Abstract
The upsetting of a composite cylinder in frictionless creep is analyzed in energy terms. Three loading programs that lead to upsetting of the cylinder by the same amount in the same time are compared. Variational analysis indicates that the kinematic loading program is best for industrial use.
Similar content being viewed by others
REFERENCES
Tarnovskii, I.Ya., Levanov, A.N., and Poksevatkin, M.I., Kontaktnye napryazheniya pri plasticheskoi deformatsii (Contact Stresses in Plastic Deformation), Moscow: Metallurgiya, 1966.
Sivak, I.O., Ogorodnikov, V.A., Pekhov, G.F., and Syrnev, B.V., Calculation of the limiting shaping of blanks from a hardly-deforming alloy with axisymmetric upsetting, Kuznechno-Shtampovochnoe Proizvod., 1980, no. 2, pp. 2–5.
Burov, Yu.G., Calculation of metal temperature of a billet during hot upsetting, Kuznechno-Shtampovochnoe Proizvod., 1984, no. 11, p. 14.
Archakov, A.T. and Nekrasov, V.A., Experimental analysis of torsional upsetting, Kuznechno-Shtampovochnoe Proizvod.–Obrab. Mater. Davleniem, 2003, no. 3, pp. 21–26.
Antoshchenkov, Yu.M. and Taupek, I.M., Specific modeling of axisymmetric upsetting, Kuznechno-Shtampovochnoe Proizvod.–Obrab. Mater. Davleniem, 2014, no. 10, pp. 42–49.
Lin, Z.C. and Lin, Z.C., An investigation of a coupled analysis of a thermo-elastic-plastic model during warm upsetting, Int. J. Mach. Tools Manuf., 1990, vol. 30, no. 4, pp. 599–612.
Lin, S.Y., Investigation of the effect of dissimilar interface frictional properties on the process of hollow cylinder upsetting, J. Mater. Process. Technol., 1997, vol. 66, nos. 1–3, pp. 204–215.
Thiebaut, C., Bonnet, C., and Morey, J.M., Evolution of the friction factor of a molybdenum work piece during upsetting tests at different temperatures, J. Mater. Process. Technol., 1998, vol. 77, nos. 1–3, pp. 240–245.
Lin, S.Y. and Lin, F.C., Influences of the geometrical conditions of die and workpiece on the barreling formation during forging–extrusion process, J. Mater. Process. Technol., 2003, vol. 140, pp. 54–58.
Malinin, N.N., Polzuchest’ v obrabotke metallov (Creep of Metals during Processing), Moscow: Mashinostroenie, 1986.
Lokoshchenko, A.M., Creep and Long-Term Strength of Metals, Boca Raton, Fl: CRC Press, 2017.
Lokoshchenko, A.M., Optimal mode for upsetting of cylinders with friction, Vestn. Mashinostr., 2016, no. 9, pp. 44–48.
Malinin, N.N., Prikladnaya teoriya plastichnosti i polzuchesti (Applied Theory of Plasticity and Creep), Moscow: Mashinostroenie, 1975.
Krotov, V.F. and Brovman, M.Ya., Extreme processes of plastic deformation of metals, Izv. Akad. Nauk SSSR, Otd. Tekh. Nauk, Mekh. Mashinostr., 1962, no. 3, pp. 148–153.
Krasnov, M.L., Makarenko, G.I., and Kiselev, A.I., Variatsionnoe ischislenie, zadachi i uprazhneniya (Calculus of Variation, Tasks, and Exercises), Moscow: Nauka, 1973.
ACKNOWLEDGMENTS
Financial partial support was provided by the Russian Foundation for Basic Research (project 17-08-00210).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated by Bernard Gilbert
About this article
Cite this article
Lokoshchenko, A.M. Optimal Upsetting of Composite Cylinders. Russ. Engin. Res. 39, 189–194 (2019). https://doi.org/10.3103/S1068798X1903016X
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X1903016X