Abstract—The influence of the surface roughness on the fatigue strength of threaded joints is considered. Multifactorial experiment design is used to analyze the influence of the geometry in tap sharpening and the thickness of the cut layer on the roughness of the machined surface. A durable new tap design ensures high quality of the machined surface.
Similar content being viewed by others
REFERENCES
Matalin, A.A., Tekhnologiya mekhanicheskoi obrabotki (Mechanical Machining), Moscow: Mashinostroenie, 1977.
Yakushev, A.I., Mustaev, R.Kh., and Mavlyutov, R.R., Povyshenie prochnosti i nadezhnosti rez’bovykh soedinenii (Improvement of Strength and Reliability of Threaded Joints), Moscow: Mashinostroenie, 1979.
Reshetov, D.N., Detali mashin (Machine Parts), Moscow: Mashinostroenie, 1974.
Guseinov, A.G., Precision threading, Vestn. Mashinostr., 2004, no. 10, pp. 47–48.
Keksin, A.I., The quality of internal threaded surfaces based on preliminary magnetic-abrasive polishing of a complex profile tool, Extended Abstract of Cand. Sci. (Eng.) Dissertation, St. Petersburg: St. Petersb. Min. Univ., 2017.
Guseinov, R.V., Research, optimization, and scientific substantiation of dynamic processing of internal surfaces in refractory materials, Extended Abstract of Doctoral (Eng.) Dissertation, St. Petersburg: State Mar. Tech. Univ., 1998.
Guseinov, R.V., Vibration during machining of holes, Metalloobrabotka, 2017, no. 4, pp. 23–28.
Guseinov, R.V. and Rustamova, M.R., Internal thread cutting in the presence of radial forces, Russ. Eng. Res., 2009, vol. 29, no. 5, pp. 480–481.
Guseinov, R.V. and Rustamova, M.R., Improving the machining of small holes, Russ. Eng. Res., 2013, vol. 33, no. 1, pp. 29–31.
Zhang, J.Y. and Liang, S.Y., Process optimization of finish turning of hardened steels, Mater. Manuf. Process., 2007, vol. 22, no. 1, pp. 107–113.
El-Axir, M.H. and Elkhabeery, M.M., Modeling and parameter optimization for surface roughness and residual stress in dry turning process, Eng., Technol. Appl. Sci. Res., 2017, vol. 7, no. 5, pp. 2047–2055.
Ivanina, I.V., The effect of the plane angle on torque during formation of threads according to the generator cutting scheme, Mashinostroenie: Setevoi Elektron. Nauchn. Zh., 2015, vol. 3, no. 4, pp. 27–30.
Novik, F.S. and Arsov, Ya.B., Optimizatsiya protsessov tekhnologii metallov metodami planirovaniya eksperimentov (Optimization of Metal Technology Processes by the Method of Experiment Planning), Moscow: Mashinostroenie, 1980.
Guseinov, R.V., Mathematical modeling of the cutting process of corrosion-resistant steels, Vestn. Astrakh. Gos. Tekh. Univ., Ser.: Morsk. Tekhn. Tekhnol., 2015, no. 4, pp. 65–70.
Guseinov, R.V., RF Patent 2229965, 2004.
Akhmedova, M.R. and Guseinov, R.V., High-performance taps for cutting threads in refractory materials, Vestn. Dagest. Gos. Tekh. Univ., Tekh. Nauki, 2016, no. 4, pp. 8–16.
Yamnikov, A.S., Maslennikov, V.A., and Tatarinov, V.N., Influence of geometry of axial tool on the minimum thickness of cutting layer, Izv. Tul. Gos. Univ., Tekh. Nauki, 2017, no. 8-2, pp. 95–103.
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated by Bernard Gilbert
About this article
Cite this article
Guseinov, R.V., Akhmedova, M.R. Improving the Performance of Threaded Joints. Russ. Engin. Res. 39, 229–233 (2019). https://doi.org/10.3103/S1068798X19030109
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X19030109