Advertisement

Determination of Functional Relation Between Parameters of Weld Penetration Shape and Measurable Output Variables in Electron-Beam Welding Process

  • V. N. Lastovirya
  • A. A. Cherepakhin
  • R. V. Rodyakina
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

Parameters of weld penetration shape (depth and width) are subject to a nonstationary change during the process of electron-beam welding because of the effect of uncontrolled disturbances. This is unacceptable, especially for welding products of critical use. The lack of information about weld penetration shape during the process of welding dictates the need for periodic welding of reference specimens for its control, which reduces the efficiency of the EBW-technology. In this paper, an experimental approach is considered that makes it possible to determine a functional dependence between the parameters of a weld penetration shape and measurable output variables in the electron-beam welding process based on the energy balance of the beam in a vapor-gas crater. The presence of such an equation of connection makes it possible to carry out the current control over the formation of a weld penetration shape of the welded joint. The introduction of control or management of the current shape of weld penetration ensures the reliability of requirements’ realization of this technology.

Keywords

Experimental approach Energy balance of the beam Mapping of parameters’ spaces Parameters of weld penetration shape Planning of experiment 

References

  1. 1.
    Lastovirya VN (1997) The electron beam welding process as an object of controlling the shape of penetration. Weld Int 11(11):890–893.  https://doi.org/10.1080/09507119709447340CrossRefGoogle Scholar
  2. 2.
    Gladkov EA, Shiganov IN, Lastovirya VN (2017) Control of welding processes with using concentrated energy flows. Textbook for higher education school. Publishing House of Moscow State Technical University named after N.E. Bauman, Moscow, 111pGoogle Scholar
  3. 3.
    Lastovirya VN, Novokreshchenov VV, Rodyakina RV (2015) Formation of the substructure and crystallography of welded joints in tungsten single crystals. Weld Prod 3:10–25Google Scholar
  4. 4.
    Mladenov GM, Trushnikov DN, Belenky VYa, Koleva EG (2014) Electron-beam welding: monograph. Publishing House of Perm National Research Polytechnical University, Perm, p 374Google Scholar
  5. 5.
    Lastovirya VN (2008) Principles of controlling the shape of melting in the technological process of electron-beam welding. Mech Eng Eng Educ 3:12–21Google Scholar
  6. 6.
    Lastovirya VN (2007) Identification of the connection of the form of melting with energy balance of the beam in the process of electron-beam welding. Mech Eng Eng Educ 3:17–22Google Scholar
  7. 7.
    Lastovirya VN (1997) Process of electron-beam welding as the object of control of weld penetration shape. Weld Prod 5:2–5Google Scholar
  8. 8.
    Adler YP, Markova EV, Granovsky YuV (1976) Planning of an experiment in the search of optimal conditions. Science, Moscow, p 279Google Scholar
  9. 9.
    Lastovirya VN, Bessonova YuB (1998) Calculation of heat flow, radiated from the vapor-gas channel in the case of deep penetration electron beam welding. Phys Chem Mater Process 6:86–91Google Scholar
  10. 10.
    Lastovira VN, Novokreshchenov VV, Rodyakina RV (2017) Estimation of the current state of the form of melting based on energy balance of the beam in a steam-gas crater. Weld Prod 11:17–23Google Scholar
  11. 11.
    Novokreshchenov VV, Rodyakina RV, Lastovirya VN (2017) The effect of high-temperature annealing on the stability of the structure and properties of welded joints in tungsten single crystals with planar and axial geometry. Weld Int 31(8):641–646.  https://doi.org/10.1080/09507116.2017.1307521CrossRefGoogle Scholar
  12. 12.
    Lastovirya VN, Novokreshchenov VV, Rodyakina RV (2016) Formation of the substructure and crystallography of welded joints in tungsten single crystals. Weld Int 30(3):224–228.  https://doi.org/10.1080/09507116.2015.1044271CrossRefGoogle Scholar
  13. 13.
    Lastovirya VN, Novokreshchenov VV, Rodyakina RV (2015) Restoration of the geometry and properties of rollers of the lower section of bearings by surfacing. Weld Int 29(10):815–818.  https://doi.org/10.1080/09507116.2014.986890CrossRefGoogle Scholar
  14. 14.
    Lastovirya VN (2015) To the question of controlling the shape of melting in the process of electron-beam welding as a system of “energy source—steam and gas crater”. News Tula State Univ 6–2:263–271Google Scholar
  15. 15.
    Balashov VN, Dragunov VK, Goncharov AL, Terentyev EV (2016) Modeling of welding electron guns: a tutorial. Veche, Moscow, p 128Google Scholar
  16. 16.
    Vinogradov VA, Lastovirya VN (1986) On the relationship between parameters of the channel, formed during electron-beam welding, with the conditions of welding process. Phys Chem Mater Process Phys Chem Mater Process 6:98–102Google Scholar
  17. 17.
    Shcherbakov AV, Rodyakina RV, Kozhechenko AS, Gaponova DA, Goncharov AL, Dragunov VK (2017) An experimental study of current-density distributions of a technological electron beam. Tech Phys Lett 43(11):958–960CrossRefGoogle Scholar
  18. 18.
    Lastovirya VN, Novokreshchenov VV, Rodyakina RV (2017) Method of control the parameters of a normal distribution of energy source, realized on the basis of serial power unit for electron-beam welding. Weld Prod 12:15–18Google Scholar
  19. 19.
    Shcherbakov AV, Rodyakina RV, Gaponova DA, Dragunov VK (2017) Ionization of gases in welding electron guns. Weld Prod 11:24–30Google Scholar
  20. 20.
    Shcherbakov AV, Novokreshchenov VV, Rodyakina RV, Lastovirya VN (2016) Equipment of electron-beam complexes for the production of modern energy products: a manual. Veche, Moscow, p 208Google Scholar

Copyright information

© Springer Nature Switzerland AG 2019

Authors and Affiliations

  • V. N. Lastovirya
    • 1
  • A. A. Cherepakhin
    • 1
  • R. V. Rodyakina
    • 2
  1. 1.Moscow Polytechnical UniversityMoscowRussia
  2. 2.National Research University “MPEI”MoscowRussia

Personalised recommendations