Advertisement

The Design of Real Time Recording System for Electric Spark Source Parameters Based on the Internet of Things

  • Mingzhang Luo
  • Hao Zhang
  • Qiang LiuEmail author
  • Yang Xu
  • Chong Luo
  • Zhongyuan Wang
Conference paper
Part of the Lecture Notes in Computer Science book series (LNCS, volume 11280)

Abstract

The electric spark source is widely used in the fields of shallow surface exploration and earthquake prediction because of its environmental protection, rich spectrum and good consistency. However, most electric spark source is short of real time recording and control system for power parameters, so that its failure rate is quite high. This paper introduces a real-time power parameter recording system of electric spark source. It has the advantages of failure detection, fast fault location, and network extension. It can realize the remote control and monitoring, and has a strong popularization value.

Keywords

Electric spark source Power parameter recording Internet of things 

References

  1. 1.
    Pei, Y.L., Wang, K.Y., Liu, C.G., Li, X.S., Li, Z.G.: The sparker source charging technique. Ocean Technol. 26(03), 73–76 (2007)Google Scholar
  2. 2.
    Wu, X.L., Wang, J.M.: Research and Design of High Power Sparker. Yangtze University (2016)Google Scholar
  3. 3.
    Dai, X., Zhu, J., Haberman, M.R.: A focused electric spark source for non-contact stress wave excitation in solids. J. Acoust. Soc. Am. EL134(6), 513 (2013)CrossRefGoogle Scholar
  4. 4.
    Fan, A.L., Sun, Y.H., Xu, Z., et al.: Single channel electric spark source and discharge experimental study. Advanced Technology of Electrical Engineering & Energy (2016)Google Scholar
  5. 5.
    Fan, A., Sun, Y., Yan, P., et al.: Design on a kind of multi-channel electric spark source system. In: Industrial Electronics and Applications, pp. 2391–2394. IEEE (2016)Google Scholar
  6. 6.
    Xu, X., Sun, Y., Fu, R., et al.: Development of the solid-state modular land electric spark source. High Volt. Appar. 53(4), 36–40 (2017)Google Scholar
  7. 7.
    Liu, Q., Shao, H., Zhang, Y.: Study on shock waves induced by electric spark discharge. China Science paper (2016)Google Scholar
  8. 8.
    Yang, Z.Y., Xu, Z.L.: The digital measurement and wireless data transmission for power parameter. Electr. Meas. Instrum. 42(472), 34–37 (2005)Google Scholar
  9. 9.
    Guo, Y., Fu, Z.X.: Frequency measurement of AC sampling and implementation of tracking phase-locked method. Zidonghua Yu Yiqi Yibiao 12(03), 17–19 (2002)Google Scholar
  10. 10.
    Ye, J.Z., Yin, X.: Development and application of the power load parameter recording and monitoring system. Comput. Eng. 32(05), 247–248 (2006)Google Scholar
  11. 11.
    Zhang, C., Zhang, C.J., Wu, X.G.: Design and implementation of simple SD card driven method in MCU system. 28(04), 479–481+499 (2011)Google Scholar
  12. 12.
    Li, S.Q., Dong, H.B., Li, R.S.: Design of SD memory card based on FatFs file system. Meas. Control Technol. 30(12), 79–80 (2011)Google Scholar

Copyright information

© Springer Nature Switzerland AG 2018

Authors and Affiliations

  • Mingzhang Luo
    • 1
    • 2
  • Hao Zhang
    • 1
  • Qiang Liu
    • 3
    Email author
  • Yang Xu
    • 1
  • Chong Luo
    • 4
  • Zhongyuan Wang
    • 1
  1. 1.National Demonstration Center for Experimental Electrical and Electronic EducationYangtze UniversityJingzhouChina
  2. 2.Electronics and Information SchoolYangtze UniversityJingzhouChina
  3. 3.State Key Laboratory for Performance and Structural Safety of Petroleum Tubular Goods and Equipment Materials, CNPC Tubular Goods Research InstituteXi’anChina
  4. 4.Management SchoolYangtze UniversityJingzhouChina

Personalised recommendations