Advertisement

Finite Element Modeling of Single Spark Material Removal and Heat Flux Distribution in Micro-Electro Discharge Machining Process

  • Ishwar Bhiradi
  • Leera Raju
  • Somashekhar S. HiremathEmail author
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

Micro-Electro Discharge Machining (Micro-EDM) is a prominent non-conventional machining process. In this process, material removal takes place due to the melting and evaporation of electrode materials. The process gained a lot of research interest due to its ample potential in machining metallic materials and simple construction. In this paper, a thermal model has been developed to study the single spark material removal in Micro-EDM process. Single spark material removal study provides the significant information about optimization of the input parameters such as pulsed DC voltage, input current, spark duration, material removal rate of the electrodes, and area of heat distribution on the workpiece. ANSYS multiphysics is used to study the thermal analysis to determine the temperature and heat flux distribution on the workpiece. Silver material is used for both the electrodes. To validate the model, experiments were designed and conducted on tailor-made Micro-EDM setup. From the simulation study, it was found that for the pulse-on time (spark duration) of 40 µs, the material removed for single per spark was 7.53 ng per spark and the maximum heat flux obtained was 2614.2 × 108 W/m2. Simulation results were compared with the actual machined results. Crater profile was analyzed by Veeco Wyko NT1100 non-contact surface profilometer. The material removed by the single spark is obtained up to 8.16 ng. There was 8% error variation between simulation and experimental study. This may be due to assumptions made during simulation study and the presence of elemental impurities.

