Clays and Clay Minerals

, Volume 66, Issue 3, pp 209–219 | Cite as

Nanoscale Elastic Properties of Dry and wet Smectite

  • Junfang ZhangEmail author
  • Marina Pervukhina
  • Michael B. Clennell


The nanoscale elastic properties of moist clay minerals are not sufficiently understood. The aim of the present study was to understand the fundamental mechanism for the effects of water and pore size on clay mineral (K+-smectite) elastic properties using the General Utility Lattice Program (GULP) with the minimum energy configurations obtained from molecular dynamics (MD) simulations. The simulation results were compared to an ideal configuration with transversely isotropic symmetry and were found to be reasonably close. The pressures computed from the MD simulations indicated that the changes due to water in comparison to the dry state varied with the water content and pore size. For pore sizes of around 0.8–1.0 nm, the system goes through a process where the normal pressure is decreased and reaches a minimum as the water content is increased. The minimum normal pressure occurs at water contents of 8 wt.% and 15 wt.% for pore sizes of around 0.8 nm and 1 nm, respectively. Further analyses of the interaction energies between water and K+-smectite and between water and water revealed that the minimum normal pressure corresponded to the maximum rate of slope change of the interaction energies (the second derivative of the interaction energies with respect to the water content). The results indicated that in the presence of water the in-plane stiffness parameters were more correlated to the pressure change that resulted from the interplay between the interactions of water with K+-smectite and the interactions of water with water rather than the water content. The in-plane stiffness parameters were much higher than the out-of-plane parameters. Elastic wave velocities for the P and S waves (VP and VS) in the dry K+-smectite with a pore size of ~1 nm were calculated to be 7.5 and 4.1 km/s, respectively. The P and S wave velocity ratio is key in the interpretation of seismic behavior and revealed that VP/VS = 1.64–1.83, which were values in favorable agreement with the experimental data. The results might offer insight into seismic research to predict the mechanical properties of minerals that are difficult to obtain experimentally and can provide complimentary information to interpret seismic surveys that can assist gas and oil exploration.

Key Words

Elastic Properties Molecular Dynamics Simulation Normal Pressure P-wave and S-wave Velocities Smectite 


Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.


