Preparation and Wear Behavior of Enamel Coating on Ti–6Al–4V ELI Titanium Alloy

  • Qiuyuan Feng
  • Yongqiang Zhang
  • Zhihong Dong
  • Pinghui Zhang
  • Jian Wang
  • Dingchun Wang
  • Qi Gao
  • Xiao Peng
  • Fuhui Wang
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

An enamel coating was prepared on the surface of Ti–6Al–4V extra low interstitial (ELI) titanium alloy by using slurry sintering process. The surface three-dimensional morphology, wear track morphology, microhardness and the tribological behavior of alloy with and without enamel coating and adhesion strength between the coating and base alloy were characterized by means of atomic force microscopy (AFM), scanning electron microscopy (SEM), microhardness test, friction and wear testing machine and thermal shock method, respectively. The morphologies of the coating and base alloy before and after wear were comparatively analyzed, and wear mechanism was discussed. The results show that the microstructure of enamel coating was compact and combines well with the base alloy. The thickness of enamel coating was about 30 μm, and the coating was uniform and smooth. Compared to base alloy, the hardness of enamel coating improved obviously. Under the condition of dry friction and wear, the wear mass loss and wear rate of alloy with enamel coating was little, only one quarter and about 29.6% of that for alloy without enamel coating. The alloy with enamel coating shows excellent wear-resistance. Wear mechanism of Ti–6Al–4V ELI titanium alloy is adhesive and abrasive wear, while the enamel coating shows abrasive wear.

Keywords

Titanium alloy Enamel coating Microhardness Friction and wear Wear mechanism 

Notes

Acknowledgements

The authors would like to acknowledge Prof. Zhiming Yu and Dr. Qiuping Wei from Zhongnan University for their assistance with experimental work.

