Advertisement

Microstructural Analysis of Nickel-Based Composite Coatings and Their Effect on Micro-hardness and Nano-indentation Behavior

  • Rabah AzzougEmail author
  • Fatah Hellal
  • Yamina Mebdoua
Conference paper
Part of the Lecture Notes in Mechanical Engineering book series (LNME)

Abstract

The coating reliability and failure are inextricably linked to its microstructure, from which all the other characteristics are derived. Based on the properties obtained from multiscale assessments, after a thermal flame spraying processing applied on X18 carbon steel, this investigation aims at expounding the contribution of the prior grit blasting treatment and the presence of the Ni-based bonding layer in determining the coating characteristics. For that, a NiCrBSi self-fluxing alloy reinforced with tungsten carbides was selected to realize the deposits in the open atmosphere, using the acetylene as fuel. The characterization of the coating was carried out through optical microscopy, micro-hardness measurements and nano-indentation tests. Quantitative data were estimated by processing the obtained optical micrographs. The results show that the coating contains fine precipitates and has dendritic microstructure surrounded by a eutectic phase. The micro-hardness profile proved that the prior grit blasting treatment had induced a substrate hardening near the interface where the hardness roughly achieves 500HV. The cooling in the air environment has activated the initiation of cracks. The nano-indentation results reveal that the elastoplastic response of the matrix differs depending on the nature and the proportion of phases.

Keywords

Nickel-Based composite coatings Flame spraying Microstructure Micro-hardness Nano-indentation 

References

  1. Bezborodov VP, Yu NS (2016) Microstructure and mechanical properties of eutectic nickel alloy coatings. IOP Conf Ser: Mat Sci Eng 124(1):012119CrossRefGoogle Scholar
  2. Coddet C, Montavon G, Ayrault-Costil S, Freneaux O, Rigolet F, Barbezat G, Wazen P (1999) Surface preparation and thermal spray in a single step: The PROTAL process—example of application for an aluminum-base substrate. J Therm Spray Technol 8(2):235–242CrossRefGoogle Scholar
  3. Ettmayer P, Kolaska H, Ortner HM (2014) 1.01—history of hardmetals A2—Sarin, Vinod K. In: Comprehensive hard materials. Oxford, Elsevier, pp 3–27Google Scholar
  4. Fale S, Likhite A, Bhatt J (2015) Nanoindentation, compressive and tensile deformation study of in-situ Al–AlN metal matrix composites. Trans Indian Inst Met 68(2):291–297CrossRefGoogle Scholar
  5. Garrido MA, Rico A, Gómez MT, Cadenas M, Fernández-Rico JE, Rodríguez J (2017) Tribological and oxidative behavior of thermally sprayed NiCrBSi coatings. J Thermal Spray Technol, pp 1–13Google Scholar
  6. Hu C, Hou S (2017) Effects of rare earth elements on properties of Ni-base superalloy powders and coatings. Coatings 7(2):30CrossRefGoogle Scholar
  7. Islak S, Buytoz S (2013) Microstructure properties of HVOF-sprayed NiCrBSi/WCCo-based composite coatings on AISI 1040 steel. Optoelectron Adv Mat-Rapid Commun 7(11–12):900–903Google Scholar
  8. Iždinská Z, Nasher A, Iždinský K (2010) The structure and properties of composite laser clad coatings with Ni based matrix with WC particles. Materials Eng. 17(2):1Google Scholar
  9. Kontis P, Yusof HM, Pedrazzini S, Danaie M, Moore KL, Bagot PAJ, Reed RC (2016) On the effect of boron on grain boundary character in a new polycrystalline super-alloy. Acta Mater 103(Supplement C):688–699CrossRefGoogle Scholar
  10. Kontis P, Alabort E, Barba D, Collins DM, Wilkinson AJ, Reed RC (2017) On the role of boron on improving ductility in a new polycrystalline super-alloy. Acta Mater 124(Supplement C):489–500CrossRefGoogle Scholar
  11. Li C-J, Yang G-J (2013) Relationships between feedstock structure, particle parameter, coating deposition, microstructure and properties for thermally sprayed conventional and nanostructured WC–Co. Int J Refract Metal Hard Mater 39:2–17CrossRefGoogle Scholar
  12. Lin MC, Chang LS, Lin HC, Yang CH, Lin KM (2006) A study of high-speed slurry erosion of NiCrBSi thermal-sprayed coating. Surf Coat Technol 201(6):3193–3198CrossRefGoogle Scholar
  13. Lioma D, Sacks N, Botef I (2015) Cold gas dynamic spraying of WC–Ni cemented carbide coatings. Int J Refract Metal Hard Mater 49:365–373CrossRefGoogle Scholar
  14. Mebdoua Y, Fizi Y, Lahmar H (2017) Determination of elastic-plastic parameters of inconel arc sprayed coating. In: Boukharouba T, Pluvinage G, Azouaoui K (eds) Applied mechanics, behavior of materials, and engineering systems: selected contributions to the 5th Algerian congress of mechanics, CAM2015, El-Oued, Algeria, pp 193–203, 25–29 Oct 2017. Springer International Publishing, ChamGoogle Scholar
  15. Ren X, Miao H, Peng Z (2013) A review of cemented carbides for rock drilling: an old but still tough challenge in geo-engineering. Int J Refract Metal Hard Mater 39:61–77CrossRefGoogle Scholar
  16. Simunovic K, Slokar L, Havrlisan S (2017) SEM/EDS investigation of one-step flame sprayed and fused Ni-based self-fluxing alloy coatings on steel substrates. Phil Mag 97(4):248–268CrossRefGoogle Scholar
  17. Škamat J, Cernasejus O, Valiulis AV, Lukauskaite R, Visniakov N (2015) Improving hardness of Ni-Cr-Si-B-Fe-C thermal sprayed coatings through grain refinement by vibratory treatment during refusion. Mat Sci/Medziagotyra 1(2)Google Scholar
  18. Tarragó Cifre JM, Jiménez Piqué E, Turón Viñas M, Rivero L, Al-Dawery I, Schneider L, Llanes Pitarch LM (2014) Fracture and fatigue behavior of cemented carbides: 3D focused ion beam tomography of crack-microstructure interactions. Int J Powder Metall 50:1–10Google Scholar
  19. Otsubo F, Era H, Kishitake K (2000) Structure and phases in nickel-base self-fluxing alloy coating containing high chromium and boron. J Therm Spray Technol 9(1):107–113CrossRefGoogle Scholar
  20. Ozer A, Kriven WM, Tur YK (2011) An experimental study on the effects of SiC on the sintering and mechanical properties of Cr3C2-NiCR cermets. In: Mechanical properties and performance of engineering ceramics and composites VI. 2011, pp 271–279. WileyGoogle Scholar
  21. Pramanik A, Zhang LC, Arsecularatne JA (2008) Deformation mechanisms of MMCs under indentation. Compos Sci Technol 68(6):1304–1312CrossRefGoogle Scholar

Copyright information

© Springer Nature Switzerland AG 2019

Authors and Affiliations

  1. 1.Ecole Nationale Polytechnique, Département de MétallurgieLSGMAlgiersAlgeria
  2. 2.Centre de Développement des Technologies AvancéesAlgiersAlgeria

Personalised recommendations