Abstract
A plain carbon steel was overlayed with a wear-resistant hardfacing alloy by manual arc welding. Low stress abrasive wear tests were conducted with an ASTM rubber wheel abrasion tester using crushed silica and as the abrasive medium. The wear rate decreased with sliding distance, and there was an overall improvement in the abrasive wear resistance as a result of overlaying. The wear behavior of the samples has been discussed in terms of microstructural features while the examination of wear surface and subsurface regions provides insight into the wear mechanisms.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
W. Wu and L.T. Wu,Metall. Mater. Trans. A, Vol 27, 1996, p 3639
C. Nusum,Proc. Conf. Therm. Spray Technol.—New Ideas and Processes, American Society for Metals, 1982, p 85
R.F. Bunshah,Deposition Technol. for Films and Coatings, R.F. Bunshah, Ed., Noyes Publications, 1982, p 85
M. Bambergere, M. Boas, and O. Akin,Z. Metallkd., Vol 79, 1988, p 806
Metals Handbook, 8th ed., Vol 3 and 4, American Society for Metals, 1972
H.N. Farmer, Symposium on Materials for Mining Industry (Vail, CO), Sept 1974
R. Dasgupta, B.K. Prasad, A.K. Jha, O.P. Modi, S. Das, and A.H. Yegneswaran,Surf. Eng., Vol 13 (No. 2), 1997, p 123
R.E. Brown,Met. Prog., Vol 28, 1985, p 136
A.G. Foley, C.J. Chisholm, and V.A. Melees,Tribol. Int., Vol 21, 1988, p 97
“Standard Practice for Conducting Dry Sand Rubber Wheel Abrasion Tests”, G 65-81,Annual Book of ASTM Standards, ASTM, 1981
B. Bhushan and B.K. Gupta,Handbook of Tribology, McGrawHill, Inc., 1991, p 81
Metals Handbook, 8th ed., Vol 7, American Society for Metals, 1972, p 99
R. Dasgupta, B.K. Prasad, A.K. Jha, O.P. Modi, S. Das, and A.H. Yegneswaran,Wear, Vol 209, 1997, p 255
M.A. Moore,Wear, Vol 28, 1974, p 59
K. Hokkirigawa and K. Kato,Wear, Vol 123, 1988, p 241
M. Askoy, M.B. Karamis, and E. Evin,Wear, Vol 193, 1996, p 248
L. Fang and Q.D. Zhou,Wear, Vol 151, 1991, p 313
O. Vingsbo and S. Hogmark, Wear in Steels,Fundamentals of Friction and Wear in Materials, D.A. Rigney, Ed., American Society for Metals, 1981, p 373
A.G. Atkins,Int. J. Prod. Res., Vol 12, 1974, p 263
B.K. Prasad and S.V. Prasad,Wear, Vol 151, 1991, p 1
O.P. Modi, B.K. Prasad, S. Das, A.K. Jha, and A.H. Yegneswaran,Mater. Trans. JIM, Vol 35, 1994, p 67
S. Das, B.K. Prasad, A.K. Jha, O.P. Modi, and A.H. Yegneswaran,Wear, Vol 162–164, 1993, p 802
D.A. Rigney and J.P. Hirth,Wear, Vol 53, p 345
O. Scheffler and C. Allen,Tribol. Int., Vol 21, 1988, p 127
K.M. Mashloosh,Tribol. Int., Vol 18, p 259
M.A. Verspivi, G. de With, P.G. Th. Van der Varst, and M. Buys,Wear, Vol 188, 1995, p 102
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Dasgupta, R., Prasad, B.K., Jha, A.K. et al. Low stress abrasive wear behavior of a hardfaced steel. J. of Materi Eng and Perform 7, 221–226 (1998). https://doi.org/10.1361/105994998770347954
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1361/105994998770347954