Advertisement

Russian Engineering Research

, Volume 38, Issue 12, pp 1038–1041 | Cite as

Laser Machining of Tool Steels

  • V. V. ZvezdinEmail author
  • R. M. KhisamutdinovEmail author
  • V. A. GrechishnikovEmail author
  • R. R. SaubanovEmail author
  • I. Kh. IsrafilovEmail author
  • S. M. PortnovEmail author
  • S. Yu. YurasovEmail author
Article
  • 6 Downloads

Abstract

Laser quenching and application of wear-resistant powder to the cutting edge of a hob is considered, with careful positioning of the laser spot. Experimental data are analyzed. The quality of quenching and powder surfacing depends on the machining conditions; the quality of the laser radiation; the energy characteristics of the laser system; and the precision in positioning the laser focus.

Keywords:

laser quenching laser surfacing laser quality surfacing parameters thermal-influence zone laser spot positional precision 

Notes

REFERENCES

  1. 1.
    Zvezdin, V.V., Pesoshin, V.A., Saubanov, R.R., and Rakhimov, R.R., Control of a laser technological complex of tool hardening, Vestn. Chuvash. Gos. Univ., 2016, no. 3, pp. 188–193.Google Scholar
  2. 2.
    Zvezdin, V.V., Khisamutdinov, R.M., Israfilov, I.Kh., and Rakhimov, R.R., Control of the position of the laser radiation focus during the welding of the teeth of the cutter, Materialy mezhdunarodnoi nauchno-tekhnicheskoi konferentsii “Innovatsionnye mashinostroitel’nye tekhnologii, oborudovanie i materialy” (Proc. Int. Sci.-Tech. Conf. “Innovative Machine Engineering Technologies, Equipment, and Materials”), Kazan, 2016, pp. 72–76.Google Scholar
  3. 3.
    Chernova, M.A., Khisamutdinov, R.M., Zvezdin, V.V., et al., Metallographic studies of laser deposition of wear-resistant powders on the tool, Fundam. Issled., 2015, no. 114, pp. 753–758.Google Scholar
  4. 4.
    Zvezdin, V.V., Samorsky, V.V., Pesoshin, V.A., et al., Improvement of combined laser-plasma welding, Izv. Vyssh. Uchebn. Zaved., Fiz.,2015, vol. 58, no. 9–2, pp. 36–39.Google Scholar
  5. 5.
    Khisamutdinov, R.M., Zvezdin, V.V., and Khisamutdinov, M.R., Laser surfacing of special powders to increase the wear resistance of the teeth of cutter, Mezhdunar. Zh. Prikl. Fundam. Issled., 2017, no. 4–3, pp. 482–485.Google Scholar
  6. 6.
    Zvezdin, V.V., Israfilov, D.I., Portnov, S.M., et al., Automatic control system of high-precision welding of preparations by the laser radiation at influence of the plasma torch, Izv. Vyssh. Uchebn. Zaved., Fiz., 2015, vol. 58, no. 9-3, pp. 51–54.Google Scholar
  7. 7.
    Tekhnologicheskie lazery. Tom 1. Raschet, proektirovanie i ekspluatatsiya (Technological Lasers, Vol. 1: Calculation, Design, and Exploitation), Abil’siitov, G.A., Ed., Moscow: Mashinostroenie, 1991.Google Scholar
  8. 8.
    Zvezdin, V.V., Khamadeev, A.V., Fardiev, R.K., et al., Effect of mode composition of laser radiation on the heat-affected zone in metals, Vestn. Kazan. Gos. Tekh. Univ. im. A.A. Tupoleva, 2007, no. 2, pp. 84–85.Google Scholar
  9. 9.
    Grechishnikov, V.A., Sedov, B.E., and Romanov, V.B., Proektirovanie diskovoi frezy dlya obrabotki vintovoi kanavki sverla. Metodicheskie ukazaniya dlya vypolneniya kursovoi raboty (Design of a Milling Cutter for Treatment of Helical Groove of a Drill: Methodological Recommendations for the Course Graduate Work), Moscow: Mosk. Gos. Tekhnol. Univ., Stankin, 2007.Google Scholar

Copyright information

© Allerton Press, Inc. 2018

Authors and Affiliations

  1. 1.Naberezhnye Chelny Institute, Kazan Federal UniversityKazanRussia
  2. 2.Stankin Moscow State Technical UniversityMoscowRussia

Personalised recommendations