Skip to main content
SpringerLink
Log in

Temperature Rise in the Cutting Zone during the High-Speed Milling of Heat-Resistant Alloys

  • Published:
Russian Engineering Research Aims and scope

Abstract

The temperature rise in the cutting zone during high-speed milling is considered. A method of calculating this temperature rise is proposed.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.

Similar content being viewed by others

REFERENCES

  1. Albagachiev, A.Yu., Preobrazhenskaya, E.V., and Krasko, A.S., A model of high-speed cutting of KhN77TYuR steel, Materialy mezhdunarodnoi nauchno-tekhnicheskoi konferentsii “Informatika i tekhnologii. Innovatsionnye tekhnologii v promyshlennosti i informatike” (Proc. Int. Sci.-Tech. Conf. “Informatics and Technologies. Advanced Technologies in Industry and Informatics”), Bulatov, M.F., Ed., Moscow: Mosk. Tekhnol. Univ., Fiz.-Tekhnol. Inst., 2017, no. 23, pp. 188–190.

  2. Lut’yanov, A.V. and Stramtsova, E.S., Optimal temperature in milling of monowheel of the AI-222-25 turbojet engine, Evolutio. Tekh. Nauki, 2017, no. 8, pp. 49–51.

  3. Albagachiev, A.Yu., Preobrazhenskaya, E.V., and Krasko, A.S., A model of high-speed cutting of KhN77TYuR steel, Materialy mezhdunarodnoi nauchno-tekhnicheskoi konferentsii “Informatika i tekhnologii. Innovatsionnye tekhnologii v promyshlennosti i informatike” (Proc. Int. Sci.-Tech. Conf. “Informatics and Technologies. Advanced Technologies in Industry and Informatics”), Bulatov, M.F., Ed., Moscow: Mosk. Tekhnol. Univ., Fiz.-Tekhnol. Inst., 2017, no. 23, pp. 188–190.

  4. Esov, V.B., Klimochkin, K.O., Khanov, A.M., and Khurmatullin, O.G., The application of ionized air cooling technology in high-speed milling, Vestn. Permsk. Nats. Issled. Politekh. Univ., 2011, vol. 13, no. 4, pp. 103–105.

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Moscow Technological University, Institute of Mechanical Engineering, Russian Academy of Sciences, Moscow, Russia

    A. Yu. Albagachiev

  2. Moscow Technological University, Moscow, Russia

    E. V. Preobrazhenskaya, A. S. Krasko & E. S. Stramtsova

Authors
  1. A. Yu. Albagachiev
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. E. V. Preobrazhenskaya
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. S. Krasko
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. E. S. Stramtsova
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to A. Yu. Albagachiev.

Additional information

Translated by Bernard Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Albagachiev, A.Y., Preobrazhenskaya, E.V., Krasko, A.S. et al. Temperature Rise in the Cutting Zone during the High-Speed Milling of Heat-Resistant Alloys. Russ. Engin. Res. 38, 1009–1011 (2018). https://doi.org/10.3103/S1068798X18120031

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X18120031

Keywords:

Search

Navigation