Advertisement

Rolling of Refractory Metals on Four-Roll Passes Rolling Mills

  • L. A. Barkov
  • M. N. Samodurova
  • D. P. Galkina
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

Drop and rotary forgings of molybdenum or tungsten rods and wire rods requires a great number of operations accompanied by significant losses in expensive metals and low quality of half-finished products. Therefore, it is of great importance to develop new effective methods as well as the appropriate equipment for high-quality treatment of molybdenum, tungsten, and their alloys. The paper presents one of the methods—multi-pass rolling with multi-sided reduction of powder sintered blocks. Intensive three- or four-sided reduction of the block leads to a favorable strain-deformation conditions at the point of the applied deformation allowing to obtain the appropriate scheme of that state of the material. As a result, the plasticity of the rolled material increases and its cross-flowing slows down. High plasticity of the material allows to increase the degree of multi-sided reduction of rods or stocks and, therefore, to reduce the total number of treatment operations, to reduce the losses of metals, and to improve the quality of rolled products and their mechanical characteristics. Slowing down the cross-flowing of the metal during multi-sided reduction of its blocks in the process of rolling allows for a more effective deformation, low energy consumption, and cut number of block passes. Thus, four-sided reduction gives the most favorable scheme of the strain-deformation state of the material under the condition of multi-sided, nonuniform reduction of the blocks in the process of rolling.

Keywords

Molybdenum Tungsten Multi-pass rolling Four-sided reduction 

Notes

Acknowledgements

The work was supported by the Ministry of Education and Science of the Russian Federation (project No. 9.1329.2017/4.6).

References

  1. 1.
    Barkov LA, Kamenshchikov YuI, Mymrin SA et al (1992) Densification of PM sintered billets during rolling with four-side reduction. Izvestia Akademii nauk SSSR Metally 4:77–79Google Scholar
  2. 2.
    Barkov LA (1982) New methods for rolling P/M sections with four-sided reduction. Sov Powder Metall Metal Ceram 21(12):924–926Google Scholar
  3. 3.
    Vydrin VN, Barkov LA, Pastukhov VV et al (1978) Rolling of tungsten rods. Sov Powder Metall Metal Ceram 17(5):356–358CrossRefGoogle Scholar
  4. 4.
    Vydrin VN (1973) Economical rolling of shapes in four roll mills. Neue Huette 18(10):584–588 (in German)Google Scholar
  5. 5.
    Vydrin VN, Barkov LA, Goryachev EA (1975) Power engineering conditions for rolling titanium alloys in cross-shaped four-roller grooves. Tsvetnye Metally 9:60–62 (in Russian)Google Scholar
  6. 6.
    Samodurova MN, Barkov LA, Ivanov VA (2014) Metallurgy and technology of powdered molybdenum. Publishing Center of SUSU, ChelyabinskGoogle Scholar
  7. 7.
    Vydrin VN, Barkov LA, Pastukhov VV et al (1977) Roll mill stand. US Patent 4,198,841, 22 Apr 1980Google Scholar
  8. 8.
    Vydrin VN, Pastukhov VV, Barkov LA et al (1978) Mill Stand. US Patent 4,244,204, 13 Jan 1981Google Scholar

Copyright information

© Springer Nature Switzerland AG 2019

Authors and Affiliations

  • L. A. Barkov
    • 1
  • M. N. Samodurova
    • 1
  • D. P. Galkina
    • 2
  1. 1.South Ural State UniversityChelyabinskRussia
  2. 2.Zlatoust Branch of South, Ural State UniversityZlatoustRussia

Personalised recommendations