  1. Bailey, S.W. (1980) Structures of layer silicates, Chapter 1, p. 5 in: Crystal Structures of Clay Minerals and Their X-ray Identification (G.W. Brindley and G. Brown, editors). Mineralogical Society, London.Google Scholar
  2. Bayuk, I.O., Ammerman, M., and Chesnokov, E.M. (2007) Elastic moduli of anisotropic clay. Geophysics, 72, D107–D117.CrossRefGoogle Scholar
  3. Benazzouz, B.K. and Zaoui, A. (2012) A nanoscale simulation study of the elastic behaviour in kaolinite clay under pressure. Materials Chemistry and Physics, 132, 880–888.CrossRefGoogle Scholar
  4. Berendsen, H.J.C., Grigera, J.R., and Straatsma, T.P. (1987) The missing term in effective pair potentials. Journal of Physical Chemistry, 91, 6269–6271.CrossRefGoogle Scholar
  5. Berendsen, H.J.C., Postma, J.P.M., Vangunsteren, W.F., Dinola, A., and Haak, J.R. (1984) Molecular-dynamics with coupling to an external bath. Journal of Chemical Physics, 81, 3684–3690.CrossRefGoogle Scholar
  6. Boek, E.S., Coveney, P.V., and Skipper, N.T. (1995) Monte Carlo molecular modeling studies of hydrated Li-, Na-, and K-smectites: Understanding the role of potassium as a clay swelling inhibitor. Journal of the American Chemical Society, 117, 12608–12617.CrossRefGoogle Scholar
  7. Brindley, G.W. (1980) Order-disorder in clay mineral structures, Chapter 2, p. 170 in: Crystal Structures of Clay Minerals and Their X-ray Identification (G.W. Brindley and G. Brown, editors). Mineralogical Society, London.Google Scholar
  8. Carcione, J.M. (2000) A model for seismic velocity and attenuation in petroleum source rocks. Geophysics, 65, 1080–1092.CrossRefGoogle Scholar
  9. Carpenter, B.M., Kitajima, H., Sutherland, R., Townend, J., Toy, V.G., and Saffer, D.M. (2014) Hydraulic and acoustic properties of the active Alpine Fault, New Zealand: Laboratory measurements on DFDP-1 drill core. Earth and Planetary Science Letters, 390, 45–51.CrossRefGoogle Scholar
  10. Carrier, B., Vandamme, M., Pellenq, R.J.M., and Van Damme, H. (2014) Elastic properties of swelling clay particles at finite temperature upon hydration. Journal of Physical Chemistry C, 118, 8933–8943.CrossRefGoogle Scholar
  11. Chalmers, G.R.L. and Bustin, R.M. (2008) Lower Cretaceous gas shales in northeastern British Columbia, Part I: Geological controls on methane sorption capacity. Bulletin of Canadian Petroleum Geology, 56, 1–21.CrossRefGoogle Scholar
  12. Chen, G., Zhang, J., Lu, S., Pervukhina, M., Liu, K., Xue, Q., Tian, H., Tian, S., Li, J., Clennell, M.B., and Dewhurst, D.N. (2016) Adsorption behavior of hydrocarbon on illite. Energy & Fuels, 30, 9114–9121.CrossRefGoogle Scholar
  13. Chesnokov, E.M., Tiwary, D.K., Bayuk, I.O., Sparkman, M.A., and Brown, R.L. (2009) Mathematical modelling of anisotropy of illite-rich shale. Geophysical Journal International, 178, 1625–1648.CrossRefGoogle Scholar
  14. Cook, J.E., Goodwin, L.B., Boutt, D.F., and Tobin, H.J. (2015) The effect of systematic diagenetic changes on the mechanical behavior of a quartz-cemented sandstone. Geophysics, 80, D145–D160.CrossRefGoogle Scholar
  15. Cygan, R.T., Liang, J.J., and Kalinichev, A.G. (2004) Molecular models of hydroxide, oxyhydroxide, and clay phases and the development of a general force field. Journal of Physical Chemistry B, 108, 1255–1266.CrossRefGoogle Scholar
  16. Ebrahimi, D., Pellenq, R.J.M., and Whittle, A.J. (2012) Nanoscale elastic properties of montmorillonite upon water adsorption. Langmuir, 28, 16855–16863.CrossRefGoogle Scholar
  17. Ebrahimi, D., Whittle, A.J., and Pellenq, R.J.M. (2016) Effect of polydispersity of clay platelets on the aggregation and mechanical properties of clay at the mesoscale. Clays and Clay Minerals, 64, 425–437.CrossRefGoogle Scholar
