Advertisement

Fretting

  • Pawel PawlusEmail author
  • Andrzej Dzierwa
  • Agnieszka Lenart
Chapter
Part of the SpringerBriefs in Applied Sciences and Technology book series (BRIEFSAPPLSCIENCES)

Abstract

Fretting can be defined as a relative motion with a very small amplitude between two oscillating surfaces. Depending on the applied normal load and relative displacements, various sliding regimes can be identified: a partial slip and a gross slip. A fretting damage type is dependent on sliding regimes, and it leads to cracking (fretting fatigue) under a partial slip (lower amplitude) and wear damage under a gross slip (higher amplitude).

References

  1. 1.
    F. Akhtar, S.J. Guo, Microstructure, mechanical and fretting wear properties of TiC-stainless steel composites. Mater. Charact. 59, 84–90 (2008).  https://doi.org/10.1016/j.matchar.2006.10.021CrossRefGoogle Scholar
  2. 2.
    K.C. Budinsky, Effect of hardness differential on metal-to-metal fretting damage. Wear 301, 501–507 (2013).  https://doi.org/10.1016/j.wear.2013.01.003CrossRefGoogle Scholar
  3. 3.
    I.S. Cho, A. Amanov, D.H. Kwak et al., The influence of surface modification techniques on fretting wear of Al–Si alloy prepared by gravity die casting. Mater. Des. 65, 401–409 (2015).  https://doi.org/10.1016/j.matdes.2014.09.036CrossRefGoogle Scholar
  4. 4.
    K. Elleuch, S. Fouvry, Wear analysis of A357 aluminum alloy under fretting. Wear 253, 662–672 (2002).  https://doi.org/10.1016/S0043-1648(02)00116-3CrossRefGoogle Scholar
  5. 5.
    S. Fouvry, Ph Kapsa, L. Vincent, Analysis of sliding behavior for fretting loading: determination of transition criteria. Wear 185, 21–46 (1995).  https://doi.org/10.1016/0043-1648(94)06582-9CrossRefGoogle Scholar
  6. 6.
    S. Fouvry, Ph Kapsa, L. Vincent, Quantification of fretting damage. Wear 200, 186–205 (1996).  https://doi.org/10.1016/S0043-1648(96)07306-1CrossRefGoogle Scholar
  7. 7.
    Y. Fu, J. Wei, A.W. Batchelor, Some considerations on the mitigation of fretting damage by the application of surface-modification technologies. J. Mater. Process. Technol. 99, 231–245 (2000).  https://doi.org/10.1016/S0924-0136(99)00429-XCrossRefGoogle Scholar
  8. 8.
    Q. Hu, I.R. McColl, S.J. Harris et al., The role of debris in the fretting wear of a SiC reinforced aluminium alloy matrix composite. Wear 245, 10–21 (2000).  https://doi.org/10.1016/S0043-1648(00)00461-0CrossRefGoogle Scholar
  9. 9.
    W. Huang, B. Hou, Y. Pang et al., Fretting wear behavior of AZ91D and AM60B magnesium alloy. Wear 260, 1173–1178 (2006).  https://doi.org/10.1016/j.wear.2005.07.023CrossRefGoogle Scholar
  10. 10.
    M. Imai, H. Teramoto, Y. Shimauchi et al., Effect of oil supply on fretting wear. Wear 110, 217–225 (1986).  https://doi.org/10.1016/0043-1648(86)90099-2CrossRefGoogle Scholar
  11. 11.
    A. Iwabuchi, The role of oxide particles in the fretting wear of mild steel. Wear 151, 337–344 (1991).  https://doi.org/10.1016/0043-1648(91)90257-UCrossRefGoogle Scholar
  12. 12.
    T. Jibiki, M. Shima, T. Motoda et al., Role of surface micro-texturing in acceleration of initial running-in during lubricated fretting. Tribol. Online 5, 33–39 (2010).  https://doi.org/10.2474/trol.5.33CrossRefGoogle Scholar
  13. 13.
    M. Kalin, J. Vizintin, S. Novak, Effect of fretting conditions on the wear of silicon nitride against bearing steel. Mater. Sci. Eng. A220, 191–199 (1996).  https://doi.org/10.1016/S0921-5093(96)10457-3CrossRefGoogle Scholar
