Advertisement

Development of Bearing Beam and Seal System for Main Pumps

  • N. Berezhansky
  • A. Zaplatyn
  • R. Karymov
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

In this article, we consider the possibility of using an integrated bearing beam and seal system in the place of classic separate bearing assemblies and mechanical seals for main pumps. The classification of possible states of main pumps is given taking into account the most characteristic types of incidents, failures, and accidents. As a result of the analysis (which was realized in this article), it was established that the most vulnerable components to failure are the bearing assemblies and mechanical seals, the specific number of failures of which is about 50% of the total number of main pumps failures. The main directions of the use of an integrated bearing beam and sealing system in the form of bearing and seal block (BSB) are indicated, the practical and scientific novelty of which consists in replacing the classical power unit of the pump equipped with rolling bearings on the bearing unit consisting of two single mechanical seals and a pair of plain bearings (radial and axis). This modernization allows increasing the life of main pump equipment, as well as its inter-repair interval. At the same time, it is ensured not only an increase in the reliability of the abovementioned bearing beam and seal system of the main pump but also an improvement in the quantitative indicators of reliability of the main pump remaining elements, in connection with the reduction of the overall vibrational and temperature background.

Keywords

Bearing Mechanical seat Main pump Turnaround interval Pipelines productivity 

References

  1. 1.
    Aizenstein M (1957) Centrifugal pumps for the oil industry. Leningrad, MoscowGoogle Scholar
  2. 2.
    Aralov O, Buyanov I, Mastobayev B, Berezhansky N, Bylinkin D (2016) The main provisions of the life cycle parameters optimization methodology of technological equipment. In: Science and technology of oil and petroleum products pipeline transportation, Moscow, pp 23–29Google Scholar
  3. 3.
    Belousov V, Goloshchapov, V, Lupinski V (1977) The determination of the reliability of the main pumps type NM. In: Pipeline transportation of oil Ufa, pp 166–171Google Scholar
  4. 4.
    Bukharov I, Bodrov V (2017) Investigation of vibrations of the piping when testing the main pumps great performance. In: Science and technology of oil and petroleum products pipeline transportation, Moscow, pp 84–93Google Scholar
  5. 5.
    Chermen O, Fedotov N (2003) The rolling bearings. Mashinostroenie, MoscowGoogle Scholar
  6. 6.
    Chiroblock P (2017) Double mechanical seals for centrifugal pumps CNS 38 CNS 60. In: Science in modern society. Ufa, pp 67–69Google Scholar
  7. 7.
    Chuprov N (2015) Evaluation of the efficiency of the pump seal NIP 2500–80. Ukhta State Technical University, Ukhta, pp 280–284Google Scholar
  8. 8.
    Crete B, Morozova N, Ryzhikov I. Savva V, Somov O. Suminov I. Appelfeld A (2014) Trampoliere nanostructured coatings for mechanical seals. Advertising and publishing center “TECHNOSPHERE”, Moscow, pp 56–65Google Scholar
  9. 9.
    Kiselyov G, Ryazanov S (1985) Maintenance and repair of pumping systems. Chemistry, MoscowGoogle Scholar
  10. 10.
    Kolpakov L (1988) Operation of main centrifugal pumps. USPTU, Ufa, pp 30–32Google Scholar
  11. 11.
    Korzh V, Salnikov A (2010) Operation and repair of equipment of pumping and compressor stations. USTU, UkhtaGoogle Scholar
  12. 12.
    Kumar B, Batakanov E (2015) Operation of pump and compressor stations. KazNTU, AlmatyGoogle Scholar
  13. 13.
    Kuznetsov V, Kuznetsov I, Achilov R (1996) The repair of a large axial and centrifugal pumps. Energoatomizdat, Moscow, pp 124–231Google Scholar
  14. 14.
    Kvasov G (2006) Major lines of development of pump manufacture for main pipeline transportation. Chem Petrol Eng, 570–575. Springer New York Consultants BureauGoogle Scholar
  15. 15.
    Logatchev V, Sanzharovsky Y (2015) Technology restoration and strengthening of plain bearings, for example of sleeve gear pump NSH-32U-2. Agric Energy Supply, 120–124. MoscowGoogle Scholar
  16. 16.
    Ogar P, Sheremeta R, Lhang D (2006) Integrity of metal-polymer joints and rough surfaces. Bratsk State University, BratskGoogle Scholar
  17. 17.
    Pavlova Z (2014) Determination of rate of pump shaft rotation speed change of the pumping aggregate at regulating the pumping mode taking into account the safety of the main pipeline operation. Tyumen Ind Univ, 70–75Google Scholar
  18. 18.
    Polyakov R, Popikov A (2013) Oil pump mounting group performability increase due to combination of rolling and sliding bearings. In: Oil and gas engineering, Ufa, pp 83–85Google Scholar
  19. 19.
    Semenkov Yd (2010) Operation of pumping equipment for pipeline transport. TSOGU, TyumenGoogle Scholar
  20. 20.
    Shirobokov P (2017) Double mechanical seals for centrifugal pumps CNS 38 CNS 60. Limited liability company “Aeterna”, Ufa, pp 67–69Google Scholar
  21. 21.
    Sosnavsky S (2014) Effect of rotor beats on slot seals of oil main-line pumps. Allerton Press Inc. (New York), pp 89–92Google Scholar

Copyright information

© Springer Nature Switzerland AG 2019

Authors and Affiliations

  1. 1.Ufa State Petroleum Technical UniversityUfaRussia
  2. 2.OOO “Anod-Ural”UfaRussia

Personalised recommendations