  18. El Husseiny, A. and Vanorio, T. (2015) The effect of micrite content on the acoustic velocity of carbonate rocks. Geophysics, 80, L45–L55.CrossRefGoogle Scholar
  19. Escamilla-Roa, E., Nieto, F., and Sainz-Diaz, C.I. (2016) Stability of the hydronium cation in the structure of illite. Clays and Clay Minerals, 64, 413–424.CrossRefGoogle Scholar
  20. Essmann, U., Perera, L., Berkowitz, M. L., Darden, T., Lee, H., and Pedersen, L. G. (1995) A smooth particle mesh Ewald method. Journal of Chemical Physics,.103, 8577–8593.CrossRefGoogle Scholar
  21. Ferrage, E. (2016) Investigation of the interlayer organization of water and ions in smectite from the combined use of diffraction experiments and molecular simulations. A review of methodology, applications, and perspectives. Clays and Clay Minerals, 64, 348–373.CrossRefGoogle Scholar
  22. Gale, J.D. (1997) Gulp: A computer program for the symmetryadapted simulation of solids. Journal of the Chemical Society-Faraday Transactions, 93, 629–637.CrossRefGoogle Scholar
  23. Gualtieri, A.F., Ferrari, S., Leoni, M., Grathoff, G., Hugo, R., Shatnawi, M., Paglia, G., and Billinge, S. (2008) Structural characterization of the clay mineral illite-1M. Journal of Applied Crystallography, 41, 402–415.CrossRefGoogle Scholar
  24. Hantal, G., Brochard, L., Laubie, H., Ebrahimi, D., Pellenq, R.J.M., Ulm, F.J., and Coasne, B. (2014) Atomic-scale modelling of elastic and failure properties of clays. Molecular Physics, 112, 1294–1305.CrossRefGoogle Scholar
  25. Horn, R.G. (1990) Surface forces and their action in ceramic materials. Journal of the American Ceramic Society, 73, 1117–1135.CrossRefGoogle Scholar
  26. Hornby, B.E., Schwartz, L.M., and Hudson, J.A. (1994) Anisotropic effective-medium modeling of the elastic properties of shales. Geophysics, 59, 1570–1583.CrossRefGoogle Scholar
  27. Hulan, T., Kaljuvee, T., Stubna, I., and Trnik, A. (2016) Investigation of elastic and inelastic properties of Estonian clay from a locality in Kunda during thermal treatment. Journal of Thermal Analysis and Calorimetry, 124, 1153–1159.CrossRefGoogle Scholar
  28. Hulan, T., Trnik, A., Stubna, I., Bacik, P., Kaljuvee, T., and Vozar, L. (2015) Development of Young’s modulus of illitic clay during heating up to 1100 degrees C. Materials Science-Medziagotyra, 21, 429–434.Google Scholar
  29. Jankula, M., Hulan, T., Stubna, I., Ondruska, J., Podoba, R., Sin, P., Bacik, P., and Trnik, A. (2015) The influence of heat on elastic properties of illitic clay Radobica. Journal of the Ceramic Society of Japan, 123, 874–879.CrossRefGoogle Scholar
  30. Jeppson, T.N. and Tobin, H.J. (2015) San Andreas fault zone velocity structure at SAFOD at core, log, and seismic scales. Journal of Geophysical Research-Solid Earth, 120, 4983–4997.CrossRefGoogle Scholar
  31. Kalinichev, A.G., Liu, X.D., and Cygan, R.T. (2016) Introduction to a special issue on molecular computer simulations of clays and clay-water interfaces: Recent progress, challenges, and opportunities. Clays and Clay Minerals, 64, 335–336.CrossRefGoogle Scholar
  32. Khazanehdari, J. and McCann, C. (2005) Acoustic and petrophysical relationships in low-shale sandstone reservoir rocks. Geophysical Prospecting, 53, 447–461.CrossRefGoogle Scholar
  33. Kitamura, K., Takahashi, M., Mizoguchi, K., Masuda, K., Ito, H., and Song, S.R. (2010) Effects of pressure on pore characteristics and permeability of porous rocks as estimated from seismic wave velocities in cores from TCDP Hole-A. Geophysical Journal International, 182, 1148–1160.CrossRefGoogle Scholar