  14. 14.
    M. Kalin, J. Vizintin, S. Novak et al., Wear mechanisms in oil-lubricated and dry fretting of silicon nitride against bearing steel contacts. Wear 210, 27–38 (1997).  https://doi.org/10.1016/S0043-1648(97)00082-3CrossRefGoogle Scholar
  15. 15.
    H.K. Ki, Y.H. Lee, S.P. Heo, Mechanical and experimental investigation on nuclear fuel fretting. Tribol. Int. 39, 1305–1319 (2006).  https://doi.org/10.1016/j.triboint.2006.02.027CrossRefGoogle Scholar
  16. 16.
    K. Kim, Fretting studies on electroplated brass contacts. Int. J. Mech. Sci. 140, 306–312 (2018).  https://doi.org/10.1016/j.ijmecsci.2018.03.012CrossRefGoogle Scholar
  17. 17.
    K.J. Kubiak, M. Bigerelle, T.G. Mathia et al., Roughness of interface in dry contact under fretting conditions, in Proceedings on the 13th International Conference on Metrology and Properties of Engineering Surfaces, Twickenham Stadium, UK, 12–15 April 2011Google Scholar
  18. 18.
    K.J. Kubiak, T.E. Liskiewicz, T.G. Mathia, Surface morphology in engineering applications: Influence of roughness on sliding and wear in dry fretting. Tribol. Int. 44, 1427–1432 (2011).  https://doi.org/10.1016/j.triboint.2011.04.020CrossRefGoogle Scholar
  19. 19.
    K.J. Kubiak, T.G. Mathia, Influence of roughness on contact interface in fretting under dry and boundary lubricated sliding regimes. Wear 267, 315–321 (2009).  https://doi.org/10.1016/j.wear.2009.02.011CrossRefGoogle Scholar
  20. 20.
    K.J. Kubiak, T.G. Mathia, S. Fouvry, Interface roughness effect on friction map under fretting contact conditions. Tribol. Int. 43, 1500–1507 (2010).  https://doi.org/10.1016/j.triboint.2010.02.010CrossRefGoogle Scholar
  21. 21.
    L. Lee, E. Regis, S. Descartes et al., Fretting wear behavior of Zn–Ni alloy coatings. Wear 330–331, 112–121 (2015).  https://doi.org/10.1016/j.wear.2015.02.043CrossRefGoogle Scholar
  22. 22.
    E.R. Leheup, D. Zhang, J.R. Moon, Fretting wear of sintered iron under low normal pressure. Wear 221, 86–92 (1998).  https://doi.org/10.1016/S0043-1648(98)00265-8CrossRefGoogle Scholar
  23. 23.
    J.D. Lemm, A.R. Warmuth, S.R. Pearson et al., The influence of surface hardness on the fretting wear of steel pairs—its role in debris retention in contact. Tribol. Int. 81, 258–266 (2015).  https://doi.org/10.1016/j.triboint.2014.09.003CrossRefGoogle Scholar
  24. 24.
    A. Lenart, P. Pawlus, A. Dzierwa, The effect of steel disc surface texture in contact with ceramic ball on friction and wear in dry fretting. Surf. Topogr. Metrol. Prop. 6(3), 034004 (2018).  https://doi.org/10.1088/2051-672X/aac1a2Google Scholar
  25. 25.
    A. Lenart, P. Pawlus, A. Dzierwa et al., The effect of surface topography on dry fretting in the gross slip regime. Arch. Civ. Mech. Eng. 17(4), 894–904 (2017).  https://doi.org/10.1016/j.acme.2017.03.008CrossRefGoogle Scholar
  26. 26.
    A. Lenart, P. Pawlus, A. Dzierwa et al., The effect of wear debris removal on the fretting of rough surfaces. Tribologia 4, 47–54 (2017).  https://doi.org/10.5604/01.3001.0010.5993CrossRefGoogle Scholar
  27. 27.
    A. Lenart, P. Pawlus, S. Wos et al., The effect of surface texturing on dry gross fretting. Lubricants 6, 92 (2018).  https://doi.org/10.3390/lubricants6040092CrossRefGoogle Scholar
  28. 28.
    B.D. Leonard, F. Sadeghi, S. Shinde et al., Rough surface and damage mechanics under wear modeling using the combined finite-discrete element method. Wear 305, 312–321 (2013).  https://doi.org/10.1016/j.wear.2012.12.034CrossRefGoogle Scholar
