Advertisement

Understanding Creep-Fatigue Interaction in Fe-25Ni-20Cr (wt%) Austenitic Stainless Steel

  • N. Kumar
  • A. Alomari
  • K. L. Murty
Conference paper
Part of the Conference Proceedings of the Society for Experimental Mechanics Series book series (CPSEMS)

Abstract

Gen-IV nuclear reactors require materials to operate under much harsher conditions necessitating the development of advanced structural materials. Sodium-cooled Fast Reactor (SFR) is a Gen-IV nuclear reactor with a high level of technology readiness. Alloy 709, Fe-25Ni-20Cr (wt%) alloyed with Nb and stabilized with nitrogen, is an advanced austenitic stainless steel having promising set of properties for SFRs. However, the creep-fatigue deformation behavior is unknown for this alloy. This work focuses on evaluating creep-fatigue interaction in this alloy. We report here a creep-fatigue study conducted at 750 °C using triangular waveform following the ASTM standard E2714–13 at 0.1 Hz frequency. The creep-fatigue tests were conducted in strain-controlled mode where strain amplitudes of 0.2% and 0.5% were used. The microstructural examination in as-received and post-deformation conditions were carried out using scanning and transmission electron microscopes. The creep-fatigue lives at 0.2% and 0.5% strain amplitudes were 17,416 and 526 cycles, respectively. The comparison of the TEM micrographs between as-received and creep-fatigue deformed at 0.5% strain amplitude showed higher dislocation density and loosely defined subgrains in the deformed alloy. The fractographs indicated that for the samples deformed at 0.2% strain amplitude, fatigue might have been the dominant mode of deformation whereas for the sample deformed at 0.5% strain amplitude, fatigue and creep both might have contributed to the overall deformation of the alloy.

Keywords

Austenitic stainless steel Gen-IV nuclear reactor Mechanical properties Creep-fatigue Plastic deformation 

Notes

Acknowledgements

The authors would like to acknowledge the financial support through award DOE/NEUP project #15-8582 for this work. The authors would also like to acknowledge the use of microscopy facility at Advanced Instrumentation Facility at North Carolina State University Raleigh USA.

References

  1. 1.
    Zinkle, S.J., Busby, J.T.: Structural materials for fission & fusion energy. Mater. Today. 12, 12–19 (2009)CrossRefGoogle Scholar
  2. 2.
    Zinkle, S.J., Was, G.S.: Materials challenges in nuclear energy. Acta Mater. 61, 735–758 (2013)CrossRefGoogle Scholar
  3. 3.
    Allen, T., Balbaud-Celerier, F., Asayama, T., Pouchon, M., Busby, J., Maloy, S., Park, J., Fazio, C., Dai, Y., Agostini, P.: Status Report on Structural Materials for Advanced Nuclear Systems. Organization for Economic Co-Operation and Development, France, NEA – 6409 (2013)Google Scholar
  4. 4.
    Dieter, G.E.: Mechanical Metallurgy, 3rd edn. McGraw-Hill, New York (1986)Google Scholar
  5. 5.
    Rodriguez, P., Rao, K.B.S.: Nucleation and growth of cracks and cavities under creep-fatigue interaction. Prog. Mater. Sci. 37, 403–480 (1993)CrossRefGoogle Scholar
  6. 6.
    Yagi, K., Kanemaru, O., Kubo, K., Tanaka, C.: Life prediction of 316 stainless steel under creep-fatigue loading. Fatigue Fract. Eng. Mater. Struct. 9, 395–408 (1987)CrossRefGoogle Scholar

Copyright information

© The Society for Experimental Mechanics, Inc. 2019

Authors and Affiliations

  • N. Kumar
    • 1
  • A. Alomari
    • 1
  • K. L. Murty
    • 1
  1. 1.Department of Nuclear EngineeringNorth Carolina State UniversityRaleighUSA

Personalised recommendations