Advertisement

Investigation of Properties of Mg and Al Based Nano Hybrid-Metallic Composites Processed Through Liquid Processing Technique

  • Shubham SharmaEmail author
  • Mandeep Singh
  • N. Jayaram-Babu
  • Kalagadda Venkateswara Rao
  • Jujhar Singh
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

This research paper provides comprehensive and extraordinary efforts to carry out novel mechanical behaviour, corrosion testing and metallurgical characterization of aluminium alloy (Al-6061) and Magnesium alloy (Mg-AZ91D) reinforced nano-hybrid metallic composites processed using the liquid processing stir casting technique. These stir casted hybrid nano-metallic composites were manufactured using nano size reinforcements that are SiC, Graphite and Alumina of a size of ~100 nm. The finding of comparative results of casted composites was done by using potentio-dynamic polarization tests in the form of capacitance performance of dielectric properties. The results were reported out and the best results were achieved for aluminium reinforced graphite based composites with better corrosion behaviour performances and high hardness and tensile value of the fabricated composites. The experimental data for Mg-Graphite/ SiC/Al2O3 alloy show good arc-like performance over the frequency range with less impedance. The results also illustrated the good arc-like/weber behaviour over the frequency range examined, and indicate decent corrosion behaviour.

Keywords

Nano-hybrid metallic composites Stir casting Aluminium alloy Magnesium alloy Potentio-dynamic polarization tests Capacitance performance Dielectric properties 

