The influence of percentage of bars lapped on performance of splices
- 280 Downloads
Most design codes encourage the staggering of lapped splices in a section, such that a portion of the bars in the cross section remains continuous throughout the lap zone. A penalty on lap length may be imposed if all bars are lapped at one section. In the literature, however, almost all tested specimens have had all reinforcement lapped at the same section. This paper presents results of tests carried out to shed some new light on the behaviour of lap splices where only a portion of bars is lapped. To this end, four point bending tests were carried out on 24 full-scale beams with all or part of the longitudinal reinforcement lap spliced at mid-span. The beams were reinforced with either 16 or 20 mm diameter rebars, included two grades of concrete and various lap splices configurations, all confined by links. All the beams were designed with the same concrete cover and with the minimum amount of transverse reinforcement permitted by MC2010, equal to 50 % of the area of the lapped bars. The resistance and the residual strength of the splices were measured and compared with the results of specimens with continuous bars and with all bars lapped. The results show that lapping only a portion of bars at a section impairs splice strength, although some post-peak strength is maintained by the continuous bars. These outcomes raise questions over the validity of EC2 and ACI 318-11 provisions which allow a reduction in lap-length when splices are staggered.
KeywordsConcrete Reinforcement Bond Lap splices Splitting Tests fib-Model Code 2010
The Authors are grateful to engineers R. A. Kirk, R. Stretti, S. Bolzacchini, A. Sfreddo and M. Zanoni for their assistance in carrying out the tests within their thesis work. The know-how and expertness of the technicians of the Laboratory P. Pisa of the University of Brescia are also gratefully acknowledged. The support Alfacciai Group, who provided the steel bars, is gratefully acknowledged as is the expertise of eng. A. Milini of Scuola Edile Bresciana, who manufactured the beams.
- 1.Metelli G, Cairns J, Plizzari G (2010) Influence of bar continuity on behaviour of lapped splices. In: Proceedings of the 2010 fib congress and PCI convention bridge conference, Washington, June 2010, pp 2904–2915Google Scholar
- 3.ACI Committee 318 (2011) building code requirements for structural concrete (ACI 318-11) and commentary, American Concrete Institute, Farmington Hills, Mich., pp 505Google Scholar
- 4.Darwin D (2005) Tension development length and lap splice for reinforced concrete members. Program Struct Eng Mater 7(210):225Google Scholar
- 5.ENV 1992-1-1:2004, Eurocode 2: design of concrete structures—part 1-1: general rules, and rules for buildings, European Committee for StandardizationGoogle Scholar
- 6.Comité Euro-International du béton (1993) CEB-FIP model code 1990-design code. Thomas Telford, London, p 437, ISBN 0 7277 1696 4Google Scholar
- 7.Magnusson J (2000) Bond and anchorage of ribbed bars in high-strength concrete. PhD thesis, Chalmers University, Göteborg, Sweden, pp 234Google Scholar
- 9.fib—International Federation for Structural Concrete (2013) Model Code for concrete structures 2010. Ernst & Sohn, Berlin, Germany, pp 434, ISBN 978-3-433-03061-5Google Scholar
- 12.Tepfers R (1973) A theory of bond applied to overlapped tensile reinforcement splices for deformed bars. Chalmers University of Technology, Goteborg, Publ. 73/2, p 328Google Scholar
- 16.EN 10080:2005. Steel for reinforcement of concrete—weldable reinforcing steel—general. European Committee for StandardizationGoogle Scholar
- 17.EN 12350-2:2001. Testing fresh concrete—slump test. European Committee for StandardizationGoogle Scholar
- 18.EN 15630-1:2010. Steel for the reinforcement and prestressing of concrete. Test methods-part 1: reinforcing bars, wire rod and wire. European Committee for StandardizationGoogle Scholar