  29. 29.
    J. Li, Y.H. Lu, Effects of displacement amplitude on fretting wear behaviors and mechanism of Inconel 600 Alloy. Wear 304, 223–230 (2013).  https://doi.org/10.1016/j.wear.2013.04.027CrossRefGoogle Scholar
  30. 30.
    L. Li, I. Etsion, F.E. Talke, The effect of frequency on fretting in a micro-spherical contact. Wear 270, 857–865 (2011).  https://doi.org/10.1016/j.wear.2011.02.014CrossRefGoogle Scholar
  31. 31.
    Q.Y. Liu, Z.R. Zhou, Effect of displacement amplitude in oil-lubricated fretting. Wear 239, 237–243 (2000).  https://doi.org/10.1016/S0043-1648(00)00323-9CrossRefGoogle Scholar
  32. 32.
    W. Lu, P. Zhang, X. Liu et al., Influence of surface topography on torsional fretting under flat-on-flat contact. Tribol. Int. 109, 367–372 (2017).  https://doi.org/10.1016/j.triboint.2017.01.001CrossRefGoogle Scholar
  33. 33.
    M. Odfalk, O. Vingsbo, Influence of normal force and frequency on fretting. Tribol. Trans. 33, 604–610 (1990).  https://doi.org/10.1080/10402009008981995CrossRefGoogle Scholar
  34. 34.
    N. Ohmae, T. Tsukizoe, The effect of slip amplitude on fretting. Wear 27, 281–294 (1974).  https://doi.org/10.1016/0043-1648(74)90114-8CrossRefGoogle Scholar
  35. 35.
    M. Okamoto, T. Jibiki, S. Ito et al., Role of cross-grooved type texturing in acceleration of initial running-in under lubricated fretting. Tribol. Int. 100, 126–131 (2016).  https://doi.org/10.1016/j.triboint.2015.12.012CrossRefGoogle Scholar
  36. 36.
    Y.W. Park, G.R. Bapu, K.Y. Lee, Studies of tin coated brass contacts in fretting conditions under different loads and frequencies. Surf. Coat. Technol. 201, 7939–7951 (2007).  https://doi.org/10.1016/j.surfcoat.2007.03.039CrossRefGoogle Scholar
  37. 37.
    Y.W. Park, T.S. Narayanan, K.Y. Lee, Effect of fretting amplitude and frequency on the fretting corrosion behavior of thin plated contacts. Surf. Coat. Technol. 201, 2181–2192 (2006).  https://doi.org/10.1016/j.surfcoat.2006.03.031CrossRefGoogle Scholar
  38. 38.
    P. Pawlus, R. Michalczewski, A. Lenart et al., The effect of random surface topography height on fretting in dry gross slip conditions. Proc. Inst. Mech. Eng. J J. Eng. 228, 1374–1391 (2014).  https://doi.org/10.1177/1350650114539467CrossRefGoogle Scholar
  39. 39.
    K. Pereira, T. Yue, M.A. Wahab, Multiscale analysis of the effect of roughness on fretting wear. Tribol. Int. 110, 222–231 (2017).  https://doi.org/10.1016/j.triboint.2017.02.024CrossRefGoogle Scholar
  40. 40.
    B. Raeymaekers, F.E. Talke, The effect of laser polishing on fretting wear between a hemisphere and a flat plate. Wear 269, 416–423 (2010).  https://doi.org/10.1016/j.wear.2010.04.027CrossRefGoogle Scholar
  41. 41.
    R. Ramesh, R. Gnanamoorthy, Effect of hardness on fretting behavior of structural steel. Mater. Des. 28, 1447–1452 (2007).  https://doi.org/10.1016/j.matdes.2006.03.020CrossRefGoogle Scholar
  42. 42.
    J. Sato, M. Shima, T. Sugawara et al., Effect of lubricants on fretting wear of steel. Wear 125, 83–95 (1988).  https://doi.org/10.1016/0043-1648(88)90195-0CrossRefGoogle Scholar
  43. 43.
    M. Shima, H. Suetake, I.R. McColl et al., On the behaviour of an oil lubricated fretting contact. Wear 210, 304–310 (1997).  https://doi.org/10.1016/S0043-1648(97)00078-1CrossRefGoogle Scholar
  44. 44.
