Abstract
This paper presents a report about work in progress of research on the influence of the flow of SCFRC on the fiber orientations. Mechanical properties of the short steel fiber reinforced cementitious materials mostly depend on the fiber orientation and spatial dispersion. Many studies have shown that it is possible to achieve the desired fiber orientation by optimizing the parameters of rheological properties or the casting process. In order to improve the key mechanical properties, multiple statistical experiments with various factors are needed. This paper analyzes the influence of casting velocity and formwork surface quality on the fiber distribution and orientation. A suitable technique for our method was to replace Steel Fiber Reinforced Self-Compacting Concrete (SFRSCC) by a transparent polymer with similar rheological properties as SFRSCC. Preliminary analysis of the experimental results shows that the fibers tend to orient mostly perpendicular to the flow direction and turn their orientation longitudinally near the walls. Experiments showed that the fiber spatial distribution was affected by the casting velocity. Faster casting velocities provided more preferable homogeneous distribution. Moreover, the roughness of the bottom of the formwork demonstrated some influence on the fiber orientations but no significant impact on the spatial dispersion. In addition, we used the image analysis method to estimate fiber orientation and distribution.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Notes
- 1.
Orientation as in oriented in a (certain) direction.
- 2.
Alignment as in aligned with each other.
References
Beissel, R.A., Lim, H.: Self Compacting Concrete: Modern Concrete and Admixture Technology, pp. 607–612 (2000)
Brouwers, H.J.H., Radix, H.J.: Self-compacting concrete: theoretical and experimental study. Cem. Concr. Res. 35(11), 2116–2136 (2005)
Nawy, E.G., Edward, G.: Fundamentals of High-performance Concrete. Wiley (2001)
Balaguru, P.N., Shah, S.P.: Fiber-reinforced cement composites (1992)
Lawler, J.S., Zampini, D., Shah, S.P.: Permeability of cracked hybrid fiber-reinforced mortar under load. Mater. J. 99(4), 379–385 (2002)
Voigt, T., Van Bui, K., Shah, S.P.: Drying shrinkage of concrete reinforced with fibers and welded-wire fabric. Mater. J. 101(2), 233–241 (2004)
Mesbah, H.A., Buyle-Bodin, F.: Efficiency of polypropylene and metallic fibres on control of shrinkage and cracking of recycled aggregate mortars. Constr. Build. Mater. 13(8), 439–447 (1999)
Boulekbache, B., Hamrat, M., Chemrouk, M., Amziane, S.: Flowability of fibre-reinforced concrete and its effect on the mechanical properties of the material. Constr. Build. Mater. 24(9), 1664–1671 (2010)
Ponikiewski, T., Gołaszewski, J., Rudzki, M., Bugdol, M.: Determination of steel fibres distribution in self-compacting concrete beams using x-ray computed tomography. Arch. Civ. Mech. Eng. 15, 558–568 (2015)
Liu, J., Sun, W., Miao, C., Liu, J., Li, C.: Assessment of fiber distribution in steel fiber mortar using image analysis. J. Wuhan Univ. Technol. Mater. Sci. Ed. 27, 166–171 (2012)
Stähli, P., Custer, R., van Mier, J.G.M.: On flow properties, fibre distribution, fibre orientation and flexural behaviour of FRC. Mater. Struct. 41(1), 189–196 (2008)
Švec, O., Žirgulis, G., Bolander, J.E., Stang, H.: Influence of formwork surface on the orientation of steel fibres within self-compacting concrete and on the mechanical properties of cast structural elements. Cem. Concr. Compos. 50, 60–72 (2014)
Soroushian, P., Lee, C.-D.: Distribution and orientation of fibers in steel fiber reinforced concrete. Mater. J. 87, 433–439 (1990)
Grigaliunas, P., Kringelis, T.: SCC flow induced steel fiber distribution and orientation. Non-destructive inductive method. In: 11th European Conference on Non-Destructive Testing, Prague, Czech Republic (2014)
Herrmann, H., Lees, A.: On the influence of the rheological boundary conditions on the fibre orientations in the production of steel fibre reinforced concrete elements. Proc. Est. Acad. Sci. 65(4), 408–413 (2016). Open-Access CC-BY-NC 4.0
Promentilla, M.A.B., Sugiyama, T., Shimura, K.: Threedimensional imaging of cement-based materials with x-ray tomographic microscopy: visualization and quantification. In: International Conference on Microstructure Related Durability of Cementitious Composites, vol. 61, pp. 1357–1366 (2008)
Liu, J., Li, C., Liu, J., Cui, G., Yang, Z.: Study on 3D spatial distribution of steel fibers in fiber reinforced cementitious composites through micro-CT technique. Constr. Build. Mater. 48, 656–661 (2013)
