2019

Authors and Affiliations

  • Gangadhara Rao Ponugoti
    • 1
    Email author
  • Pandu R. Vundavilli
    • 2
  • Alluru Gopala Krishna
    • 3
  1. 1.Nalanda Institute of Engineering and TechnologySattenapalliIndia
  2. 2.School of Mechanical SciencesIndian Institute of Technology BhubaneswarBhubaneswarIndia
  3. 3.Department of Mechanical EngineeringJNTUKakinadaIndia

Personalised recommendations