    S. Soderberg, U. Bryggman, T. McCullough, Frequency effects in fretting wear. Wear 110, 19–34 (1986).  https://doi.org/10.1016/0043-1648(86)90149-3CrossRefGoogle Scholar
  45. 45.
    L. Toth, The investigation of the steady stage of steel fretting. Wear 20, 277–286 (1972).  https://doi.org/10.1016/0043-1648(72)90409-7CrossRefGoogle Scholar
  46. 46.
    M. Varenberg, I. Etsion, E. Altus, Theoretical substantiation of the slip index approach to fretting. Tribol. Lett. 19, 263–264 (2005).  https://doi.org/10.1007/s11249-005-7442-8CrossRefGoogle Scholar
  47. 47.
    M. Varenberg, I. Etsion, G. Halperin, Slip index: a new unified approach to fretting. Tribol. Lett. 17(3), 569–573 (2004).  https://doi.org/10.1023/B:TRIL.0000044506.98760.f9CrossRefGoogle Scholar
  48. 48.
    M. Varenberg, G. Halperin, I. Etsion, Different aspects of the role of wear debris in fretting wear. Wear 252, 902–910 (2002).  https://doi.org/10.1016/S0043-1648(02)00044-3CrossRefGoogle Scholar
  49. 49.
    O. Vingsbo, S. Soerberg, On fretting maps. Wear 126, 131–147 (1988).  https://doi.org/10.1016/0043-1648(88)90134-2CrossRefGoogle Scholar
  50. 50.
    D. Wang, D. Zhang, S. Ge, Effect of displacement amplitude on fretting fatigue behavior of hoisting rope wires in low cycle fatigure. Tribol. Int. 52, 178–189 (2012).  https://doi.org/10.1016/j.triboint.2012.04.008CrossRefGoogle Scholar
  51. 51.
    Z.A. Wang, Z.R. Zhou, An investigation of fretting behaviour of several synthetic base oils. Wear 267, 1399–1404 (2009).  https://doi.org/10.1016/j.wear.2008.12.092CrossRefGoogle Scholar
  52. 52.
    A.R. Warmuth, W. Sun, P.H. Shipway, The roles of contact conformity, temperature and displacement amplitude on the lubricated fretting wear of a steel-on-steel contact. R. Soc. Open Sci. 3, 150637 (2016).  https://doi.org/10.1098/rsos.150637CrossRefGoogle Scholar
  53. 53.
    Y. Yoon, I. Etsion, F.E. Talke, The evolution of fretting wear in a micro-spherical contact. Wear 270, 567–575 (2011).  https://doi.org/10.1016/j.wear.2011.01.013CrossRefGoogle Scholar
  54. 54.
    J. Yu, L. Qian, B. Yu et al., Nanofretting behavior of monocrystalline silicon (1 0 0) against SiO2 microsphere in vacuum. Tribol. Lett. 34, 31–40 (2009).  https://doi.org/10.1007/s11249-008-9385-3CrossRefGoogle Scholar
  55. 55.
    Z.R. Zhou, E. Sauger, J.J. Liu et al., Nucleation and early growth of tribologically transformed structure (TTS) induced by fretting. Wear 212, 50–58 (1997).  https://doi.org/10.1016/S0043-1648(97)00141-5CrossRefGoogle Scholar
  56. 56.
    Z.R. Zhou, S. Nakazawa, M.H. Zhu et al., Progress in fretting maps. Tribol. Int. 39, 1068–1073 (2006).  https://doi.org/10.1016/j.triboint.2006.02.001CrossRefGoogle Scholar
  57. 57.
    Z.R. Zhou, L. Vincent, Mixed fretting regimes. Wear 181–183, 531–536 (1995).  https://doi.org/10.1016/0043-1648(95)90168-XCrossRefGoogle Scholar
  58. 58.
    Z.R. Zhou, L. Vincent, Lubrication in fretting—a review. Wear 225–229, 962–967 (1999).  https://doi.org/10.1016/S0043-1648(99)00038-1CrossRefGoogle Scholar

Copyright information

© The Author(s), under exclusive license to Springer Nature Switzerland AG 2020

Authors and Affiliations

  1. 1.Department of Manufacturing Processes and Production EngineeringRzeszów University of TechnologyRzeszówPoland
  2. 2.Department of Manufacturing Processes and Production EngineeringRzeszów University of TechnologyRzeszówPoland
  3. 3.EME Aero Sp. z o. o.JasionkaPoland

Personalised recommendations