Pastorelli, E., Herrmann, H.: Time-efficient automated analysis for fibre orientations in steel fibre reinforced concrete. Proc. Est. Acad. Sci. 65(1), 28–36 (2016)
Herrmann, H., Pastorelli, E., Kallonen, A., Suuronen, J.-P.: Methods for fibre orientation analysis of x-ray tomography images of steel fibre reinforced concrete (SFRC). J. Mater. Sci. 51(8), 3772–3783 (2016)
Suuronen, J.-P., Kallonen, A., Eik, M., Puttonen, J., Serimaa, R., Herrmann, H.: Analysis of short fibres orientation in steel fibre reinforced concrete (SFRC) using x-ray tomography. J. Mater. Sci. 48(3), 1358–1367 (2013)
Ferrara, L., Faifer, M., Toscani, S.: A magnetic method for non destructive monitoring of fiber dispersion and orientation in steel fiber reinforced cementitious composites–Part 1: method calibration. Mater. Struct., 1–15 (2011)
Karhunen, K., Seppänen, A., Lehikoinen, A., Monteiro, P.J.M., Kaipio, J.P.: Electrical resistance tomography imaging of concrete. Cem. Concr. Res. 40, 137–145 (2010)
Torrents, J.M., Blanco, A., Pujadas, P., Aguado, A., Juan-Garcia, P., Sánchez-Moragues, M.Á.: Inductive method for assessing the amount and orientation of steel fibers in concrete. Materi. Struct. 45, 1577–1592 (2012)
Schickert, M.: Progress in ultrasonic imaging of concrete. Mater. Struct. 38, 807–815 (2005)
Aggelis, D.G., Soulioti, D., Barkoula, N.M., Paipetis, A.S., Matikas, T.E., Shiotani, T.: Acoustic emission monitoring of steel-fiber reinforced concrete beams under bending. Prog AE 14, 287–294 (2008)
Keru, W., Chen, B., Yao, W.: Study on the ae characteristics of fracture process of mortar, concrete and steel-fiber-reinforced concrete beams. Cem. Concr. Res. 30(9), 1495–1500 (2000)
Soulioti, D., Barkoula, N.M., Paipetis, A., Matikas, T.E., Shiotani, T., Aggelis, D.G.: Acoustic emission behavior of steel fibre reinforced concrete under bending. Constr. Build. Mater. 23(12), 3532–3536 (2009)
Roussel, N., Gram, A., Cremonesi, M., Ferrara, L., Krenzer, K., Mechtcherine, V., Shyshko, S., Skocec, J., Spangenberg, J., Svec, O., Thrane, L.N., Vasilic, K.: Numerical simulations of concrete flow: a benchmark comparison. Cem. Concr. Res. 79, 265–271 (2016)
Svec, O., Skocek, J., Olesen, J.F., Stang, H.: Fibre reinforced self-compacting concrete flow simulations in comparison with l-box experiments using carbopol. In: 8th Rilem International Symposium on Fibre Reinforced Concrete (2012)
Ehrentraut, H., Muschik, W.: On symmetric irreducible tensors in d-dimensions. ARI Int. J. Phys. Eng. Sci. 51(2), 149–159 (1998)
Herrmann, H., Beddig, M.: Tensor series expansion of a spherical function for use in constitutive theory of materials containing orientable particles. Proc. Est. Acad. Sci. 67(1), 73–92 (2018). Open-Access CC-BY-NC 4.0
Eik, M., Puttonen, J., Herrmann, H.: The effect of approximation accuracy of the orientation distribution function on the elastic properties of short fibre reinforced composites. Compos. Struct. 148, 12–18 (2016)
Abràmoff, M.D., Magalhães, P.J., Ram, S.J.: Image processing with ImageJ. Biophotonics Int. 11(7), 36–42 (2004)
Herrmann, H.: Alignment tensor package for R (2016). http://bitbucket.org/vispar/alignment
R Development Core Team: R: A Language and Environment for Statistical Computing. R Foundation for Statistical Computing, Vienna, Austria (2011). ISBN 3-900051-07-0
Lemon, J.: Plotrix: a package in the red light district of R. R-News 6(4), 8–12 (2006)
Acknowledgements
The authors gratefully acknowledge the funding by the Estonian Research Council by the exploratory research grant PUT1146.
We also thank Maria Kremsreiter who helped during her Erasmus+ internship at the Institute of Cybernetics. Therefore: With the support of the Erasmus+ programme of the European Union.
Thanks to E-Betoonelement, especially Aare Lessuk, Rasmus-R. Marjapuu and Sergei Graf, for preparing the experiment plate.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer Nature Switzerland AG
About this chapter
Cite this chapter
Herrmann, H., Goidyk, O., Braunbrück, A. (2019). Influence of the Flow of Self-Compacting Steel Fiber Reinforced Concrete on the Fiber Orientations, a Report on Work in Progress. In: Herrmann, H., Schnell, J. (eds) Short Fibre Reinforced Cementitious Composites and Ceramics. Advanced Structured Materials, vol 95. Springer, Cham. https://doi.org/10.1007/978-3-030-00868-0_7
Download citation
DOI: https://doi.org/10.1007/978-3-030-00868-0_7
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-00867-3
Online ISBN: 978-3-030-00868-0
eBook Packages: Chemistry and Materials ScienceChemistry and Material Science (R0)