Advertisement

Profile Gear Grinding Temperature Determination

  • N. V. Lishchenko
  • V. P. Larshin
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

The paper is devoted to solving an important scientific and technical problem of determining the profile gear grinding temperature based on the choice of simple but at the same time adequate solution from the available analytical ones. The initial prerequisite for the paper developing concept is that of a moving heat source, which was originally proposed and investigated by J. C. Jaeger. In engineering applications, the moving heat source is often represented in the form of the moving contact zone between the grinding wheel and the workpiece surface, which forms a three-dimensional or two-dimensional temperature field in the Cartesian coordinate system around itself with and without taking into account the influence of the source length in the direction, which is perpendicular to the direction of the source moving, respectively. There is another possibility to simplify the determination of grinding temperature by choosing a one-dimensional solution of the differential heat conduction equation in which the source moving with the certain velocity is absent and replaced by the time of action of a stationary heat source. This time is equal to the ratio of the contact length to the velocity of its moving. Due to the high speeds of discontinuous gear grinding process, the replacement of the moving source by a stationary one often does not affect the accuracy of determining the grinding temperature in a thin surface layer.

Keywords

Gear grinding Grinding temperature Heat source 

References

  1. 1.
    Jin T, Yi J, Peng S (2017) Determination of burn thresholds of precision gears in form grinding based on complex thermal modelling and Barkhausen noise measurements. Int J Adv Manuf Technol 88(1–4):789–800CrossRefGoogle Scholar
  2. 2.
    Jin Tan, Yi Jun, Li Ping (2017) Temperature distributions in form grinding of involute gears. Int J Adv Manuf Technol 88:2609–2620CrossRefGoogle Scholar
  3. 3.
    Jin T, Yi J (2016) Investigation on the grinding force, power and heat flux distributions along the tooth profile in form grinding of gears. In: Proceedings of the ASME 2016 international manufacturing science and engineering conference MSEC2016, 27 June–1 July 2016, Blacksburg, Virginia, USAGoogle Scholar
  4. 4.
    Patil P (2017) FEM simulation and analysis of temperature field of environmental friendly MQL grinding. In: Proceedings of the international conference on communication and signal processing 2016 (ICCASP 2016), pp 182–186Google Scholar
  5. 5.
    Wang L, Tian X, Liu Q et al (2017) Experimental study and theoretical analysis of the form grinding of gears using new type micro-crystal corundum grinding wheels. Int J Adv Manuf Technol 92:1659–1669CrossRefGoogle Scholar
  6. 6.
    Rena XZ, Hu HF (2014) Analysis on the temperature field of gear form grinding. Appl Mech Mater 633–634:809–812Google Scholar
  7. 7.
    Klocke F, Schlattmeier H (2004) Surface damage caused by gear profile grinding and its effects on flank grinding and its effects on flank load carrying capacity. Gear Technol 44–53Google Scholar
  8. 8.
    Golgels C, Schlattmeier H, Klocke F (2006) Optimization of the gear profile grinding process utilizing an analogy process. Gear Technol 34–40Google Scholar
  9. 9.
    Klocke F (2009) Manufacturing process 2. Grinding, Honning, Lapping (trans: Kuchle A). Springer, BerlinGoogle Scholar
  10. 10.
    Jaeger JC (1942) Moving sources of heat and temperature at sliding contact. Proc R Soc NSW 76:203–224Google Scholar
  11. 11.
    Sipaylov VA (1978) Teplovye protsessy pri shlifovanii i upravlenie kachestvom poverkhnosti (Thermal processes during grinding and surface quality control). Mashinostroenie, MoscowGoogle Scholar
  12. 12.
    Larshin VP (1986) Primenenie resheniy teplofizicheskikh zadach k raschetu temperatury i glubiny defektnogo sloya pri shlifovanii (Application of solutions of thermophysical problems to the calculation of the temperature and depth of the defective layer during grinding). In: Interuniversity collection of scientific works, PermGoogle Scholar
  13. 13.
    Carslaw HS, Jaeger JC (1959) Conduction of heat in solids, 2nd edn. Oxford University PressGoogle Scholar
  14. 14.
    Karpuschewski B, Knoche H-J, Hipke M (2008) Gear finishing by abrasive processes. CIRP Ann 57:621–640CrossRefGoogle Scholar
  15. 15.
    Turich A, Kobialka C, Vucetic D (2009) Innovative concepts for grinding wind power energy gear. Gear Technol 39–44Google Scholar
  16. 16.
    Turich A (2010) Producing profile and lead modifications in threaded wheel and profile grinding. Gear Technol 54–62Google Scholar
  17. 17.
    Skoczylas Leszek, Tomczewski Leszek (2013) The application of universal CNC machine tool for spur gears manufacturing. Adv Sci Technol Res J 7(19):75–78CrossRefGoogle Scholar
  18. 18.
    Nishimura Y, Katsuma T, Ashizawa Y et al (2008) Gear grinding processing developed for high-precision gear manufacturing. Mitsubishi Heavy Industries, Ltd. Tech Rev 45(3):33–38Google Scholar
  19. 19.
    Inasaki I (1991) Monitoring and optimization of internal grinding process. Ann CIRP 40(1):359–362CrossRefGoogle Scholar
  20. 20.
    Inasaki I (1999) Sensor fusion for monitoring and controlling grinding processes. Int J Adv Manuf Technol 15:730–736CrossRefGoogle Scholar
  21. 21.
    Tonshoff HK, Friemuthand T, Becke C (2002) Process monitoring in grinding. Ann CIRP 51(2):551–569CrossRefGoogle Scholar
  22. 22.
    Zhao Z, Hou C, Duan S (2012) Online intelligent monitoring system of grinding process based on process modeling. In: Second international conference on instrumentation & measurement, computer, communication and control, pp 327–330Google Scholar

Copyright information

© Springer Nature Switzerland AG 2019

Authors and Affiliations

  1. 1.Odessa National Academy of Food TechnologiesOdessaUkraine
  2. 2.Odessa National Polytechnic UniversityOdessaUkraine

Personalised recommendations