  34. Kleipool, L.M., Reijmer, J.J.G., Badenas, B., and Aurell, M. (2015) Variations in petrophysical properties along a mixed siliciclastic carbonate ramp (Upper Jurassic, Ricla, NE Spain). Marine and Petroleum Geology, 68, 158–177.CrossRefGoogle Scholar
  35. Knuth, M.W., Tobin, H.J., and Marone, C. (2013) Evolution of ultrasonic velocity and dynamic elastic moduli with shear strain in granular layers. Granular Matter, 15, 499–515.CrossRefGoogle Scholar
  36. Lein, A.Y., Pimenov, N.V., Savvichev, A.S., Pavlova, G.A., Vogt, P.R., Bogdanov, Y.A., Sagalevich, A.M., and Ivanov, M.V. (2000) Methane as a source of organic matter and carbon dioxide of carbonates at a cold seep in the Norway Sea. Geochemistry International, 38, 232–245.Google Scholar
  37. Liu, D., Yuan, P., Liu, H.M., Li, T., Tan, D.Y., Yuan, W.W., and He, H.P. (2013) High-pressure adsorption of methane on montmorillonite, kaolinite and illite. Applied Clay Science, 85, 25–30.CrossRefGoogle Scholar
  38. Mazo, M.A., Manevitch, L.I., Gusarova, E.B., Berlin, A.A., Balabaev, N.K., and Rutledge, G.C. (2008) Molecular dynamics simulation of thermomechanical properties of montmorillonite crystal. II. Hydrated montmorillonite crystal. Journal of Physical Chemistry C, 112, 17056–17062.Google Scholar
  39. Militzer, B., Wenk, H.R., Stackhouse, S., and Stixrude, L. (2011) First-principles calculation of the elastic moduli of sheet silicates and their application to shale anisotropy. American Mineralogist, 96, 125–137.CrossRefGoogle Scholar
  40. Pellenq, R.J.M., Caillol, J.M., and Delville, A. (1997) Electrostatic attraction between two charged surfaces: A (N,V,T) Monte Carlo simulation. Journal of Physical Chemistry B, 101, 8584–8594.CrossRefGoogle Scholar
  41. Prasad, M., Kopycinska, M., Rabe, U., and Arnold, W. (2002) Measurement of Young’s modulus of clay minerals using atomic force acoustic microscopy. Geophysical Research Letters, 29, 13–1–13–4.CrossRefGoogle Scholar
  42. Renner, K., Henning, S., Moczo, J., Yang, M.S., Choi, H.J., and Pukanszky, B. (2007) Micromechanical deformation processes in PA/layered silicate nanocomposites: Correlation of structure and properties. Polymer Engineering and Science, 47, 1235–1245.CrossRefGoogle Scholar
  43. Ross, D.J.K. and Bustin, R.M. (2009) The importance of shale composition and pore structure upon gas storage potential of shale gas reservoirs. Marine and Petroleum Geology, 26, 916–927.CrossRefGoogle Scholar
  44. Sainz-Diaz, C.I., Hernandez-Laguna, A., and Dove, M.T. (2001) Theoretical modelling of cis-vacant and trans-vacant configurations in the octahedral sheet of illites and smectites. Physics and Chemistry of Minerals, 28, 322–331.CrossRefGoogle Scholar
  45. Sainz-Diaz, C.I., Palin, E.J., Dove, M.T., and Hernandez-Laguna, A. (2003) Monte Carlo simulations of ordering of Al, Fe, and Mg cations in the octahedral sheet of smectites and illites. American Mineralogist, 88, 1033–1045.CrossRefGoogle Scholar
  46. Sarout, J., Esteban, L., Delle Piane, C., Maney, B., and Dewhurst, D.N. (2014) Elastic anisotropy of Opalinus Clay under variable saturation and triaxial stress. Geophysical Journal International, 198, 1662–1682.CrossRefGoogle Scholar
  47. Sato, H., Ono, K., Johnston, C.T., and Yamagishi, A. (2005) First-principles studies on the elastic constants of a 1:1 layered kaolinite mineral. American Mineralogist, 90, 1824–1826.CrossRefGoogle Scholar
  48. Schon, J.H., Georgi, D.T., and Tang, X.M. (2006) Elastic wave anisotropy and shale distribution. Petrophysics, 47, 239–249.Google Scholar
