Skip to main content
SpringerLink
Log in

Roughness of Cylindrical Parts in Transverse Burnishing by Flat Plates

  • Published:
Russian Engineering Research Aims and scope

Abstract

The use of transverse burnishing by means of flat plates for combined finishing and strengthening of cylindrical parts is considered. The influence of the compressive strain and the total number of workpiece rotations on the surface roughness is determined experimentally.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
Fig. 5.
Fig. 6.
Fig. 7.
Fig. 8.
Fig. 9.

Similar content being viewed by others

REFERENCES

  1. Dudnikov, I.A., Classification of the parts for quality control of their surface layer, Vost.-Evrop. Zh. Peredovykh Tekhnol., 2011, vol. 5, no. 7, pp. 10–13.

    Google Scholar 

  2. Dudnikov, A.A., Belovod, A.I., and Kelemesh, A.A., Quality of surface layer of the part during surface plastic deformation, Tekhnol. Audit Rezervy Proizvod., 2012, no. 1, pp. 22–25.

  3. Odintsov, L.G. and Pleshakov, V.V., Quality of surface and operational properties of machine parts by diamond smoothing, Naukoemkie Tekhnol. Mashinostr., 2013, no. 1, pp. 41–48.

  4. Shneider, Yu.G., Ekspluatatsionnye svoistva detalei s regulyarnym mikrorel’efom (Operational Properties of the Parts with Regular Microrelief), Leningrad: Mashinostroenie, 1982.

  5. Ezhelev, A.V., Bobrovskii, I.N., and Luk’yanov, A.A., Analysis of treatment method of surface plastic deformation, Fundam. Issled., 2012, no. 6-3, pp. 642–646.

  6. Smelyanskii, V.M., Mekhanika uprochneniya detalei poverkhnostnym plasticheskim deformirovaniem (Mechanics of Strengthening of the Parts by surface Plastic Deformation), Moscow: Mashinostroenie, 2002.

  7. Otenii, Ya.N., Tekhnologicheskoe obespechenie kachestva detalei mashin poverkhnostnym plasticheskim deformirovaniem: monografiya (Quality Ensure of Machine Parts by Surface Plastic Deformation: Monograph), Volgograd: Politekhnik, 2005.

  8. Fam, D.F., Zaides, S.A., and Nguen, V.Kh., The conditions of cross-rolling during surface plastic deformation, Vestn. Irkutsk. Gos. Tekh. Univ., 2015, no. 4, pp. 48–52.

  9. Kurguzov, S.A., Krasnoperov, D.N., Krasnoperova, I.A., et al., Analysis of technology forming on the surface microrelief tribounit, Tr. Sworld, 2014, vol. 6, no. 4, pp. 45–49.

    Google Scholar 

  10. Leonov, O.A. and Vergazova, Yu.G., Relative support length of surface profile and Longevity of the parts, Innovatsionnaya Nauka, 2016, no. 1–2 (13), pp. 81–83.

Download references

Author information

Authors and Affiliations

  1. Irkutsk National Research Technical University, Irkutsk, Russia

    S. A. Zaides &  Fam Dak Fong

Authors
  1. S. A. Zaides
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Fam Dak Fong
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to S. A. Zaides.

Additional information

Translated by Bernard Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Zaides, S.A., Fam Dak Fong Roughness of Cylindrical Parts in Transverse Burnishing by Flat Plates. Russ. Engin. Res. 38, 921–925 (2018). https://doi.org/10.3103/S1068798X18120420

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X18120420

Keywords:

Search

Navigation