Advertisement

Study of Combustion Stroke of Double-Chamber Explosive Gas Forming Device

  • A. Yu. Botashev
  • A. A. Musaev
  • R. A. Bayramukov
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

The double-chamber explosive gas forming device is a kind of pulse punching unit. The device comprises a combustion chamber and an operating cylinder separated from each other by a piston, at the top of which an elastic disc is mounted. The stamping process is carried out by the pressure of the elastic disc due to the kinetic energy of the piston being accumulated during the explosion stroke. The piston is accelerated by the pressure of a high-temperature gas formed in the combustion chamber through the gaseous fuel mixtures burnout. The explosion stroke process was analysed on the basis of the equations of rigid body dynamics and thermodynamics. As a result, the regularity of the piston motion was determined, and the optimal ratios of the geometric parameters of the stamping device were found, ensuring an increase in its effective energy. It is established that the motion pattern of a piston depends essentially on the ratios of the flow bore section of an exhaust valve and the cross section of an operating cylinder. If this ratio is less than 0.07, the piston oscillates along the length of the cylinder, which is not acceptable for the stamping process. If it is greater than 0.1, the piston moves monotonously, continuously accumulating kinetic energy, which ensures the punching process. It is also established that the optimum ratio of the operating cylinder and the combustion chamber is within the range of 1.3–2.5.

Keywords

Sheets stamping Gas-forming device Elastic medium Combustion stroke 

References

  1. 1.
    Il’in LN, Semenov EI (2009) Technology of sheet punching. Drofa, Moscow, p 479Google Scholar
  2. 2.
    Chudin VN, Yakovlev SS, Sobolev YaA (2004) Isothermal deformation of high-strength anisotropic metals. Mashinostroenie-1, Publishing House of TulGU, Moscow, 427 pGoogle Scholar
  3. 3.
    Kovalevich MV (2006) Calculation of modes of pneumothermal molding of box-shaped parts in superplasticity mode. Blank Prod Mech Eng 9:35–39Google Scholar
  4. 4.
    Larin SN (2010) Pneumoforming of cellular panels from anisotropic material. Izvestiya TulGU. Tech Sci 3:51–61Google Scholar
  5. 5.
    Alekseev PA, Panchenko EV (2010) Simulation of the process of shaping an axisymmetric shell in the regime of superplasticity. Izvestiya TulGU. Tech Sci 3:181–185Google Scholar
  6. 6.
    Bychkov SA, Borisevich VK, Krivtsov VS, Bragin AP (2007) On the concept of the use of technological criteria for the selection of pulsed technologies of sheet punching. Aviat Space Technol Technol 11:222–231Google Scholar
  7. 7.
    Borisevich VK, Naryzhny AG, Molodykh SI (2007) Influence of the transmitting medium on the deformation and precision of the part during pulsed stamping. Aviat Space Technol Technol 11(47):173–181Google Scholar
  8. 8.
    Taranenko ME (2014) Possibilities of punching autocausal panels from modern materials of increased strength on EG presses. Forging-stamping production. Process Mater Press 9:34–40Google Scholar
  9. 9.
    Botashev AYu, Bisilov NU (2013) Investigation of gas sheet punching with bilateral heating of billets. Blank Prod Eng 3:25–28Google Scholar
  10. 10.
    Kukhar VD, Legeyda VYu, Kireeva AE (2010) Formation of a shell from a conical blank by uniform pressure of a gaseous medium. Forging Forging Prod Mater Press 9:43–45Google Scholar
  11. 11.
    Malsugenov RS (2014) Development of a device for gas stamping of spiral heat exchanger panels. In: Current state of natural and engineering sciences: materials of the XVI international scientific and practical conference. Publishing house “Sputnik +”, Moscow, pp 36–41Google Scholar
  12. 12.
    Malsugenov RS (2015) Development, creation and testing of a device for gas stamping with back pressure. In: Development of technical sciences in the modern world, proceedings of the international scientific and practical conference, VoronezhGoogle Scholar
  13. 13.
    Sukhov VV (2007) Experience in creating gas-explosion systems with multipoint initiation of detonation of a methane-oxygen mixture. Aviat Space Technol Technol 1:182–185Google Scholar
  14. 14.
    Botashev AYu, Musaev AA (2012) Development, research and creation of a two-chamber device for gas sheet punching. Blank Prod Mech Eng 3:20–23Google Scholar
  15. 15.
    Musaev AA (2012) Development of initial data for development of a pilot-industrial sample of a two-chamber device for gas sheet stamping. Izvestiya Vysshikh Uchebnykh Zavedenii. Eng 3:43–48Google Scholar
  16. 16.
    Botashev AYu, Musaev AA, Betrakhmanov MA (2017) Impulse machine for processing materials by pressure. Patent RU 173177, IPC B21J 7/24, B21D 26/08., Bul. 23Google Scholar
  17. 17.
    Dyachenko VG (2009) The theory of internal combustion engines: textbook. Translation from the Ukrainian language. Hnadu, Kharkov, 500 pGoogle Scholar
  18. 18.
    Kovylov YuL (2013) Theory of work processes and modeling of ICE processes: textbook. Samara: Samara Publishing House. state. aerospace. University, 416 pGoogle Scholar
  19. 19.
    Erofeev VL, Semenov PD, Pryakhin AS (2008) Heat engineering: textbook for high schools. ICC “Academic Book”, Moscow, 488 pGoogle Scholar
  20. 20.
    Gdalev AV, Kozlov AV, Saprunov YuI, Mayorov SG (2012) Heat engineering: textbook. The Scientific Book, Saratov, p 286Google Scholar
  21. 21.
    Zausaev AF (2010) Difference methods for solving ordinary differential equations. In: Proc. Help. Samara State University. Techn. un., Samara, 100 pGoogle Scholar

Copyright information

© Springer Nature Switzerland AG 2019

Authors and Affiliations

  • A. Yu. Botashev
    • 1
  • A. A. Musaev
    • 2
  • R. A. Bayramukov
    • 1
  1. 1.Northern Caucasian State Humanitarian-Technological AcademyCherkesskRussia
  2. 2.Russian Academy of SciencesGroznyRussia

Personalised recommendations