References

  1. 1.
    G.B. Kenneth, Tribological properties of titanium alloys. Wear 151, 203–217 (1991)CrossRefGoogle Scholar
  2. 2.
    H.Y. Wu, P.Z. Zhang, J. Xu, Z. Xu, Current situations and applications of titanium alloys wear resistance coatings. Mater. Rev. 20, 74–77 (2006). (In Chinese)Google Scholar
  3. 3.
    Z.M. Tu, N. Li, Y.M. Zhu, Application and technology on Surface treatment of titanium and titanium alloys (National Defense Industry Press, Beijing, 2010). (In Chinese)Google Scholar
  4. 4.
    A. Zhecheva, W. Sha, S. Malinov, A. Long, Enhancing the microstructure and properties of titanium alloys through nitriding and other surface engineering methods. Surf. Coat. Technol. 200, 2192–2207 (2005)CrossRefGoogle Scholar
  5. 5.
    H. Mohseni, P. Nandwana, A. Tsoi, R. Banerjee, T.W. Schsrf, In situ nitrided titanium alloys: microstructural evolution during solidification and wear. Acta Mater. 83, 61–74 (2015)CrossRefGoogle Scholar
  6. 6.
    X.Y. Li, A.L. Fan, B. Tan, J.D. Pan, D.X. Liu, H. Huang, Z. Xu, Tribological behavior of molybdenum alloying layer on Ti6Al4V by double glow discharge technique. Tribology 23, 108–111 (2003). (In Chinese)Google Scholar
  7. 7.
    L. Qin, B. Tang, J.X. Zhao, Z. Xu, Friction and wear behavior of Ti-Mo diffusion layer on Ti6Al4V alloy substrate in sliding against GCr15. Chin. J. Nonferrous Met. 13, 570–573 (2006). (In Chinese)Google Scholar
  8. 8.
    S. Aliasghari, P. Skeldon, G.E. Thompson, Plasma electrolytic oxidation of titanium in phosphate/silicate electrolyte and tribological performance of the coatings. Appl. Surf. Sci. 316, 463–476 (2014)CrossRefGoogle Scholar
  9. 9.
    Y. Wang, H.J. Yu, C.Z. Chen, Z.H. Zhao, Review of the biocompatibility of micro-arc oxidation coated titanium alloy. Mater. Des. 85, 640–652 (2015)CrossRefGoogle Scholar
  10. 10.
    L.D. Zhao, E. Lugscheider, Reactive plasma spraying of Ti–6Al–4V alloy. Wear 253, 1214–1218 (2002)CrossRefGoogle Scholar
  11. 11.
    S.P. Zhao, S.K. Lv, W.J. Hao, Titanium alloy and its surface treatment (Haerbin University of Technology Press, Haerbin, 2003). (In Chinese)Google Scholar
  12. 12.
    S.X. Hui, Z. Zhang, J.S. Xiao, G.S. Yuan, Influence of Nb implantation on oxidation behavior of a high temperature titanium alloy at 650 °C. Acta Metall. Sin. 35, S127–S130 (1999)Google Scholar
  13. 13.
    W.L. Wu, X.W. Li, Research progress on laser cladding of titanium alloys. Rare Metal Mat. Eng. 35, 850–854 (2006). (In Chinese)Google Scholar
  14. 14.
    F. Weng, C.Z. Chen, H.J. Yu, Research status of laser cladding on titanium and its alloys: a review. Mater. Des. 58, 412–425 (2014)CrossRefGoogle Scholar
  15. 15.
    Z.L. Tang, F.H. Wang, W.T. Wu, Effect of Al2O3 and enamel coatings on 900 °C oxidation and hot corrosion behaviors of gamma-TiAl. Mater. Sci. Eng., A 276, 70–75 (2000)CrossRefGoogle Scholar
  16. 16.
    X.X. Rao, S.B. Hu, D.S. Qian, Preparation and property of enamel coating on titanium alloy. Electroplat. Finish. 29, 50–52 (2010). (In Chinese)Google Scholar
  17. 17.
    C.H. Guan, Z.L. Tang, F.H. Wang, W.T. Wu, S.Q. Li, Effect of enamel coating on oxidation and hot corrosion resistance of Ti–24Al–14Nb–3V. Chin. J. Mater. Res. 14, 75–80 (2000)Google Scholar
  18. 18.
    Y.M. Xiong, S.L. Zhu, F.H. Wang, Effect of ultrafine enamel coating on the oxidation and mechanical property of Ti60 alloy. Acta Metall. Sin. 40, 768–772 (2004)Google Scholar
  19. 19.
    C.H. Zhang, H.G. Yang, S. Zhang, X.C. Zhang, S.L. Zhu, F.H. Wang, Effect of cerium oxide on the microstructure and friction and wear behavior of enamel coating. Tribology 25, 198–202 (2005). (In Chinese)Google Scholar
  20. 20.
    W. Liu, W.Z. Li, J.B. Yang, H.Q. Liu, Current research status of enamel coatings on titanium alloys. Mater. Rev. 27, 45–48 (2013). (In Chinese)Google Scholar
  21. 21.
    J. Li, Y.Y. Wu, D.L. Wang, X.G. Hu, The microstructure and wear resistance characteristics of electroformed nickel and partially stabilized zirconia composite coatings. J. Mater. Sci. 35, 1751–1758 (2000)CrossRefGoogle Scholar
  22. 22.
    F.Y. Mi, S.L. Zhu, Long-term high temperature oxidation and hot corrosion behavior of an enamel coating on γ-TiAl intermetallics at 700 °C. Corros. Sci. Prot. Technol. 27, 254–258 (2015). (In Chinese)Google Scholar
  23. 23.
    J. Tao, Z.D. Huang, H.B. Liu, T. Wang, Y.Q. Wang, X.Z. Guo, Preparation and characterization of anti-oxidation enamel coating for Ti-based alloys at high temperature. J. Nanjing U. Aeronaut. Astronaut. 42, 505–509 (2010). (In Chinese)Google Scholar
  24. 24.
    V. Ocelík, D. Matthews, JThM De Hosson, Sliding wear resistance of metal matrix composite layers prepared by high power laser. Surf. Coat. Technol. 197, 303–315 (2005)CrossRefGoogle Scholar
  25. 25.
    Y.S. Mao, X.H. Cui, S.Q. Wang, D.S. Li, Z.R. Yang, Y. Sun, Wear and friction characteristics of Ti6Al4V alloy. J. Aeronaut. Mater. 33, 41–45 (2013). (In Chinese)Google Scholar
  26. 26.
    K.M. Chen, Q.Y. Zhang, X.X Li, L. Wang, S.Q. Wang, Dry sliding wear behavior of TC11 alloy/GCr15 steel tribo-pair, Rare Metal. Mat. Eng. 44, 1531–1535 (2000). (In Chinese)Google Scholar
  27. 27.
    K. Yang, J.W. Huang, X.M. Fan, D.S. Xiong, Preparation and properties of Al2O3/MoS2 composite coatings on Ti6Al4V alloy by cathodic plasma electrolytic deposition. Trans. Mater. Heat Treat. 37, 164–171 (2016). (In Chinese)Google Scholar
  28. 28.
    Y.Q Fu, N.L. Loh, A.W Batchelor, D.X. Liu, X.D. Zhu, J.W. He, K.W. Xu, Improvement in fretting wear and fatigue resistance of Ti–6Al–4V by application of several surface treatments and coatings. Surf. Coat. Technol. 106, 193–197 (1998)CrossRefGoogle Scholar
  29. 29.
    Y.Q. Fu, H.J. Du, Effects of the counterface materials on the tribological characteristics of CNX coating deposited on plasma-nitrided Ti–6Al–4V. Mater. Sci. Eng., A 298, 16–25 (2001)CrossRefGoogle Scholar

Copyright information

© Springer Nature Singapore Pte Ltd. 2018

Authors and Affiliations

  • Qiuyuan Feng
    • 1
  • Yongqiang Zhang
    • 1
  • Zhihong Dong
    • 2
  • Pinghui Zhang
    • 1
  • Jian Wang
    • 1
  • Dingchun Wang
    • 1
  • Qi Gao
    • 1
  • Xiao Peng
    • 2
  • Fuhui Wang
    • 3
  1. 1.Institute of Baoti, Baoti Group Ltd.ShannxiChina
  2. 2.Laboratory for Corrosion and ProtectionInstitute of Metal Research, Chinese Academy of SciencesLiaoningChina
  3. 3.School of Materials Science and EngineeringNortheastern UniversityLiaoningChina

Personalised recommendations