  49. Schumann, K., Stipp, M., Behrmann, J.H., Klaeschen, D., and Schulte-Kortnack, D. (2014) P and S wave velocity measurements of water-rich sediments from the Nankai Trough, Japan. Journal of Geophysical Research-Solid Earth, 119, 787–805.CrossRefGoogle Scholar
  50. Skipper, N.T., Refson, K., and Mcconnell, J.D.C. (1991a) Computer simulation of interlayer water in 2:1 clays. Journal of Chemical Physics, 94, 7434–7445.CrossRefGoogle Scholar
  51. Skipper, N.T., Soper, A.K., and Mcconnell, J.D.C. (1991b) The structure of interlayer water in vermiculite. Journal of Chemical Physics, 94, 5751–5760.CrossRefGoogle Scholar
  52. Smith, D.E. (1998) Molecular computer simulations of the swelling properties and interlayer structure of cesium montmorillonite. Langmuir, 14, 5959–5967.CrossRefGoogle Scholar
  53. Van der Spoel, D., Lindahl, E., Hess, B., Groenhof, G., Mark, A.E., and Berendsen, H.J.C. (2005) Gromacs: Fast, flexible, and free. Journal of Computational Chemistry, 26, 1701–1718.CrossRefGoogle Scholar
  54. Vanorio, T., Prasad, M., and Nur, A. (2003) Elastic properties of dry clay mineral aggregates, suspensions and sandstones. Geophysical Journal International, 155, 319–326.CrossRefGoogle Scholar
  55. Wang, Z., Gelius, L.J., and Kong, F.N. (2009) Simultaneous core sample measurements of elastic properties and resistivity at reservoir conditions employing a modified triaxial cell - a feasibility study. Geophysical Prospecting, 57, 1009–1026.CrossRefGoogle Scholar
  56. Wang, Z.J., Wang, H., and Cates, M.E. (2001) Effective elastic properties of solid clays. Geophysics, 66, 428–440.CrossRefGoogle Scholar
  57. Wardle, R. and Brindley, G.W. (1972) Crystal-structures of pyrophyllite, 1Ttc, and of its dehydroxylate. American Mineralogist, 57, 732–750.Google Scholar
  58. Wenk, H.R., Lonardelli, I., Franz, H., Nihei, K., and Nakagawa, S. (2007) Preferred orientation and elastic anisotropy of illite-rich shale. Geophysics, 72, E69–E75.CrossRefGoogle Scholar
  59. Witteveen, P., Ferrari, A., and Laloui, L. (2013) An experimental and constitutive investigation on the chemo-mechanical behaviour of a clay. Geotechnique, 63, 244–255.CrossRefGoogle Scholar
  60. Woodruff, W.F., Revil, A., Prasad, M., and Torres-Verdin, C. (2015) Measurements of elastic and electrical properties of an unconventional organic shale under differential loading. Geophysics, 80, D363–D383.CrossRefGoogle Scholar
  61. Zhang, J.F., Clennell, M.B., Liu, K.Y., Pervukhina, M., Chen, G.H., and Dewhurst, D.N. (2016) Methane and carbon dioxide adsorption on illite. Energy and Fuels, 30, 10643–10652.CrossRefGoogle Scholar
  62. Zhang, W.N., Hu, H.X., Li, X.C., and Fang, Z.M. (2017) Changes in micromechanical properties of Na-montmorillonite caused by CO2/H2O sorption. Computational Materials Science, 129, 178–183.CrossRefGoogle Scholar
  63. Zhou, J.H., Lu, X.C., and Boek, E.S. (2016) Changes in the interlayer structure and thermodynamics of hydrated montmorillonite under basin conditions: Molecular simulation approaches. Clays and Clay Minerals, 64, 503–511.CrossRefGoogle Scholar
  64. Zou, C.N., Yang, Z., Zhu, R.K., Zhang, G.S., Hou, L.H., Wu, S.T., Tao, S.Z., Yuan, X.J., Dong, D.Z., Wang, Y.M., Wang, L., Huang, J.L., and Wang, S.F. (2015) Progress in China’s unconventional oil and gas exploration and development and theoretical technologies. Acta Geologica Sinica-English Edition, 89, 938–971.CrossRefGoogle Scholar

Copyright information

© Clay Minerals Society 2018

Authors and Affiliations

  • Junfang Zhang
    • 1
    Email author
  • Marina Pervukhina
    • 1
  • Michael B. Clennell
    • 1
  1. 1.CSIRO EnergyKensingtonAustralia

Personalised recommendations