Advertisement

Identification of Kinematic Points Based on KnC Measurements from the Suspension Motion Simulator

  • Chao LiuEmail author
  • Yi Zhang
  • Clemens Deubel
  • Felix Kocksch
  • Jan Kubenz
  • Günther Prokop
Conference paper
  • 5 Downloads
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

A systematic method to identify the kinematic point positions (x-, y- and z-values) of a rear axle has been developed with help of Kinematics and Compliance (KnC) measurements from the Suspension Motion Simulator (SMS) at TU Dresden. The kinematic points were at first measured with a ROMER arm, which is a coordinate measurement machine (CMM). The KnC simulation results of a MBS (Multibody System) model in ADAMS/Car based on CMM data were verified by KnC measurements from the SMS test rig. To reduce the calculation time, the total identification process was defined in two steps, rough and fine identification. In the first step of rough identification, the boundary conditions were constant lengths of links or constant distances between two kinematic points as to find possible spatial positions of kinematic points in a restricted range. For fine identification, the objective function considered also the KnC characteristic curve error between MBS simulations and test rig measurements, which was realized by a simulation exchange between ADAMS/Car and MATLAB. The errors between identified positions of kinematic points and CMM data were in an acceptable range, which has validated the developed identification method.

Keywords

Suspension Hardpoint Kinematic and Compliance Identification Multibody System (MBS) 

References

  1. 1.
    Rao, P., Roccaforte, D., Campbell, R., Zhou, H.: Developing an ADAMS® model of an automobile using test data. SAE Technical Paper 2002-01-1567 (2002)Google Scholar
  2. 2.
    Sancibrian, R., Garcia, P., Viadero, F., Fernandez, A., De-Juan, A.: Kinematic design of double-wishbone suspension systems using a multiobjective optimisation approach. Veh. Syst. Dyn. 48(7), 793–813 (2010)CrossRefGoogle Scholar
  3. 3.
    Mántaras, D.A., Luque, P.: Virtual test rig to improve the design and optimisation process of the vehicle steering and suspension systems. Veh. Syst. Dyn. 50(10), 1563–1584 (2012)CrossRefGoogle Scholar
  4. 4.
    Tey, J.Y., Ramli, R., Kheng, C.W., Chong, S.Y., Abidin, M.A.Z.: Identification of vehicle suspension parameters by design optimization. Eng. Optim. 46(5), 669–686 (2014)CrossRefGoogle Scholar
  5. 5.
    Rettweiler, P., Krings, R., Eckstein, L.: Neue Methode zur effizienten Parametrierung von MKS-Fahrzeugmodellen. ATZextra 21(2), 46–51 (2016)CrossRefGoogle Scholar
  6. 6.
    Best, T., Neads, S., Whitehead, J., Willows, I.: Design and operation of a new vehicle suspension kinematics and compliance facility. SAE Technical Paper 970096 (1997)Google Scholar
  7. 7.
    Holdmann, P., Köhn, P., Möller, B., Willems, R.: Suspension kinematics and compliance - measuring and simulation. SAE Technical Paper 980897 (1998)Google Scholar
  8. 8.
    Wei, T., Dorfi, H.: Vehicle suspension measurements evaluation of the benefits of dynamic over quasistatic kinematics and compliance testing. Tire Sci. Technol. 37(1), 32–46 (2009)CrossRefGoogle Scholar
  9. 9.
    Stachel, T.: Evolution of suspension development with K&C systems. In: MTS 2017 Worldwide K&C Users Group Meeting, Dresden, Germany (2017)Google Scholar
  10. 10.
    Reisner, M., Prokop, G., Langhoff, H., Krome, H.: K&C-based approach for examination of superposition errors. In: Proceedings of the 25th International Symposium on Dynamics of Vehicles on Roads and Tracks, IAVSD 2017, Rockhampton, Australia (2017)Google Scholar
  11. 11.
    Liu, C., Zhou, J., Gerhard, A., Kubenz, J., Prokop, G.: Characterization of the vehicle roll movement with the dynamic chassis simulator. In: Proceedings of Vehicle and Automotive Engineering 2, VAE 2018, Miskolc, Hungary (2018)Google Scholar
  12. 12.
    Liu, C., Deubel, C., Zhou, J., Gerhard, A., Kubenz, J., Prokop, G.: Experimental analysis of suspension kinematics and compliance characteristics of sensitivities and combined load cases with the suspension motion simulator. SAE Technical Paper 2019-01-0852 (2019)Google Scholar
  13. 13.
    Töpel, E., Büttner, K., Prokop, G., Penisson, C.: Methodical approaches for design of conventional and complex elastomer bearings in the suspension. In: 28th Aachen Colloquium Automobile and Engine Technology, Aachen, Germany (2019)Google Scholar
  14. 14.
  15. 15.
    Hall, A., McPhee, J.: Automation of Adams/Car K&C correlation using MATLAB. SAE Technical Paper 2014-01-0847 (2014)Google Scholar

Copyright information

© Springer Nature Switzerland AG 2020

Authors and Affiliations

  1. 1.Chair of Automotive EngineeringTechnische Universität DresdenDresdenGermany

Personalised recommendations