Abstract
The potential of cutting heads of various types in cutting cylindrical gears is analyzed. On that basis, the following gear-cutting systems are proposed: a progressive high-speed system; a compact low-waste system; and a system with matched cutting of gears in transmissions.
Similar content being viewed by others
REFERENCES
Fedorov, Yu.N., Artamonov, V.D., and Zolotukhina, O.L., Machining cylindrical gears by means of cutting heads, Russ. Eng. Res., 2007, vol. 27, no. 11, pp. 810–811.
Fedorov, Yu.N., Artamonov, V.D., and Zolotukhina, O.L., Tooth rolling of cylindrical gears, Stanki Instrum., 2005, no. 5, pp. 24–26.
Fedorov, Yu.N., Artamonov, V.D., and Zolotukhina, O.L., Paired tooth cutting of cylindrical gears, Russ. Eng. Res., 2009, vol. 29, no. 3, pp. 319–321.
Gryazev, M.V., Fedorov, Yu.N., Artamonov, V.D., and Zolotukhina, O.L., Manufacture of cylindrical gears from progressive blanks with a stamped tooth crown, Russ. Eng. Res., 2010, vol. 30, no. 7, pp. 749–750.
Gryazev, M.V., Fedorov, Yu.N., Artamonov, V.D., and Zolotukhina, O.L., Optimal machining of teeth in stamped tooth crowns by cutter heads, Russ. Eng. Res., 2010, vol. 30, no. 8, pp. 827–829.
Malikov, A.A., Sidorkin, A.V., and Yamnikov, A.S., Cutting and plastic deformation in the shaving and rolling of cylindrical gears with round teeth, Russ. Eng. Res., 2013, vol. 33, no. 6, pp. 363–366.
Malikov, A.A. and Sidorkin, A.V., Heat liberation in the shaving of cylindrical gears, Russ. Eng. Res., 2015, vol. 35, no. 8, pp. 631–634.
Malikov, A.A., Yamnikov, A.S., Fedorov, Yu.N., and Zolotukhina, O.L., Simplified calculation of the initial rack profile in tooth-shaping mills, Russ. Eng. Res., 2008, vol. 28, no. 10, pp. 1015–1017.
Malikov, A.A., Fedorov, Yu.N., Artamonov, V.D., and Zolotukhina, O.L., RF Patent 2502585, Byull. Izobret., 2013, no. 36.
Fedorov, Yu.N., Artamonov, V.D., and Zolotukhina, O.L., RF Patent 2347650, Byull. Izobret., 2009, no. 6.
Fedorov, Yu.N., Artamonov, V.D., and Zolotukhina, O.L., Paired cutting of cylindrical gears with longitudinally modified teeth, Russ. Eng. Res., 2009, vol. 29, no. 6, pp. 625–627.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
The authors declare that they have no conflicts of interest.
Additional information
Translated by B. Gilbert
About this article
Cite this article
Artamonov, V.D. Production of Cylindrical Gears by Means of Cutting Heads. Russ. Engin. Res. 39, 970–972 (2019). https://doi.org/10.3103/S1068798X19110030
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X19110030