Abstract
The surface quality of a machined product is a very important consideration in determining process parameters. Due to the inherent nature of the machining process, there always exists a certain amount of residual stress in the material after machining. This paper presents the results of the surface interrogation of machined workpieces by using an x-ray diffraction technique. The machining tests were performed with 4140 hot rolled steel at two speeds. During the tests, tool wear and surface finish were measured and compared to the measured residual stresses. The results show that the x-ray diffraction technique provides valuable information regarding the machining process and if used as an in-process monitoring method could provide a sensing technique for intelligent processing of materials.
Keywords
These keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.
This is a preview of subscription content, log in via an institution.
Buying options
Tax calculation will be finalised at checkout
Purchases are for personal use only
Learn about institutional subscriptionsPreview
Unable to display preview. Download preview PDF.
References
J. Tlusty and G. C. Andres, A Critical Review of Sensors for Unmanned Machining, Annals of the CIRP, Vol 32/2, pp. 563–572, (1983).
N. Skalli and R. Geslot, Effect of Grinding Conditions on Fatigue Behavior of 42 CO 4 Grade Steel, Annals of the CIRP, 32/1, pp. 481, (1983).
H. K. Tonshoff and F. Hetz, Influence of Thermal and Mechanical Impacts on Fatigue in Precision Grinding, “Advances in Surface Treatments,” Pergamon Press, Oxford, (1984).
N. H. Polakowshi, Effect of Residual Stress on Yielding and Strain-Agening of Carbon Steel, J. Iron Steel Inst., pp. 369-376, (1952).
L. P. Tarasov, W. S. Hyler and H. R. Letner, Effect of Grinding Conditions and Resultant Residual Stresses on the Fatigue Strength of Hardened Steel, Proc. Am. Soc. Test. Mat. 57, pp. 601–622, (1957).
E. Brinksmeier et. al, Residual Stresses — Measurement and Causes in Machining Processes Annals of the CIRP, Vol. 31/2, pp. 491–510, (1982).
C. O. Ruud, D. J. Snoha, D. P. Ivkovich, and A. R. Mcllree, “Residual Stresses in Inconel 600 U-Bend Heat Exchanger Tubes,” J. of Press Vess. Tech. 112, pp 169–174, May (1990).
P. Leskovar and J. Peklenik, Influences Affecting Surface Integrity in the Cutting Process, Annals of the CIRP, Vol. 31/1, pp. 447–450, (1982).
E. Brinksmeier, X-ray Stress Measurement — A Tool for the Study and Layout of Machining Processes, Annals of the CIRP, Vol 34/1, pp. 485–490, (1985).
R. G. Treuting and W. T. Read, A Mechanical Determination of Biaxial Stress in Sheet Materials, J. Appl. Phys, 22, pp. 130–134, (1951).
C. O. Ruud, G. H. Pennington, E. M. Brauss and S. D. Weedman, “Simultaneous Residual Stress and Retained Austenite Measurement by X-Ray Diffraction,” Nondestructive Characterization of Materials III, pp. 406–412, Springer-Verlag, Berlin (1989).
M. Field, J. F. Kahles and J. T. Cammett, A Review of Measuring Methods for Surface Integrity, Annals of the CIRP, Vol. 21/2, pp. 219–238, (1972).
O. S. Es-said and J. G. Morris, A Method to Calculate the Resistivity of Strip Cast 300 Series Aluminum Alloys Based on their Nominal Solute Content, NDC of Mat. II, Plenum Press, pp. 271-280, (1987).
S. R. Buxbaumn and R. E. Green, Ultrasonic Characterization of Titanium 6211 Weld Materials, Nondestructive Methods for Mat. Prop. Pet., Plenum Pres, pp. 271-288, (1984).
F. Zankl, D. G. Barkow and A. O. Schmidt, X-Ray Diffraction as a Gage for Measuring Cold Work Produced in Milling, Trans. of ASME, pp. 307-318, (1947).
Y. Matsumoto, M. M. Barash and C. R. Liu, Residual Stress in the Machined Surface of Hardened Steel, ASME PED-Vol. 12. pp. 193-204, (1984).
H. K. Tonshoff and E. Brinksmeier, Optimization of Computer Controlled X-Ray Stress Analysis, Annals of the CIRP, 30, pp. 509–13, (1983).
C. O. Ruud, Position-Sensitive Detector Improves X-Ray Powder Diffraction, Ind. R&D, pp. 84-86, (1983).
SAE, Residual Stress Measurement by X-Ray Diffraction — SAE J784a, Soc. of Auto. Engr., 400 Commonwealth Dr., Warrendale, PA (1971).
C. O. Ruud, “Application of a Position Sensitive Sintilation Detector to Nondestructive X-Ray Diffraction Characterization of Metallic Components,” Nondest. Methods for Mat. Prop. Meas., Plenum Press, pp 21-38, (1984).
C. M. Brackman, “Residual Stresses in Cubic Materials with Orthorhombic or Monoclinic Specimen Symmetry: Influence of Texture on Psi Splitting and Non-linear Behavior,” J. APPI CVS., 16, 325–340, June (1983).
Author information
Authors and Affiliations
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 1991 Springer Science+Business Media New York
About this chapter
Cite this chapter
Shin, Y.C., Oh, S.J., Ruud, C.O. (1991). Interrogation of Residual Stresses of Machined Surface by an X-ray Diffraction Technique. In: Ruud, C.O., Bussière, J.F., Green, R.E. (eds) Nondestructive Characterization of Materials IV. Springer, Boston, MA. https://doi.org/10.1007/978-1-4899-0670-0_50
Download citation
DOI: https://doi.org/10.1007/978-1-4899-0670-0_50
Publisher Name: Springer, Boston, MA
Print ISBN: 978-1-4899-0672-4
Online ISBN: 978-1-4899-0670-0
eBook Packages: Springer Book Archive