Keywords

Micro-EDM ANSYS Single spark Material removal Surface profilometry 

References

  1. 1.
    Masuzawa T (2000) State of the art of micromachining. CIRP Ann Manuf Technol 49(2):473–488CrossRefGoogle Scholar
  2. 2.
    Alting L, Kimura F, Hansen HN, Bissacco G (2003) Micro engineering. CIRP Ann Manuf Technol 52(2):635–657CrossRefGoogle Scholar
  3. 3.
    Rajurkar KP, Levy G, Malshe A, Sundaram MM, McGeough J, Hu X, DeSilva A (2006) Micro and nano machining by electro-physical and chemical processes. CIRP Ann Manuf Technol 55(2):643–666CrossRefGoogle Scholar
  4. 4.
    Lee SH, Li XP (2001) Study of the effect of machining parameters on the machining characteristics in electrical discharge machining of tungsten carbide. J Mater Process Technol 115(3):344–358CrossRefGoogle Scholar
  5. 5.
    Raju L, Hiremath SS (2016) A State-of-the-art review on micro electro-discharge machining. Procedia Technol 25:1281–1288CrossRefGoogle Scholar
  6. 6.
    Venugopal TR, Rao R (2014) Development of micro-EDM incorporating in-situ measurement system. Procedia Mater Sci 5:1897–1905CrossRefGoogle Scholar
  7. 7.
    Li Y, Guo M, Zhou Z, Hu M (2002) Micro electro discharge machine with an inchworm type of micro feed mechanism. Precis Eng 26(1):7–14CrossRefGoogle Scholar
  8. 8.
    Jahan MP, Wong YS, Rahman M (2009) A study on the quality micro-hole machining of tungsten carbide by micro-EDM process using transistor and RC-type pulse generator. J Mater Process Technol 209(4):1706–1716CrossRefGoogle Scholar
  9. 9.
    Yu ZY, Rajurkar KP, Shen H (2002) High aspect ratio and complex shaped blind micro holes by micro EDM. CIRP Ann Manuf Technol 51(1):359–362CrossRefGoogle Scholar
  10. 10.
    Hiremath SS, Raju L (2017) Investigation on machining copper plates with NiP coated tools using tailor-made micro-electro discharge machine. Adv Mater Process Technol 3(4):522–538Google Scholar
  11. 11.
    Maradia U, Scuderi M, Knaak R, Boccadoro M, Beltrami I, Stirnimann J, Wegener K (2013) Super-finished surfaces using meso-micro EDM. Procedia CIRP 6:157–162CrossRefGoogle Scholar
  12. 12.
    Jeong YH, HanYoo B, Lee HU, Min BK, Cho DW, Lee SJ (2009) Deburring microfeatures using micro-EDM. J Mater Process Technol 209(14):5399–5406CrossRefGoogle Scholar
  13. 13.
    Sahu RK, Hiremath SS, Manivannan PV, Singaperumal M (2014) Generation and characterization of copper nanoparticles using micro-electrical discharge machining. Mater Manuf Process 29(4):477–486CrossRefGoogle Scholar
  14. 14.
    Sahu RK, Hiremath SS, Manivannan PV (2015) Ultrasonic technique for concentration characterization of copper nanofluids synthesized using μ-EDM: a novel experimental approach. Powder Technol 284:429–436CrossRefGoogle Scholar
  15. 15.
    Sahu RK, Hiremath SS (2017) Synthesis of aluminium nanoparticles in a water/polyethylene glycol mixed solvent using μ-EDM. In: IOP conference series: materials science and engineering, vol 225, No 1, p 012257. IOP PublishingGoogle Scholar
  16. 16.
    Katz Z, Tibbles CJ (2005) Analysis of micro-scale EDM process. The Int J Adv Manuf Technol 25(9–10):923–928CrossRefGoogle Scholar
  17. 17.
    Shankar P, Jain VK, Sundararajan T (1997) Analysis of spark profiles during EDM process. Mach Sci Technol 1(2):195–217CrossRefGoogle Scholar
  18. 18.
    Mandal D, Pal SK, Saha P (2007) Modeling of electrical discharge machining process using back propagation neural network and multi-objective optimization using non-dominating sorting genetic algorithm-II. J Mater Process Technol 186(1–3):154–162CrossRefGoogle Scholar
  19. 19.
    Yeo SH, Kurnia W, Tan PC (2007) Electro-thermal modelling of anode and cathode in micro-EDM. J Phys D Appl Phys 40(8):2513CrossRefGoogle Scholar
  20. 20.
    Mitra S, Vasa NJ, Singaperumal M (2010) Investigation on particle generation by micro-electro discharge machining. In: Micromachining and microfabrication process technology, XV, Vol 7590, p 75900 J. International Society for Optics and PhotonicsGoogle Scholar
  21. 21.
    Paul L, Korah LV (2016) Effect of power source in ECDM Process with FEM modeling. Procedia Technol 25:1175–1181CrossRefGoogle Scholar
  22. 22.
    Somashekhar KP, Panda S, Mathew J, Ramachandran N (2015) Numerical simulation of micro-EDM model with multi-spark. Int J Adv Manuf Technol 76(1–4):83–90CrossRefGoogle Scholar
  23. 23.
    Patel MR, Barrufet MA, Eubank PT, DiBitonto DD (1989) Theoretical models of the electrical discharge machining process. II. The anode erosion model. J Appl Phys 66(9):4104–4111CrossRefGoogle Scholar
  24. 24.
    DiBitonto, DD, Eubank PT, Patel MR, Barrufet MA (1989) Theoretical models of the electrical discharge machining process I. A simple cathode erosion model. J Appl Phys 66(9):4095–4103CrossRefGoogle Scholar
  25. 25.
    Kuriachen B, Varghese A, Somashekhar KP, Panda S, Mathew J (2015) Three-dimensional numerical simulation of microelectric discharge machining of Ti-6Al-4V. Int J Adv Manuf Technol 79(1–4):147–160CrossRefGoogle Scholar
  26. 26.
    Giridharan A, Samuel GL (2015) Modeling and analysis of crater formation during wire electrical discharge turning (WEDT) process. Int J Adv Manuf Technol 77(5–8):1229–1247CrossRefGoogle Scholar
  27. 27.
    Salonitis K, Stournaras A, Stavropoulos P, Chryssolouris G (2009) Thermal modeling of the material removal rate and surface roughness for die-sinking EDM. Int J Adv Manuf Technol 40(3–4):316–323CrossRefGoogle Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2019

Authors and Affiliations

  • Ishwar Bhiradi
    • 1
  • Leera Raju
    • 1
  • Somashekhar S. Hiremath
    • 1
    Email author
  1. 1.Indian Institute of Technology, MadrasChennaiIndia

Personalised recommendations