References

  1. 1.
    Sharma, S., Sharma, S.: Critical review on processing and properties of magnesium matrix composites. J. Mater. Sci. Surf. Eng. 5(7), 696–700 (2017)Google Scholar
  2. 2.
    Sharma, S., Sudhakara, P., Kumar, S.K.: Overview on vacuum assisted resin infusion molding technique: a novel approach for advanced composites fabrication for aircraft and automotive applications. Int. J. Adv. Res. Sci. Eng. 7(3), 393–402 (2018)Google Scholar
  3. 3.
    Kannan, C., Ramanujam, R.: Comparative study on the mechanical and microstructural characterisation of AA 7075 nano and hybrid nano-composites produced by stir and squeeze casting. J. Adv. Res. 8(4), 309–319 (2017)CrossRefGoogle Scholar
  4. 4.
    Mohanavel, V., Rajan, K., Senthil, P.V., Arul, S.: Mechanical behaviour of hybrid composite (AA6351+Al2O3+Gr) fabricated by stir casting method. Mater. Today 4(2), 3093–3101 (2017)Google Scholar
  5. 5.
    Kandpal, B.C., Kumar, J., Singh H.: Fabrication and characterization of Al2O3/Al alloy 6061 composites fabricated by stir casting. Mater. Today 4(2), 2783–2792 (2017)Google Scholar
  6. 6.
    Liu, J., Li, J., Xu, C.: Interaction of the cutting tools and the ceramic-reinforced metal matrix composites during micro-machining: a review. CIRP J. Manufact. Sci. Technol. 7, 55–70 (2014)CrossRefGoogle Scholar
  7. 7.
    Reddy, A.P., Krishna, P.V., Rao, R.N., Murthy, N.V.: Silicon carbide reinforced aluminium metal matrix nano composites—a review. Mater. Today 4, 3959–3971 (2017)Google Scholar
  8. 8.
    Kumar, D.S., Sasanka, C.T., Ravindra, K., Suman, K.N.S.: Magnesium and its alloys in automotive applications—a review. Am. J. Mater. Sci. Technol. 4(1), 12–30 (2015).  https://doi.org/10.7726/ajmst.2015.1002CrossRefGoogle Scholar
  9. 9.
    Mukhopadhyay, P.: Alloy designation, processing, and use of AA6XXX series aluminium alloys. ISRN Metall. 2012, Article ID 165082, 15 (2012).  https://doi.org/10.5402/2012/165082CrossRefGoogle Scholar
  10. 10.
    Stojanovic, B., Babic, M., Mitrovic, S., Vencl, A., Miloradovic, N., Pantic, M.: Tribological characteristics of aluminium hybrid composites reinforced with silicon carbide and graphite. A review. J. Balkan Tribological Assoc. 19(1), 83–96 (2013)Google Scholar
  11. 11.
    Nino, A., Nakaibayashi, Y., Sugiyama, S., Taimatsu, H.: Microstructure and mechanical properties of WC-SiC composites. Mater. Trans. 52(8), 1641–1645 (2011)CrossRefGoogle Scholar
  12. 12.
    Wei, R.P.: A model for particle-induced pit growth in aluminum alloys. Scr. Mater. 44(11), 2647–2652 (2001)CrossRefGoogle Scholar
  13. 13.
    Bodunrin, M.O., Alaneme, K.K., Chown, L.H.: Aluminium matrix hybrid composites: a review of reinforcement philosophies; mechanical, corrosion and tribological characteristics. J. Mater. Res. Technol. 4(4), 434–445 (2015)CrossRefGoogle Scholar
  14. 14.
    Radhika, N., Subramanian, R., Prasat, S.V.: Tribological behaviour of aluminium/alumina/graphite hybrid metal matrix composite using Taguchi’s techniques. J. Miner. Mater. Charact. Eng. 10(5), 427–443 (2011)Google Scholar
  15. 15.
    Rohatgi, P.K.: Metal-matrix composites. Defence Sci. J. 43(4), 323–349 (2013)CrossRefGoogle Scholar
  16. 16.
    Dash, D., Samanta, S., Rai, R.N.: Study on fabrication of magnesium based metal matrix composites and its improvement in mechanical and tribological properties—a review. In: IOP Conference Series: Materials Science and Engineering, vol. 377, p. 012133 (2018).  https://doi.org/10.1088/1757-899x/377/1/012133CrossRefGoogle Scholar
  17. 17.
    Moona, G., Walia, R.S., Rastogi, V., Sharma, R.: Aluminium metal matrix composites: a retrospective investigation. Indian J. Pure Appl. Phys. 56, 164–175 (2018)Google Scholar
  18. 18.
    Jurwall, V., Pandey, A., Sharma, A.K.: Fabrication of Nano Hybrid Metal Matrix Composites through Stir Casting Route: A Review. In: IOP Conference Series: Materials Science and Engineering, vol. 377, p. 012142, 1–6 (2018).  https://doi.org/10.1088/1757-899x/377/1/012142CrossRefGoogle Scholar
  19. 19.
    Tarelnyk, V., Martsynkovskyy, V., Gaponova, O., et al.: New sulphiding method for steel and cast iron parts. In: IOP Conference Series: Materials Science and Engineering, vol. 233, 012049 (2017).  https://doi.org/10.1088/1757-899x/233/1/012049CrossRefGoogle Scholar
  20. 20.
    Zabolotnyi, O., Sychuk, V., Somov, D.: Obtaining of porous powder materials by radial pressing method. In: Ivanov, V., et al. (eds.) Advances in Design, Simulation and Manufacturing. DSMIE 2018. Lecture Notes in Mechanical Engineering, pp. 186–198 (2019).  https://doi.org/10.1007/978-3-319-93587-4_20Google Scholar
  21. 21.
    Berladir, K.V., Hovorun, T.P., Bilous, O.A., Baranova, S.V.: The modeling of the composition and properties of functional materials based on polytetrafluoroethylene. Funct. Mater. 25(2), 342–347 (2018)CrossRefGoogle Scholar
  22. 22.
    Tarelnyk, V., Martsynkovskyy, V., Gaponova, O., et al.: New sulphiding method for steel and cast iron parts. In: IOP Conference Series: Materials Science and Engineering, vol. 233, p. 012049 (2017).  https://doi.org/10.1088/1757-899x/233/1/012049CrossRefGoogle Scholar
  23. 23.
    Antoszewski, B., Tarelnyk, V.: Laser texturing of sliding surfaces of bearings and pump seals. In: Applied Mechanics and Materials, vol. 630, pp. 301–307 (2014).  https://doi.org/10.4028/www.scientific.net/AMM.630.301CrossRefGoogle Scholar
  24. 24.
    Panchenko, A., Voloshina, A., Kiurchev, S., et al.: Development of the universal model of mechatronic system with a hydraulic drive. East. Eur. J. Enterp. Technol. 4(7(94)), 51–60 (2018).  https://doi.org/10.15587/1729-4061.2018.139577CrossRefGoogle Scholar
  25. 25.
    Pavlenko, I., Trojanowska, J., Gusak, O., et al.: Estimation of the reliability of automatic axial-balancing devices for multistage centrifugal pumps. Periodica Polytech. Mech. Eng. 63(1), 52–56 (2019).  https://doi.org/10.3311/PPme.12801CrossRefGoogle Scholar
  26. 26.
    Sychuk, V., Zabolotnyi, O., McMillan, A.: Developing new design and investigating porous nozzles for abrasive jet machine. Powder Metall. Met. Ceram. 53(9–10), 600–605 (2015).  https://doi.org/10.1007/s11106-015-9655-1CrossRefGoogle Scholar
  27. 27.
    Trojanowska, J., Kolinski, A., Galusik, D., et al.: A methodology of improvement of manufacturing productivity through increasing operational efficiency of the production process. In: Hamrol, A., Ciszak, O., Legutko, S., Jurczyk, M. (eds.) Advances in Manufacturing. Lecture Notes in Mechanical Engineering, pp. 23–32. Springer, Cham (2018)Google Scholar
  28. 28.
    Povstyanoi, O.Y., Sychuk, V.A., McMillan, A., et al.: Metallographic analysis and microstructural image processing of nozzles for sandblasting produced by powder metallurgy methods. Powder Metall. Met. Ceram. 54(3–4), 234–240 (2015).  https://doi.org/10.1007/s11106-015-9705-8CrossRefGoogle Scholar
  29. 29.
    Pavlenko, I., Simonovskiy, V., Ivanov, V., et al.: Implementation of artificial neural network for identification of bearing stiffness characteristics according to the research of critical frequencies of the rotor. In: Ivanov, V., et al. (eds.) Advances in Design, Simulation and Manufacturing. DSMIE-2018. Lecture Notes in Mechanical Engineering, pp. 325–335 (2019).  https://doi.org/10.1007/978-3-319-93587-4_34Google Scholar

Copyright information

© Springer Nature Switzerland AG 2020

Authors and Affiliations

  1. 1.CSIR-Central Leather Research Institute, Regional Centre for Extension & DevelopmentJalandharIndia
  2. 2.School of Mechanical and Mechatronics EngineeringUniversity of Technology Sydney (UTS)SydneyAustralia
  3. 3.Centre for Nanoscience and Technology, IST, JNTUHHyderabadIndia
  4. 4.IK Gujral Punjab Technical UniversityKapurthalaIndia

Personalised recommendations