Advertisement

Characterization of Fatigue Behavior of Composite Sandwich Structures at Sub-Zero Temperatures

  • Samirkumar M. SoniEmail author
  • Ronald F. Gibson
  • Emmanuel O. Ayorinde

Abstract

This chapter summarizes recent studies of the flexural fatigue characteristics of foam core carbon/epoxy and glass/epoxy composite sandwich beams over the temperature range from 22°C to −60°C. Core shear was found to be the dominant fatigue failure mode for the test specimens over this temperature range. Significant increases in the useful fatigue life with brittle type core shear failure were observed at low temperatures by comparison with the corresponding room temperature behavior. Fatigue failure at the subzero temperatures was catastrophic and without any significant early warning, but the corresponding failures at room temperature were preceded by relatively slow but steadily increasing losses of stiffness. Two different approaches were used to investigate stiffness reductions during fatigue tests, and both approaches led to the same conclusions. Static finite element analyses confirmed the experimentally observed locations of fatigue crack initiation.

Keywords

Fatigue Life Load Level Face Sheet Sandwich Beam Subzero Temperature 
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

Notes

Acknowledgment

This work was performed while all of the authors were located at Wayne State University. The authors gratefully acknowledge the financial support of the United States. Office of Naval Research, and the guidance of ONR Program Officers Dr. Kelly Cooper and Dr. Yapa Rajapakse.

References

  1. 1.
    Zenkert D (1995) Introduction to sandwich construction. Chameleon, LondonGoogle Scholar
  2. 2.
    Vinson JR (1999) The behavior of sandwich structures of isotropic and composite materials. Technomic, Lancaster, PA.Google Scholar
  3. 3.
    Sharma N, Gibson RF, Ayorinde EO (2006) Fatigue of foam and honeycomb core composite sandwich structures:a tutorial. J. Sandw. Struct. Mater. 8(4):263–319CrossRefGoogle Scholar
  4. 4.
    Daniel IM, Gdoutos EE, Wang KA, Abbot JL (2002) Failure modes of composite sandwich beams. Int. J. Damage Mech. 11:309–334.CrossRefGoogle Scholar
  5. 5.
    Steeves CA, Fleck NA (2004) Collapse mechanisms of sandwich beams with composite faces and a foam core, loaded in three-point bending. Part I:analytical models and minimum weight design. Int. J. Mech. Sci. 46:561–583.CrossRefGoogle Scholar
  6. 6.
    Steeves CA, Fleck NA (2004) Collapse mechanisms of sandwich beams with composite faces and a foam core, loaded in three-point bending. Part II:experimental investigation and numerical modeling. Int. J. Mech. Sci.46:585–608.CrossRefGoogle Scholar
  7. 7.
    Harte AM, Fleck NA, Ashby MF (2001) The fatigue strength of sandwich beams with an aluminum alloy foam core. Int. J. Fatigue 23:499–507.CrossRefGoogle Scholar
  8. 8.
    Burman M, Zenkert D (1997) Fatigue of foam core sandwich beams —1:undamaged specimens. Int. J. Fatigue 19(7):551–561.CrossRefGoogle Scholar
  9. 9.
    Burman M, Zenkert D (1997) Fatigue of foam core sandwich beams —2:effect of initial damage. Int. J. Fatigue 19(8):563–578.CrossRefGoogle Scholar
  10. 10.
    Kanny K, Mahfuz H (2005) Flexural fatigue characteristics of sandwich structures at different loading frequencies. Compos. Struct. 67:403–410.CrossRefGoogle Scholar
  11. 11.
    Sharma SC, Murthy HN, Krishna M (2004) Interfacial studies in fatigue behavior of polyurethane sandwich structures. J. Reinf. Plast. Compos. 23(8):893–903.CrossRefGoogle Scholar
  12. 12.
    Kanny K, Mahfuz H, Thomas T, Jeelani S (2004) Temperature effects on the fatigue behavior of foam core sandwich structures. Polym. Polym. Compos. 12(7):551–559.Google Scholar
  13. 13.
    Soni S (2006) Characterization of fatigue damage in composite sandwich hull materials at low temperatures. M.Sc. Thesis, Wayne State University, Department of Mechanical Engineering, Detroit, MI.Google Scholar
  14. 14.
    Annual Book of ASTM Standards (2000). C 393—00:Standard Method of Flexure Test of Flat Sandwich Constructions, 15(03):23–24. American Society for Testing and Materials, Philadelphia, PA.Google Scholar
  15. 15.
    Baba BO, Gibson RF, Soni S (2006) The influence of fatigue cracks on the modal vibration response of composite sandwich beams. Proc. 21st Annu. Tech. Conf. American Soc. Compos. Dearborn, Michigan, paper No. 101.Google Scholar

Copyright information

© Springer Science+Business Media B.V. 2009

Authors and Affiliations

  • Samirkumar M. Soni
    • 1
    Email author
  • Ronald F. Gibson
    • 2
  • Emmanuel O. Ayorinde
    • 1
  1. 1.Mechanical Engineering Department, Advanced Composites Research LaboratoryWayne State UniversityDetroit
  2. 2.Mechanical Engineering DepartmentUniversity of Nevada-RenoRenoUSA

Personalised recommendations