Abstract
In this article, we consider the possibility of using an integrated bearing beam and seal system in the place of classic separate bearing assemblies and mechanical seals for main pumps. The classification of possible states of main pumps is given taking into account the most characteristic types of incidents, failures, and accidents. As a result of the analysis (which was realized in this article), it was established that the most vulnerable components to failure are the bearing assemblies and mechanical seals, the specific number of failures of which is about 50% of the total number of main pumps failures. The main directions of the use of an integrated bearing beam and sealing system in the form of bearing and seal block (BSB) are indicated, the practical and scientific novelty of which consists in replacing the classical power unit of the pump equipped with rolling bearings on the bearing unit consisting of two single mechanical seals and a pair of plain bearings (radial and axis). This modernization allows increasing the life of main pump equipment, as well as its inter-repair interval. At the same time, it is ensured not only an increase in the reliability of the abovementioned bearing beam and seal system of the main pump but also an improvement in the quantitative indicators of reliability of the main pump remaining elements, in connection with the reduction of the overall vibrational and temperature background.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Aizenstein M (1957) Centrifugal pumps for the oil industry. Leningrad, Moscow
Aralov O, Buyanov I, Mastobayev B, Berezhansky N, Bylinkin D (2016) The main provisions of the life cycle parameters optimization methodology of technological equipment. In: Science and technology of oil and petroleum products pipeline transportation, Moscow, pp 23–29
Belousov V, Goloshchapov, V, Lupinski V (1977) The determination of the reliability of the main pumps type NM. In: Pipeline transportation of oil Ufa, pp 166–171
Bukharov I, Bodrov V (2017) Investigation of vibrations of the piping when testing the main pumps great performance. In: Science and technology of oil and petroleum products pipeline transportation, Moscow, pp 84–93
Chermen O, Fedotov N (2003) The rolling bearings. Mashinostroenie, Moscow
Chiroblock P (2017) Double mechanical seals for centrifugal pumps CNS 38 CNS 60. In: Science in modern society. Ufa, pp 67–69
Chuprov N (2015) Evaluation of the efficiency of the pump seal NIP 2500–80. Ukhta State Technical University, Ukhta, pp 280–284
Crete B, Morozova N, Ryzhikov I. Savva V, Somov O. Suminov I. Appelfeld A (2014) Trampoliere nanostructured coatings for mechanical seals. Advertising and publishing center “TECHNOSPHERE”, Moscow, pp 56–65
Kiselyov G, Ryazanov S (1985) Maintenance and repair of pumping systems. Chemistry, Moscow
Kolpakov L (1988) Operation of main centrifugal pumps. USPTU, Ufa, pp 30–32
Korzh V, Salnikov A (2010) Operation and repair of equipment of pumping and compressor stations. USTU, Ukhta
Kumar B, Batakanov E (2015) Operation of pump and compressor stations. KazNTU, Almaty
Kuznetsov V, Kuznetsov I, Achilov R (1996) The repair of a large axial and centrifugal pumps. Energoatomizdat, Moscow, pp 124–231
Kvasov G (2006) Major lines of development of pump manufacture for main pipeline transportation. Chem Petrol Eng, 570–575. Springer New York Consultants Bureau
Logatchev V, Sanzharovsky Y (2015) Technology restoration and strengthening of plain bearings, for example of sleeve gear pump NSH-32U-2. Agric Energy Supply, 120–124. Moscow
Ogar P, Sheremeta R, Lhang D (2006) Integrity of metal-polymer joints and rough surfaces. Bratsk State University, Bratsk
Pavlova Z (2014) Determination of rate of pump shaft rotation speed change of the pumping aggregate at regulating the pumping mode taking into account the safety of the main pipeline operation. Tyumen Ind Univ, 70–75
Polyakov R, Popikov A (2013) Oil pump mounting group performability increase due to combination of rolling and sliding bearings. In: Oil and gas engineering, Ufa, pp 83–85
Semenkov Yd (2010) Operation of pumping equipment for pipeline transport. TSOGU, Tyumen
Shirobokov P (2017) Double mechanical seals for centrifugal pumps CNS 38 CNS 60. Limited liability company “Aeterna”, Ufa, pp 67–69
Sosnavsky S (2014) Effect of rotor beats on slot seals of oil main-line pumps. Allerton Press Inc. (New York), pp 89–92
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer Nature Switzerland AG
About this paper
Cite this paper
Berezhansky, N., Zaplatyn, A., Karymov, R. (2019). Development of Bearing Beam and Seal System for Main Pumps. In: Radionov, A., Kravchenko, O., Guzeev, V., Rozhdestvenskiy, Y. (eds) Proceedings of the 4th International Conference on Industrial Engineering. ICIE 2018. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-319-95630-5_111
Download citation
DOI: https://doi.org/10.1007/978-3-319-95630-5_111
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-95629-9
Online ISBN: 978-3-319-95630-5
eBook Packages: EngineeringEngineering (R0)